Yale YRHCPZW4FM Wireless Module for Smart Door Locks Installation Guide

Yale YRHCPZW4FM Wireless Module for Smart Door Locks

Product Information

Specifications:

• Model: AYR-MOD-ZW3-MNL-0015 Rev A
• Manufacturer: ASSA ABLOY Residential Group
• FCC ID: MZR-YRHCPZW4FM
• ISED: 2676A-YRHCPZW4FM
• Compliance: FCC Part 15, CAN ICES-3B/NMB-3B

Product Usage Instructions

Adding a Device:

1. Open the Z-Wave system’s smart home or alarm app on your smartphone or tablet.
2. If Smart Start is enabled, follow the in-app prompts to add a new device. If not, proceed to steps 4-6.
3. For devices without Smart Start:
   • Enter the master entry code on your lock keypad followed by an icon.
   • Press the ‘7’ key followed by an icon.
   • Press the ‘1’ key followed by an icon.

Removing a Device :

1. Open the Z-Wave system’s smart home or alarm app and follow instructions for removing a device.
2. Enter the master entry code on your lock keypad followed by an icon.
3. Press the ‘7’ key followed by an icon.
4. Press the ‘3’ key followed by an icon.
5. Remove the Yale Smart Module from the slot above the battery compartment.

FAQ

• Q: What should I do if the network primary controller is missing or inoperable?
  A: Follow the provided instructions to add or remove devices manually using the Z-Wave system’s smart home or alarm app.

• Q: How do I know if Smart Start is enabled?
  A: Smart Start enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required, and the product will be added automatically within 10 minutes of being switched on in network vicinity.

• Q: Are there any safety precautions I should be aware of?
  A: Ensure to keep a minimum distance of 20cm between the radiator of the device and your body for FCC radiation exposure compliance.

Yale® Z-Wave® Plus 800 Series Smart Module Installation Guide
Please use this procedure only when network primary controller is missing or otherwise inoperable.

Adding a Yale Z-Wave® Smart Module to your Assure Lock & Z-Wave System

1.  Install Yale Smart Module into slot above battery compartment
   IMPORTANT: Batteries must be removed before inserting Yale Smart Module:

   • Remove battery cover
   • Remove batteries
   • Insert Yale Smart Module
   • Reinstall batteries
   • Reinstall battery cover

2. Open Z-Wave system’s smart home or alarm app on your smartphone or tablet

3. If you have Smart Start* enabled with your Z-Wave System follow in-app prompts to add a new device If you don’t have smart start or are not sure, follow steps 4 – 6

4. On your lock keypad, enter your master entry code followed by the icon

5. Press the 7 key followed by the  icon

6. Press the 1 key followed by the  icon

Removing a Yale Z-Wave® Smart Module from your Assure Lock & Z-Wave

System

1.  Open Z-Wave system’s smart home or alarm app and follow instructions for removing a device

2. On your lock keypad, enter your master entry code followed by the  icon

3. Press the 7 key followed by the  icon

4. Press the 3 key followed by the  icon

5. Remove Yale Smart Module from slot above battery compartment
   IMPORTANT: Batteries must be removed before removing Yale Smart Module:

   • Remove battery cover
   • Remove batteries
   • Remove Yale Smart Module
   • Reinstall batteries
   • Reinstall battery cover

6.  If you’re adding a new Yale Smart Module, follow instructions included with it SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in network vicinity.

Warning: Changes or modifications to this device, not expressly approved by ASSA ABLOY Residential Group could void the user’s authority to operate the equipment.

FCC

Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS.

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Industry Canada:

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotopically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

This Device complies with Industry Canada License-exempt RSS standard(s).
Operation is subject to the following two conditions:

1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
   • CAN ICES-3B/NMB-3B
   • FCC: MZR-YRHCPZW4FM
   • ISED: 2676A-YRHCPZW4FM

24/7 Tech Support : 1 -855-492-0505
Yale Locks & Hardware

• www.yalehome.com
• Yale® is a registered trademark of ASSA ABLOY Residential Group. Other products’ brand names may be trademarks or registered trademarks of their respective owners and are mentioned for reference purposes only.
  © Copyright 2020. All rights reserved. Reproduction in whole or in part without the express written permission of ASSA ABLOY Residential Group is prohibited.

References

• Smart Locks, Digital Locks, Digital Safes, Padlocks, Home Automation | Yale

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>