Elektro2Rad FREERIDE X2 HUB Street Legal Electric Scooter Instruction Manual

Elektro2Rad FREERIDE X2 HUB Street Legal Electric Scooter

PREPARATION

Congratulations! You’ve acquired one of the most popular e -scooters. The most innovative and thoughtful e -scooter of his generation. In order to enjoy driving for a long time, take your time and read this manual carefully before you start driving. The manufacturer is constantly working on the further development of its models. Please understand that changes in the scope of delivery in form, equipment, and technology are therefore possible at any time. Therefore, no claims can be derived from the information, pictures and descriptions of these instructions.

NOTE

Important
Please read the instructions carefully before using the device.
Symbols used
Important information for your safety is specially marked. Please follow these instructions to avoid injuries and damage to your FREERIDE X2 HUB:

Warning
Warn of health hazards and indicate possible injury hazards.

NOTE
Indicates possible hazards to FREERIDE X2 HUB or other objects. Non -compliance may lead to the conclusion of guarantees
NOTE
Highlights tips and information for you.

Preliminary legal observations

3.1. Road transport (EEC STREET models only)

To operate this vehicle you need a driving license and an insurance number. An EU Operating Licence (EEC) is attached to the roller. With this paper, you can purchase a license plate at any insurance.

Driving license
Model: FREERIDE X2 HUB / 45KMH Persons of 16 -year -old age with moped or car license.
Helmets
Due to its maximum speed of approximately 45 km /h, the FREERIDE X2 HUB may only be driven with a helmet.

EEC Document (European Certificates of Conformity)|
For the approval of your FREERIDE X2 HUB, use the attached DIN A4 sheet (European Certificate of Conformity EEC). This makes the scooter acceptable throughout Europe. EEC approval requires a fixed seat for driving in public transport. Holding in a standing position is not permitted. FREERIDE X2 HUB may only be driven by one person.

Walking and cycling paths
The use on public bicycles and pedestrians is not permitted unless this is shown separately.

Safety

Improper use can lead to serious injuries. The driver can minimize this risk by using different safety standards, such as: wearing a helmet, goggles, gloves, elbow and knee protectors and appropriate footwear. Do not use the scooter on smooth, oily, or unpasteurized surfaces. Do not drive under the influence of alcohol and /or drugs. Avoid uneven substrates, impact holes, cracks in the pavement, and other obstacles. If wet, note the increased risk of slipping and falling.  The device should not be used by persons with reduced vision, balance, coordination, reflexes, muscle and bone strength and estimation.It should not be used by people who cannot or do not want to take responsibility for their actions.The driver assumes all risks associated with the use of the vehicle.

Package content

Your scooter comes with the below accessories:

1. instructions
2. Tool kits
3. Fuse
4. License plate
5. Charger
6. COC certificate

First（you can see we add a picture/note with the logo）

Instructions for unlocking the scooter
To open the scooter, pull out the safe PIN firstly(a is the safety pin in picture ①) and then press the handle to open down with one hand (see arrow b and c), while gently press the handlebars up with the other hand. Picture ② is the unfolded scooter, please make sure you insert the safe PIN(d in picture ②)

NOTE Push the handlebars gently into the vertical position until you feel that the mechanism is pressed, make sure that insert safe PIN.

Instructions for mount handlebar

1. Place the alloy clamp in the correct position as in the picture.①, then tighten all M8X25 skews.
2. Place the handlebar to the clamp bottom and attach the clamp cap as picture②, adjust the correct angle and tighten all screws M8X20.
3. Open the holder of the display as picture ③ onto the handlebar, adjust the correct position and tighten all screws on the holder.

After the handlebar is fixed, the QUICK-CONNECT connectors for an accelerator, light /horn switch, brake handles, lamp, ignition, and display must be connected. Note the correct polarity and fit accuracy of the connectors.

Commissioning

Connect battery and controller
Now insert the BATTERY PACK into the battery compartment by tapping the tread surface upwards, and connecting the plug XT90 and XT60 to the controller device. Please disconnect the battery plug while you replace or take out the fuse. Please make sure the fuse inserts the end of the safe valve, or it may cause the broken of fuse and safety valve after short driving.

NOTE XT90 for rear motor controller, XT60 for front motor controller.

Mount seat
Insert the seat post to the bottom tube as ①. Don™t forget to put the seat safe PIN as ②, safe PIN.was inserted as ③

Place seat onto upper seat post and tighten screws. In order to allow comfortable, fatigue-free and thus safe driving, the saddle height should be adjusted to the height of the body. The toes must still be able to touch the ground. Release quick lever, determine saddle height, and clamp. The clamping force can be adjusted by adjusting the nut to the quick lever.

Warning
An unscrewed quick-release lever can be opened again. This could allow the saddle to slide down during the ride.
Heavy falls can be the result.

Mount license plate and plate light
Find the license plate and screws for fixing, and tighten two screws (see arrow a) as the following picture shows. You will find the light for the license plate on the rear fork of the scooter, then stick the light on plate.(see arrow b, the position that sticks plate light)

Fold
The seat must be removed before folding.

Make sure the ignition lock is on AUS.
After using the scooter, you can fold it for easier storage or transport. To do this, pull out the safe PIN firstly(safe PIN is on the position of ① ), and then face both sides of the scooter. Use your left hand to push the hand post,(position ③) with your right hand simply pull the lever (position ②)back to collapse and gently push the handlebars down, making sure you do not hurt yourself. Turn the handlebars over until you feel the mechanism is pressed. In order to make the scooter locked as foldable, make sure to insert a safe PIN at position ④.

Sidebar
Attention in the case of unplugged main stands, the current is completely interrupted by a safety switch. (as picture ①)This is for your safety and is mandatory for road traffic authorization. The roller can therefore only be driven with a high-tilted sidebar.

NOTE
The E -scooter can’t drive until the sidebar is up as picture ②. Picture ① shows the situation of power-off protection when the sidebar touches the floor.

Ignition
The delivery includes four keys.(two keys for ignition, two keys for steering lock) Place the ignition key on position “1” so that the scooter is ready for use. Arrow a shows the ignition key, arrow b shows key for the steering lock, and arrow c shows the position of the steering lock.

NOTE
Remember to take out the key of the steering lock whether the steering lock is open or close, otherwise, keys will be easily lost.

Horn / Light / Mirror
The front and rear lights is powered on when opening the ignition key You’ll find the Horn button on the left of the handlebar. You will find a mirror holder on the left and right of the brake level, fixing the left and right mirror onto the correct position.

NOTE
EEC street models without lights button, front and rear lights must keep long bright status while the ignition key is power on as new EEC transport rules.

Battery

The EEC STREET models are equipped with Lithium batteries with a water-proof box.

NOTE

Important information that you should read before starting operations and which we strongly recommend:

• The batteries are charged to approximately 50% in the new state.
• The battery develops its maximum power after about five charging cycles.
• Turn off power firstly when mounting or removing batteries

NOTE

• The battery and charger of FREERIDE X2 HUB are matched. Therefore, never charge the batteries with a charger other than the supplied charger.
• The maximum battery life is achieved by charging them at ambient temperature between +10 degrees and max. +30 degrees. -The batteries can warm up when they are under heavy pressure. lease note room temperature before loading.
  NOTE
  As a consumer, you are legally obliged to return used batteries and batteries to designated collection points. You can drop your spent batteries and batteries at the public collection points in your municipality or anywhere where batteries and batteries of that type are sold. Batteries and batteries don’t belong in the trash.
  Fuse
  The battery system is protected by a plug-infuse. Replacement fuses can be found in the supplied toolbox if required. On the fuse, you will find the specification printed.
  Battery Capacity / Type
  FREERIDE X2 HUB: 60V 20Ah Lithium batteries. Use only the high-quality original batteries of the same quality. If you need replacement batteries, please contact your dealer.
  Use of batteries
  New batteries must always be fully charged the first five times. The more you charge your batteries, the better. They save batteries if they are not discharged below 20% residual capacity. Never charge batteries at minus degrees -let the batteries at minus degrees warm up to room temperature before charging them. This considerably prolongs the service life.
  Charging device
  In order to prevent risks of injury, you must only charge the supplied and installed battery with the charger. Other batteries could explode if charged. The use of accessories or batteries that are not sold or recommended by us may lead to fire risk, electric shock or other serious injuries. In any case, avoid operating the charger in a humid or wet environment. Avoid any water entering the device. If there is any liquid, disconnect the charger immediately from the mains and have it checked by the specialist. The device should be safe and level. Always disconnect the device from the mains if not in use. Never pull on the cable, as this avoids cable damage and the risk of electrocution. Never operate the charger with a damaged cable or plug or with damage to the plastic housing. Do not dismantle or open the charger yourself under any circumstances. Any manipulation or incorrect assembly may result in an electric shock or fire.

Charging

1. Charge battery in the vehicle: Make sure the E -Scooter’s turned off. Take the charger and attach it to a socket. The red light on the charger should now turn on to show that it has power. Insert the 3 -pole charger on the right front bottom of the vehicle

The status display on the charger will be red to indicate that the charging process has started. If you switch the display to green, you can remove the charger from the scooter. You can use the scooter now.

• Don™t recommend charging the batteries all over of night.
• Don™t recommend charging the batteries over 12 hours.
• Recommend disconnecting the charger when you go out in a long time.
• Recommend to keep batteries charged in a scooter.

Maintenance and instructions for charging the batteries

NOTE
Failure to comply with the instructions may result in the battery being discharged. No warranty can be accepted for low-charged batteries. Therefore, in order to achieve the longest possible life of the battery, it is imperative that the following information be taken into account:

• The charger shall not be activated in a battery temperature range below +10 and over +60 degrees. Therefore, bring the battery to room temperature before each charge.

• hoose a storage place where the FREERIDE X2 HUB is stored as far as possible at room temperature. -Reload the battery after use, irrespective of the previous route or the energy taken. -The charger is an intelligent system with monitoring and control functions.

• After the charging process is completed, the charger must be disconnected from the battery and must not be left at the disconnected charger.

• The battery in case of prolonged non-use by no means permanently on the charger leave connected. Keep the vehicle in a dry room at room temperature when it is closed (e.g. in winter).

• Always recharge your battery every three months at the latest. -When the vehicle is restarted after a long service life (e.g. after a winter break), the battery should be connected to the charger for complete charging. -Duration of charge: The battery is fully charged with the supplied charger with 2.0 A charging power in approximately eight hours.

• The battery should be fully charged before first use.

• Never let the batteries completely discharge. Use only original FREERIDE X2 HUB-approved batteries to prevent damage to the controller. The use of unauthorized batteries results in the loss of the warranty.
  The maximum achievable range with a charge of the battery depends on a number of factors. These include the battery and charging condition, temperature conditions, route profile, and driver weight as well as the corresponding driving mode (e.g. stop-go, full load, mountain valley, etc.).
  WARNING
  In case of disturbances check:

• Is the power cable properly connected? -Are the contacts of the charger and the battery clean, not damaged or bent?

• Is the battery damaged or defective?

• Is the charger plug stuck in the battery box? If a proper charge of the battery is not possible, please have the battery and charger checked by a specialist workshop.

Tacho

1.  Installation Place the display in the middle of the handlebar and adjust to the correct position. Tighten the screw on the holder of the display. Connect the 4PIN plug on display to another plug from harnesswire.

NOTE
Please turn off the power before connecting the display. The display as a standard accessory on FREERIDE X2 HUB EEC Street models.

Main function display

1. Power capacity
2. Speed KM/H-Mph
3. Power, Eco, and Walk mode
4. ODO/TRIP

Motor mode adjustment

Setting button

1. Fifi (fi+fl)
2. fiDOWNfi (fi-fi)

powerful shows a max speed of 45km/h with two motor walking, fiECOfl shows half of the speed with one motor working, and dialkyl (a symbol of walking man on-screen) shows walk speed around 6km/h. The mode can be changed by pressing the fiUPfl (fi+fl) or fi DOWNfl (fi-fi)button.

NOTE
The manufacturer already set all functions and data, please DO NOT change anything, the incorrect setting could lead to serious errors, it this happened, please contact your dealer. The wrong operation could result in the loss of the warranty
Other functions and setting
Please read TACHO HANDBOOK.

Starting and driving

WARNING – Risk of falling!
Please note the following points to minimize the risk of falling:

1. Before you go, always open the sidebar.
2. Hold the steering wheel straight.
3. When turning, starting in a curve or when driving in a narrow curve the brake Easy to operate. This interrupts the electric drive force and safe driving without driving influences.
   During the trip:
   If there are any unusual noises or problems, stop the journey and inform the manufacturer. Service addresses can be found in the operating manual.

Brakes

The electric scooter is equipped with front and rear disc brakes, which are operated by the hand brake handle on the steering wheel. The scooter is equipped with a regulator which interrupts the power supply to the engine in the short term when the brake lever is pressed.

Attention
The front brake can react very directly. Practice braking on a flat and dry surface to familiarize yourself with the braking system. The brake path depends on the driver’s weight, weather and surface. A quiet of the brakes is nothing to worry about. The brake lining should then be applied slightly. In the case of hard-quality brake linings, a Qietsch can occur frequently. For soft coatings less rare, but therefore increased wear.

Tires and wheels

The scooter has identical front and rear tires. Only tires approved by the manufacturer may be used when changing tires. Other tires lead to a loss of road clearance.

Attention
In case of disregard, the operating license expires. Tire: It is recommended to pump the tires to air pressure of 3.5 in cash. You can do this at any gas station. These are standard car valves.

Guarantee

The E -the scooter is guaranteed according to the current legal deadlines. The warranty excludes worn parts such as batteries, tires, hoses, rims, brake parts, wheel bearings, and steering head bearings.
Also excluded are damages due to improper use, in particular jumping, descending steps, sidewalks, stairs, and the like, running on the muddy ground, sand or gravel, and overloading due to excessive weight. Gross pollution causes higher wear and is therefore not covered.

1. The battery is guaranteed for six months. The manufacturer may make the required repair or refuse to exchange the defective part if this is possible only at a disproportionate cost. In this case, the manufacturer turer may remedy the deficiency by means of any other means of subsequent compliance. Where both types of after-completion are possible only at a disproportionate cost, the manufacturer may refuse the full after-completion. The customer then has legal claims. Replaced parts shall be transferred and referred to the ownership of the manufacturer.
2. By installing spare parts in the context of a warranty case, the warranty period running from the delivery of the vehicle to the customer shall not be extended.
3. The warranty shall be without prejudice to wear and tear arising from normal use, as well as wear and tear resulting from improper handling and use. Oxidation and corrosion are caused by environmental influences and do not constitute a deficiency under the guarantee law.
4. The buyer loses his warranty when manipulating the vehicle, such as modifications to the cable, the battery pack, the sensor, the braking system, as well as when installing accessories and spare parts that have not been released by the manufacturer. The loss of warranty entitlement results in all improper interventions, such as by an unskilled workshop, as well as non -compliance with maintenance intervals in a specialized workshop. 5. In case of a warranty case, the buyer shall provide the seller with the duly completed service booklet including proof of payment.

Accessories Parts

Only use original MAXIMOV accessories and parts. The use of non-specified accessories may lead to accidents and also to the cancellation of the warranty.

Errors

No function at all.

| The fuse was not used or defective.

The battery pack is not or is not properly connected.

The stand didn’t go up.

| Put the fuse on.

Connect the shopping bag according to instructions.

Knock on the stand.

The device does not move, although the gas lever was pressed.

| The stand didn’t go up.

The gas handle is faulty or not correctly connected.

The batteries can’t be recharged anymore.

The batteries have reached the end of their life. Brake levers are engaged.

The brake handle breaker is defective.

| Knock on the stand.

Check the gas handle, wiring and replace it if necessary.

The connectors may have been switched when commissioned. Watch out for the right countersign.

Replace the batteries or the charger. Replace the batteries.

Release the brake.

Replace the brake handle

The device only runs periodically or very slowly.

| The batteries are not fully charged or have a polarity problem.

The engine or control unit is overheated. The connectors have a wavelength contact.

The brake arches are not correctly adjusted and release the brake contact.

The engine ran hot.

| Reload the batteries or replace them.

Wait about 15 -minute cooling time. Do not use full throttle for a while.

Check all connections to the correct seat. Set the bow line precisely.

Let the engine cool down. Avoid extreme climbs when the speed decreases vehemently and only reaches step speed.

The device fails abruptly while driving.| The controller is defective

The fuse on the battery pack is defective (if LED is off).

| Please contact your dealer. Replace the fuse.

The batteries can no longer be charged or will not last much longer

| Batteries have reached the end of their life or poor polarity among themselves. These should be replaced by a new battery pack.

The charger is no longer functioning properly.

The connection cable from the charging box to the control unit is no longer properly connected.

| Replace the batteries. Replace the charger.

Check the connection of the charger and cable in the battery compartment, as well as the fuse.

The light on the charger switches

to green immediately.

| TThe batteries are already charged. Some models are delivered fully loaded.

The charger’s broken.

| However, charge the battery for another four hours before using the scooter for the first time.

Replace the charger.

The following table will help you identify and correct common problems that can occur with an E -scooter.

Instructions

rear arm-swing
Dimension(LxWxH)| 1300 x 640 x 1280mm
N.W/G.W| 44.8/49.8KGS
Max load| 95KGS
Tire size| 90/65-6.5 e-mark approval
Headlight| LED 12V e-mark approval
Taillight| LED 12V e-mark approval
Number plate light| LED 12V e-mark approval
Horn| 12V e-mark approval
Mirror| e-mark approval
Speedometer| LCD digital display
Suspension| Single shock / dual shock (F/R)
Brake system| Disc brake (F/R)

NOTE

Regular and properly implemented care measures serve to maintain the value of FREERIDE X2 HUB and are important prerequisites for the recognition of warranty claims. Corrosion due to lack of care or winter operation is not guaranteed!!!

• Paint, rubber and plastic parts shall not be treated with aggressive or penetrating cleaning or solvents. This can lead to damage.
• Do not use a pressure jet for cleaning! -The high water pressure can cause severe damage to electronics, tires, warehouses, seals. -Use a soft, moist cloth to wash.
• Do not wipe dirt with dry cloth, as otherwise scratches in the paint arise. Care The electric scooter should be maintained regularly and if necessary with commercial, pH -neutral and non -aggressive preservatives and care. Treat parts at risk of corrosion regularly with preservatives and care products, but especially in winter.

Technical data

rear arm-swing
Dimension(LxWxH)| 1300 x 640 x 1280mm
N.W/G.W| 44.8/49.8KGS
Max load| 95KGS
Tire size| 90/65-6.5 e-mark approval
Headlight| LED 12V e-mark approval
Taillight| LED 12V e-mark approval
Number plate light| LED 12V e-mark approval
Horn| 12V e-mark approval
Mirror| e-mark approval
Speedometer| LCD digital display
Suspension| Single shock / dual shock (F/R)
Brake system| Disc brake (F/R)

Maintenance

Work to be done| Before departure| 14 -day| Monthly| If needed
---|---|---|---|---
All screws and clamps and

Check couplings on a fixed seat and if necessary. Adjust.

| | | |
Check chain tension, if applicable. Adjust; clean the chain and use chain oil. Point 4.| | | |
Check steering head bearings for correct seat, if applicable. adjusting and greasing. Point 2.| | | |
Check and tighten buffer bearings. Point 3.| | | |
Check and adjust cable trains| | | |
Brake system functional test, if applicable. Adjust, check brake linings, see paragraph 1.| | | |
Check tyre air pressure and if necessary. correct| | | |
Load battery with the supplied charger| | | |
test drive after maintenance,Control of operational safety| | | |

Setting Brake System Front and rear wheel disc brake The optimum braking performance is achieved by adjusting the brake pads regularly.To do this, release the brake saddle from the bracket by releasing the two bus screws.

After the two mountings have been adjusted accordingly, the brake saddle can be mounted back on the bracket with the two inlet screws.

Service

If you have any questions or need spare parts and accessories, please contact your dealer or our online store at the following :

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>