MiBOXER FUT042 RGB LED Strip Controller Instruction Manual
- June 6, 2024
- MiBOXER
Table of Contents
MiBOXER FUT042 RGB LED Strip Controller Instruction Manual
Features
This controller adopt the widely used 433MHz wireless technology with the features of low power consumption, long signal transmitting and strong anti- interference, etc. Widely used on the controlling of hotel lighting and home lighting.
-
RGB Color changing
-
Dimmable control
-
433MHz RF wireless transmission technology
-
Remote control
Control distance 30m
Parameters
Remote Control
- Working Voltage: 3V(2*AAA Battery)
- Working Temp.: -20~60°C
- RF: 433MHz
- Standby Power: 20uA
- Transmitting Power: <10mW
- Modulation Method: ASK
- Control Distance: 30m
Strip Controller
- Input Voltage: DC12V~24V
- Output: 6A/Channel
- Total Output: Max 12A
- Working Temp.: -20~60°C
- RF: 433MHz
- Control Distance: 30m
- Output Connection: Common anode
Products Key Diagram
-
Touch the color ring to change colors
-
Turn on or off the linked lighting device
-
Dynamic mode switching button
( See the dynamic mode sheet ) -
Switch button for color light and white light.
Note: If you want to change color under white light mode, you need to switch to color light mode. -
Under color light and white light, brightness +
Under dynamic mode，See the dynamic mode sheet -
Under color light and white light mode, brightness –
Under dynamic mode，See the dynamic mode sheet
Connect diagram
Pilot lamp instruction:
Always lighting means working normally; Flash means receiving remote signal
Note
Factory setting is one remote control one receiver. Users can group it as
per the need. One remote can control countless receivers,but one receiver just
can bel controlled by max 4 remotes.
Dynamic Mode Sheet
Press and adjust brightness and speed.
| Number | Dynamic Mode | Brightness | Speed |
|---|---|---|---|
| 1 | Change color automatically | Adjustable | |
| 2 | Three color jump to change | Adjustable | |
| 3 | Seven color jump to change | ||
| 4 | Three color gradual change | ||
| 5 | Seven color gradual change | Adjustable | |
| 6 | Red jumps to change | ||
| 7 | Blue jumps to change | ||
| 8 | Purple jumps to change | ||
| 9 | Green jumps to change | ||
| 10 | Yellow jumps to change | ||
| 11 | Cyan jump to change | ||
| 12 | White jump to change | Adjustable | |
| 13 | Red and blue flash alternately | ||
| 14 | Blue and green flash alternately | ||
| 15 | Red and green flash alternatively |
Linking the controller
-
Switch off the light, after 10 seconds switch on again.
-
When the light on, short press ” ” 1 time within 3 seconds.
The light blink 3 times slowly means the linking is done successfully.
If the light not blink slowly, the linking failed, Pls switch off the light again, and follow the above steps again.
Unlinking the controller
-
Switch off the light, after 10 seconds switch on again.
-
When the light on, short press ” ” 5 times within 3 seconds.
The light blinking 6 times quickly, means the unlinking successfully.
If the light not blink quickly, the unlink failed, pls switch off the light again, and follow the above steps to unlink again.
Attention
- Please check whether the input voltage of the constant voltage power supply is in accordance with the controller, and please check the connection of both the cathode and anode, otherwise the controller will be damage.
- Please don’t connect wires with power on. Please turn on again only when it is in right connection and no short circuit.
- Non-professional user cannot dismantle the controller directly, otherwise it may damage the controller.
- Please do not use the controller in the place with widely range metal area or strong electromagnetic wave nearby, otherwise, the remote distance will be seriously affected.
www.futlight.com
Made in China
