ADAMSON S10p Web Box User Manual

: June 4, 2024
: ADAMSON

ADAMSON S10p Web Box

Heed all warnings and follow all instructions.

A qualiﬁed technician must be present during the installation and use of this product.
This product is capable of producing extremely high sound pressure levels and should be used according to the speciﬁed local sound level regulations and good judgement.
Adamson Systems Engineering will not be liable for damages caused by any possible misuse of this product.
Servicing is required when the loudspeaker has been damaged in any way, such as when the loudspeaker has been dropped; or when for undetermined reasons the loudspeaker does not operate normally.
Inspect your products regularly for any visual or functionality irregularities.
Protect the cabling from being walked on or pinched.
View the S-Series Rigging Tutorial video and/or read the S-Series Rigging Manual before suspending the product.
Pay attention to rigging instructions included in both Blueprint and the S Series Rigging Manual.
Use only with the rigging frames/accessories speciﬁed by Adamson, or sold with the loudspeaker system.
This speaker enclosure is capable of creating a strong magnetic ﬁ eld. Please use caution around the enclosure with data storage devices such as hard drives.
In an effort to continuously improve its products, Adamson releases updated accompanying software, presets and standards for its products.
Adamson reserves the right to change the specifications of its products and the content of its documents with no prior notice.

S10p Sub Compact Point Source

The S10p is a sub-compact, 2 way, full range point source enclosure designed with high output level and high clarity in mind.
It contains two symmetrically arrayed 10 transducers and a 3 compression driver mounted on an Adamson waveguide.
The high frequency waveguide is rotatable in increments of 90° and is available with dispersion patterns of either 70° x 40° HxV or 100° x 50° HxV.
Adamson’s use of proprietary technologies such as Advanced Cone Architecture give the S10p an extremely high maximum SPL level.
The nominal impedance of the S10p is 8 Ω per band.
The operational frequency range of the S10p is 60 Hz to 18 kHz, +/- 3 dB.
The S10p is intended to be used as either a standalone system, or a fill enclosure in tandem with other S-Series products.
The S10p is designed to pair easily and coherently with Adamson subwoofers.
The wooden enclosure is made of marine grade birch plywood, has an inset steel pole mount on the bottom, and has a steel rigging system mounted on each side.
The rigging discs are compatible with several different Adamson rigging accessories. Without sacrificing low resonance to composite material, the S10p is able to maintain a low weight of 26 kg / 57.4 lbs.
The S10p is designed for use with Lab grippe’s PLM+ Series amplifiers.

Wiring

The S10p (70×40 – 963-0008/100×50 – 963-0010) comes with 2x Neutrik Speak on NL4 connections, wired in parallel.
Pins 1+/- are connected to the 2x ND10-LM MF transducers, wired in parallel, pins 2+/- are connected to the NH3-8 HF transducer.

S10p Internal Wiring

Amplification

The STOP Is paired With Lab Gruppen PLM+ Series amplifiers. Maximum quantities of the STOp per amplitier model are shown below. For a master list, please refer to the Adamson Amplification Chart, found here, on the Adamson website.

1x S10p per circuit
2x S10p per amplifier
4x S10p per circuit
8x S10p per amplifier

Presets

ADAMSON S10p Web Box 5

he Agamson Load Liorary Contains presets designed for a variety or Sup applications. Inese presets are designed to pair with either Adamson subs, or Adamson Line Arrays. For a master list, please refer to the Adamson PLM & Lake Handbook Phase alignment with additional cabinets and subwoofers should be measured with suitable software.

Dispersion

S10p Horizontal Pattern (70×40)

S10p Horizontal Pattern (40×70)

S10p Horizontal Pattern (100×50)

Horizontal Pattern (50×100)

Technical Specifications

ADAMSON S10p Web Box 10

Frequency Range +/- 3dB 60 Hz – 18 kHz

Nominal Directivity -6 dB H x V         70° x 40° / 100° x 50° (Rotatable)
Maximum Peak SPL| 139 dB
Components LF        2x ND10LM 10” Kevlar Neodymium Driver
Components HF Adamson NH3-8 3 Diaphragm / 1.4 Exit Compression Driver
Nominal Impedance LF        8 Ω (2 x 16 Ω in parallel)
Nominal Impedance HF| 8 Ω
Power Handling AES / Peak LF         700 / 2800 W
Power Handling AES / Peak HF         110 / 440 W
Rigging        Integrated Rigging System
Connection| 2x Speakon NL4
Height (mm / in)        737 / 29
Width Front (mm / in)| 326 / 12.8
Width Back (mm / in)        203 / 8
Depth (mm / in) 442 / 17.4
Weight kg / lbs) 26 / 57.4
Processing Lake

Accessories

There are a number of accessories available for the Adamson S10p point source cabinets The list below is only a few of the many available accessories.