LISKA SV-M14 Smart Bracelet Instructions
- June 6, 2024
- LISKA
Table of Contents
LISKA SV-M14 Smart Bracelet
Compatible Operating System and requirements.
Android 4.4 and higher/ IOS 8.5 iPhoneSs or higher/ Bluetooth 4.0
Preparation
Make sure the battery is fully charged the first time. Charge 1t 1 – 1.5 hours
1f the device cannot be turned on.
The smart bracelet cannot be worn while charging.
Connection
Download the app.
Scan the QR code to download the App.
Make sure that Bluetooth is activated and open “WearFit”
Select to pair the bracelet, find the device name m the list and connect it.
Then go to the mam interface.
Function specifications
-
Time: The bracelet display shows time, date and remaining battery. (Once the smart bracelet Is connected to the phone, the time will be synchronized with the phone time. The time cannot be set on the bracelet).
-
Status: records the user’s steps daily, distance traveled, calories consumed.
-
Heart Rate: Measure heart rate every hour, or measure it manually. Press and hold to enter the heart rate measurement interface
-
Blood Pressure: Measure blood pressure every hour or measure it manually. Press and hold to enter the blood pressure measurement interface.
-
Blood oxygen: measure blood oxygen every hour or measure it manually. Press and hold to enter the blood oxygen measurement interface.
-
Sports: Press and hold on the sports mode interface to enter the sports selection screen. There are 5 different sport modes to select indoor race, outdoor running, cycling, walking and exercise mode. Press and hold in the selected sport mode to start recording the sport, time, calories burned . Press to pause, press and hold to return
-
Weather: Actual weather conditions are synchronized with your device data and displayed on the time interface. The smart bracelet needs to be
connected to the App and the GPS function of the device must be activated. -
More: Do not disturb (press and hold to cancel or activate vibration), music (press and hold to enter the music control panel, press to change, press and hold to confirm), timer (press and hold to enter the timer, press to pause or start), find my phone (press 5 sec. to enter the mode find phone, press to start, find the phone through ringtone and vibration, bracelet to stop). Make sure the phone and smart bracelet are connected and within the operating range.
-
Settings: Turn off (press and hold to turn off, press to change), about (press and hold to check the firmware version, MAC address, press and hold
to return or come back after 5 seconds). -
Others: Charge Alert, Alarm Reminder, Sedentary Reminder, Incoming Call Screen, Shake to Take Photos, System Update, WeChat I 00 I Notification text message.
Frequently asked questions
-
Can’t find the bracelet or can’t connect?
Make sure that Bluetooth is turned on in the phone and that the phone’s operating system is Android 4.4 or higher and iOS 8.4 or higher. If you still can’t connect, go to Settings on your phone – app management – authorization management – app access authorization, Find “WearFit” and all permissions to allow access. Then go back into the settings to activate the GPS location service, restart the phone, try connecting again.
Make sure the bracelet is fully charged. Feel free to contact us if It doesn’t work normally with the battery charged. -
After pairing the bracelet, does the application show that it is not connected or that the remaining battery is 0%?
In that case the bracelet and the phone are not connected properly, please pair the devices again -
Can’t connect the device to the App?
Pull down and refresh the main interface, the data will be sync manually, then the data can be displayed m the App. Auto data sync only It will sync on the first pairing. The data will then automatically sync every hour. Also, don’t forget to open the data measurement hourly. If it is not open, the histogram has no data. -
After updating, no data is displayed.
Go to app settings – restore factory settings – turn off smart bracelet – turn on smart bracelet and reconnect to app. The data can be loaded into the application. -
Is the bracelet time not synchronized after connecting to the phone?
Go to phone settings – Application Management – Perm1ss1on Management – Open App Permissions – re-link the bracelet. Pull down and refresh the main interface of the App.
Specifications
Observations
- If there is a product quality problem or the use of the product is not clear, please contact our store via email, we will try to resolve it as soon as possible.
- The measurement data for this product is for reference only, not for a medical purpose or base. Follow your doctor’s instructions and do not trust these data to self-diagnose or treat yourself.
- The degree of water resistance is IP67, it can be used for daily waterproofing. But the bracelet cannot be used for diving, or Immersmg m water for a long time. Also, this product does not tolerate hot water, because steam will affect the bracelet.
- The company reserves the right to modify the content of this manual without prior notice. Some functions are different in various software versions, It Is normal.