ADAMSON IS10n Full-Range Line Array Cabinet with 2 ND10-LM Low-Mid Drivers User Manual
- June 6, 2024
- ADAMSON
Table of Contents
IS10n User Manual
Distribution Date: May 1st, 2021
Copyright 2021 by Adamson Systems Engineering Inc.; all rights reserved
This manual must be accessible to the person operating this product. As such,
the product owner must store it in a safe place and make it available upon
request to any operator.
The resale of this product must include a copy of this manual.
This manual can be downloaded from https://www.adamsonsystems.com/en/support
/downloads-directory/is-series/is10n
**Declarations
**
EU Declaration of Conformity
Adamson Systems Engineering declares that the products stated below are in
conformance with the relevant fundamental health and safety criteria of the
applicable EC directive(s), in particular:
Directive 2014/35/EU: Low Voltage Directive
IS10n – 973-0008, 973-0009, 973-0011, 973-5008,
973-5009, 973-5011
Directive 2006/42/EC: Machinery Directive
IS10 & IS119 Support Frame – 930-0028, 930-0035, 930-5028
Extended Beam – 930-0021, 930-5021
Moving Point Extended Beam – 930-0033, 930-5033
IS10 Micro Frame – 930-0030, 930-5030
Line Array H-Clamp – 932-0037
Signed at Port Perry, ON. CA – May 1st, 2021
Brock Adamson (President & CEO)
ADAMSON SYSTEMS ENGINEERING, Inc.
1401 Scugog Line 6, Port Perry (ON), L9L 1B2, Ontario,
Canada T: +1 905 982 0520, F: +1 905 982 0609
Email: info@adamsonsystems.com
Website: www.adamsonsystems.com
Safety & Warnings
Read these instructions, keep them available for reference. This manual can be
downloaded from
https://www.adamsonsystems.com/en/support/downloads-directory/is-
series/is10n
Heed all warnings and follow all instructions.
A qualifi ed technician must be present during the installation and use of this
product. This product is capable of producing extremely high sound pressure
levels and should be used according to the specifi ed local sound level
regulations and good judgment. Adamson Systems Engineering will not be liable
for damages caused by any possible misuse of this product.
Servicing is required when the loudspeaker has been damaged in any way, such
as when the loudspeaker has been dropped; or when for undetermined reasons the
loudspeaker does not operate normally. Inspect your products regularly for any
visual or functionality irregularities.
Protect the cabling from being walked on or pinched.
Read the appropriate IS-Series Rigging Manual before installing the product.
Pay attention to rigging instructions included in both Blueprint AV™ and the
IS-Series Rigging Manual.
Use only with the rigging frames/accessories specifi ed by Adamson, or sold
with the loudspeaker system.
This speaker enclosure is capable of creating a strong magnetic fi eld. Please
use caution around the enclosure with data storage devices such as hard
drives.
In an effort to continuously improve its products, Adamson releases updated
accompanying software, presets and standards for its products. Adamson
reserves the right to change the specifications of its products and the
content of its documents with no prior notice.
IS10n Sub Compact Line Array
- The IS10n is a sub-compact line array enclosure designed for extended throw capabilities. It contains two symmetrically arrayed 10” transducers and a 4” compression driver mounted on an Adamson sound chamber. The high-frequency sound chamber is designed to couple multiple cabinets across the entire intended frequency band without loss of coherence
- The operational frequency range of the IS10n is 60 Hz to 18 kHz. The use of proprietary technologies such as controlled Summation Technology and Advanced Core Architecture allows high maximum SPL and maintains a consistent nominal horizontal dispersion pattern of 80° down to 400 Hz.
- The enclosure has an unobtrusive visual design that blends seamlessly into the surrounding space, is made of marine-grade birch plywood, and has a four-point rigging system. Without sacrificing low resonance to the composite material, the IS10n is able to maintain a low weight of 25.6 kg / 56.5 lbs.
- Up to twenty IS10n can be flown in the same array when using the IS10 & IS119 Support Frame and up to 4 when using the IS10 Micro Frame. Nine rigging positions are available allowing vertical inter-cabinet splay angles from 0° to 10°. Always consult Blueprint AV™ and the IS-Series Line Array Rigging Manual for correct rigging positions (including ground stacking options) and installation procedures.
- The IS10n is intended to be used as a standalone system or with the IS119 companion subwoofer, which brings the usable frequency range down to 30 Hz. The IS10n can also be paired with other IS-Series subwoofers.
- The IS10n is designed for use with Lab. Gruppen’s D-Series line of installation amplifiers. The nominal impedance of the IS10n is 8 Ω per band, maximizing amplifier efficiency.
Wiring
- The IS10n (973-0008, 973-5008) comes with 2x Neutrik Speakon™ NL4 connections, wired in parallel.
- The IS10nb (973-0009, 973-5009) comes with an external barrier strip.
- Pins 1+/- are connected to the 2x ND10-LM MF transducers, wired in parallel.
- Pins 2+/- are connected to the NH4TA2 HF transducer.
IS10n & IS10nb Internal Wiring (IS10nb only has one input)
Amplification
The IS10n is paired with Lab.Gruppen D-Series amplifiers. Maximum quantities of the IS10n or IS10n paired with the IS119 per amplifier model are shown below. For a master list, please refer to the Adamson Amplification Chart, found on our website. https://adamsonsystems.com/support/downloads-directory /design-and-control/e-rack/283-amplification-chart-9/file
Presets
The Adamson LoadLibrary (https://www.adamsonsystems.com/support/downloads-
directory/design-and-control/erack/245-adamson-load-library-5-0-1/file)
contains
presets designed for a variety of IS10n applications. Each preset is intended
to be phase-aligned within the EQ overlap region with IS-Series subwoofers.
IS10n cabinets can be installed in an array with regular IS10 cabinets,
however, IS10n cabinets cannot share the same presets with IS10 cabinets.
When cabinets and subwoofers are positioned separately, phase alignment should
be measured with suitable software.
| |
---|---|---
IS10n Compact
Intended for use with an
an array of 4 IS10n| IS10n Short
Intended for use with an
an array of 5-6 IS10n| IS10n Array
Intended for use with an
an array of 7-11 IS10n
Control
Array Shaping overlays (found in the Array Shaping folders of the Adamson
LoadLibrary) can be recalled in the EQ section of Lake Controller to adjust
the contour of the array. Recalling the appropriate EQ overlay or preset for
the number of cabinets being used will give the standard Adamson frequency
response of your array, compensating for different low-frequency coupling.
Tilt overlays (found in the Array Shaping folders of the Adamson LoadLibrary)
can be used to alter the overall acoustic response of an array. Tilt overlays
apply a filter, centered at 1kHz, which reaches the noted decibel cut or boost
at the extreme ends of the listening spectrum. For example, a +1 Tilt will
apply +1 decibel at 20kHz and -1 decibel at 20Hz. Alternately, a -2 Tilt will
apply -2 decibels at 20kHz and +2 decibels at 20Hz.
Please refer to the Adamson PLM & Lake Handbook for detailed instructions on
recalling Tilt and Array Shaping overlays. https://adamsonsystems.com/support
/downloads-directory/design-and-control/e-rack/205-adamson-plmlake-
handbook/file
Weatherized
IS-Series weatherized models add an additional layer of environmental and
corrosion protection to Adamson’s already durable cabinet design. Weatherized
enclosures are ideal for marine and coastal venues, outdoor stadiums, open-air
performance spaces, and other permanent outdoor installations.
IS-Series weatherized cabinets feature the following additional protective
features.
Corrosion resistance
Corrosion resistance extends the lifetime performance of your system in
outdoor venues where water, salt, and acidity can impact durability and
function.
All structural steel elements of Adamson weatherized cabinets – including
rigging and rigging links – are made of a high yield strength stainless steel
alloy that offers 100% corrosion resistance.
Cabinet hardware is made of non-plated stainless steel, designed to provide
exceptional rust and corrosion resistance, particularly in high-saline
environments.
Environmental sealing
Additional protection of the cabinet helps ensure that loudspeaker performance
isn’t impeded by the harsh environments in which your system is deployed.
To guard against water and particle intrusion, the same two-part polyurea
coating that gives Adamson cabinets their life-extending exterior protection
is applied to the interior of the enclosure, creating a complete seal.
Weatherized models feature an exterior coating with a distinctively smooth
finish that allows for easy cleaning and removal of contaminants like dirt,
grime, saltwater or sand.
To protect against dust and other particles, a fine stainless steel mesh has
been added to all points of entry including behind the front grille screens.
Cabling for the IS-Series weatherized cabinets is pre-wired and protected
inside a gasket-sealed jack plate, with gland nuts in place to seal the
connection points.
Technical Specifications
IS10n Horizontal Pattern – Grey = -6 dB, Black = -12 dB
Frequency Range (+/- 3dB) | 60 Hz – 18 kHz |
---|---|
Nominal Directivity (-6 dB) H x V | 80° x 10° |
**
Maximum Peak SPL
| 141.3 dB
Components LF| 2x ND1O-LM 10″ Neodymium Driver
Components HF| Adamson NH4TA2 4″ Diaphragm / 1.5″ Exit Compression Driver
Nominal Impedance LF| 8 0 (2 x 16 0)
Nominal Impedance HF| 8 0
Power Handling (AES / Peak) LF| 700 / 2800 W
Power Handling (AES / Peak) HF| 160 / 640 W
Rigging| Integrated Rigging System
Connection| 2x Speakon’ NL4 or Barrier Strips
Height Front (mm / in)| 300 / 11.8
Height Back (mm / in)| 175 / 6.9
Width (mm / in)| 737 / 29
Depth (mm / in)| 518 / 20.4
Weight (kg / Ibs)| 25.6 / 56.5
Colour| Black & White (Standard), RAL Colours (On-Demand)
Processing’| Lake
** 12 dB crest factor pink noise at 1m, free field, using specified processing and amplification