ADAMSON S118 Speaker Tour Sound User Manual
- June 4, 2024
- ADAMSON
Table of Contents
ADAMSON S118 Speaker Tour Sound
Distribution Date: August 15, 2022. Copyright 2022 by Adamson Systems Engineering Inc.; all rights reserved This manual must be accessible to the person operating this product. As such, the product owner must store it in a safe place and make it available upon request to any operator. This manual can be downloaded from https://adamsonsystems.com/support/downloads- directory/s-series/s118.
Declarations
EU Declaration of Conformity
Adamson Systems Engineering declares that the products stated below are in
conformance with the relevant fundamental health and safety criteria of the
applicable EC Directive(s), in particular:
Directive 2014/35/EU: Low Voltage Directive
992-0009 S118
Directive 2006/42/EC: Machinery Directive
- 930-0021 Extended Beam
- 930-0025 Ultra-Compact Support Frame
- 930-0033 Moving Point Extended Beam
- 932-0043 Extended Lifting Plates
- 932-0047 Line Array H-Clamp
Signed at Port Perry, ON. CA – August 15, 2022
Brock Adamson (President & CEO)
ADAMSON SYSTEMS ENGINEERING, Inc.
- 1401 Scugog Line 6 Port Perry, Ontario, Canada L9L 0C3
- T: +1 905 982 0520,
- F: +1 905 982 0609
- Email: info@adamsonsystems.com
- Website: www.adamsonsystems.com.
Safety & Warnings
Read these instructions, keep them available for reference. This manual can be downloaded from https://adamsonsystems.com/support/downloads- directory/s-series/s118.
- Heed all warnings and follow all instructions.
- A quality ed technician must be present during the installation and use of this product. This product is capable of producing extremely high sound pressure levels and should be used according to the specifi ed local sound level regulations and good judgment. Adamson Systems Engineering will not be liable for damages caused by any possible misuse of this product.
- Servicing is required when the loudspeaker has been damaged in any way, such as when the loudspeaker has been dropped; or when for undetermined reasons the loudspeaker does not operate normally. Inspect your products regularly for any visual or functionality irregularities.
Protect the cabling from being walked on or pinched. View the S-Series Rigging Tutorial video and/or read the S-Series Rigging Manual before suspending the product. Pay attention to rigging instructions included in both Blueprint and the S-Series Rigging Manual. Use only with the rigging frames/accessories specifi ed by Adamson, or sold with the loudspeaker system. This speaker enclosure is capable of creating a strong magnetic fi eld. Please use caution around the enclosure with data storage devices such as hard drives.
In an effort to continuously improve its products, Adamson releases updated accompanying software, presets and standards for its products. Adamson reserves the right to change the specifications of its products and the content of its documents with no prior notice.
**Product Introduction
**
- The S118 is an ultra-compact subwoofer enclosure designed for extended LF capabilities. It contains one ND18-S 18” LF driver.
- Up to 16 S118 can be flown when using the Ultra-Compact Support Frame.
- The S118 can be flown or stacked in the same array as the S7 without the need for additional rigging hardware between the two types of cabinets.
- Adamson’s use of proprietary technologies such as Advanced Cone Architecture give the S118 an extremely high maximum SPL level of 133 dB.
- The nominal impedance of the S118 is 8 Ω.
- The operational frequency range of the S118 is 35 Hz to 100 Hz, +/- 3 dB.
- The S118 is intended to be paired with other S-Series products with a crossover frequency range of 80Hz.
- The wooden enclosure is made of marine grade birch plywood and has an aluminum and steel rigging system mounted on each corner, and a pole mounted on top. Without sacrificing lowered resonance to the composite material, the S118 is able to maintain a low weight of 31 kg / 68.4 lbs.
- The S118 is designed for use with Lab. Gruppen’s PLM+ Series amplifiers.
Wiring
The S118 (992-0009) comes with 5x Neutrik Speakon™ NL4 connections. The 2 rear
‘Parallel’ NL4 connections pass pin 1 +/- to the driver. The 2 front NL4
connections pass pin 2 +/- to the driver.
There is one rear ‘Output’ connection. The rear NL4 Parellel connection pins 2 +/- is passed thru the NL4 Output connection pins 1 +/-.
Amplification
The S118 is paired with Lab Gruppen PLM+ Series amplifiers. Maximum quantities
of the S118 per amplifier model are shown below. For a master list, please
refer to the Adamson Amplification Chart, found here on the Adamson
website.
Presets
The Adamson Load Library contains presets designed for a variety of S118
applications. When flown or stacked in the same array as an S7, all S118
presets contain the inherent delay needed to be properly phase-aligned. For a
master list, please refer to the Adamson PLM & Lake Handbook. When flown or
ground stacked separately, S118 subs should be phase-aligned using measurement
software. All S118 presets are also available in CC (Conventional Crossover)
versions minus 5 ms delay.
Cardioid Dispersion
Technical Specifications
Frequency Range (+/- 3dB) 35 Hz – 100 Hz
Maximum Peak SPL** 133 dB
Components LF| ND18-S 18” Kevlar Neodymium Driver
Nominal Impedance LF 8 Ω
Power Handling (AES / Peak) LF| 500 / 2000 W
Rigging Integrated Rigging System
Connection| 5x Speakon™ NL4 (2x Front 1+/1-, 2x Rear (2+/2-, and 1x Rear
Output (Pin 2 to 1))
Height (mm / in) 508 / 20
Width (mm / in)| 527 / 20.75
Depth (mm / in) 495 / 19.5
Weight (kg / lbs)| 31 / 68.4
Processing Lake
12 dB crest factor pink noise at 1m, half-space, using specified processing
and amplification
Accessories
There are a number of accessories available for the Adamson S118 subwoofer cabinets. The list below is only a few of the accessories available.
Ultra-Compact Support Frame (930-0025)
Support frame for S7, CS7, S118, and CS118 enclosures
Extended Beam (930-0021)
Accommodates a greater array of articulation
Moving Point Extended Beam (930-0033)
Extension beam with continuously adjustable pick point
Line Array H-Clamp (932-0047)
Horizontal articulator clamp to be used with S-Series/CS-Series/IS-Series line
array rigging frames
Extended Lifting Plates (930-0033)
Lifting plates with fine resolution pick points for single-point hangs.
Ultra-Compact Subwoofer Dolly (938-0023)
Transports up to 2x S118 or CS118
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>