Actisense NDC-3-B NMEA Data Combiner User Manual
- June 6, 2024
- Actisense
Table of Contents
- Actisense™
- Notices
- Foreword
- NMEA Data Combiner – NDC-3-B
- General features
- Technical features
- Software updates
- Connecting devices together
- The different NMEA standards
- Connections
- Connecting to NMEA devices
- Other Connections
- Troubleshooting guide
- Specifications
- Company Information
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
NMEA Data Combiner
NDC-3-B
Issue 1.31
User Manual
-
Multiple talker interface for use with the NMEA 0183 standard.
Serial-data networking of marine electronic devices/instruments -
Personal computer (RS232) interface to NMEA 0183 standards
Actisense™
Important Notices
The Actisense™ NMEA Data Combiner (NDC-3) is intended for use in a marine
environment, primarily for below-deck use.
If the unit is to be used in a more severe environment, such use may be
considered misuse under the seller’s warranty.
The Actisense™ NMEA Data Combiner (NDC-3) has been certified to comply with the
European directive for ElectroMagnetic Compatibility (EN60945), and is
appropriately CE marked. The operation of the unit should be in conjunction
with appropriate CE-approved shielded connectors and cabling used in
accordance with the CE directive EN60945. Any EMC-related issues should be
reported to Active Research immediately to allow the company to rectify or
resolve EMC-related problems in accordance with its obligations under EN60945.
If the unit is connected such that compliance failure occurs beyond the
company’s control, the company shall not be held responsible for compliance
failure until suitable EMC guidelines for connection are seen to have been
taken.
Notices
When using this document, keep the following in mind:
The products described in this manual and the specifications thereof may be
changed without prior notice. To obtain upto-date information and/or
specifications, contact Active Research Limited or visit the Actisense™ website
(www.actisense.com).
Active Research Limited will not be liable for infringement of copyright,
industrial property right, or other rights of a third party caused by the use
of information or drawings described in this manual.
All rights are reserved: The contents of this manual may not be transferred or
copied without the expressed written permission of Active Research Limited.
Active Research Limited will not be held responsible for any damage to the
user that may result from accidents or any other reasons during the operation
of the user’s unit according to this document.
The NDC-3 does not validate the NMEA data it receives in any way. Neither the
NMEA sentence checksum nor the data contained within the NMEA sentence is
validated. Therefore, the electronic device(s) supplying the NDC-3 with NMEA
data retain(s) the sole responsibility for the NMEA data’s validity.
Foreword
Actisense™ recognizes that instructions are often skipped, so we have aimed to
write this document in an informative, yet direct manner that will aid the
user. We have tried to cover all the points a typical user may need to know.
Please read all sections before installing and using the Actisense™ NMEA Data
Combiner product and any related software programs.
Introduction The Actisense™ NMEA Data Combiner (NDC-3) product was developed
out of the requirement to solve two fundamental problems with the existing
marine industry NMEA 0183 communications standard.
In theory, the NMEA 0183 standard allows any suitably designed marine
electronic device to share its gathered information with any other device on a
vessel. Unfortunately, there is one very large drawback with this standard –
only one device on a connected network can actually send data (a single
talker), with multiple devices (determined by the current limit of the sending
unit) listening to that data (multiple listeners).
If the vessel owner has an instrument that ideally requires the data output of
two or more devices, for example, a chart plotter, then the owner has no
alternative but to settle on connecting only the most important device (that
which supplies the most used information), normally that is the GPS unit. All
other devices cannot be used. What happens if the owner prefers the vessel’s
gyro compass heading output to that of the GPS, or requires that the current
depth be displayed on the plotted chart to help avoid the possible case of
running the vessel aground on a shifting sand bank? The NMEA 0183 standard
cannot supply an answer to those questions as it can handle only one
transmitting device. These two elementary problems can be solved simply and
easily with the Actisense™ NMEA Data Combiner’s very flexible design approach.
Alternately, if the vessel has two or more identical NMEA devices (e.g. GPS’s
or depth sounders) the system solution could be to use the Actisense™ NMEA
Autoswitch. Full information on the complete Actisense™ product range can be
found on the Actisense™ website.
NMEA Data Combiner – NDC-3-B
General features
4 NMEA 0183 data input ports
Each NMEA 0183 input port has a priority level. This is fixed to the logical
order that matches the port numbers, i.e. port 1 has the highest priority and
port 4 has the lowest.
An NMEA 0183 data combined output port This output combines the input data
into one standard NMEA output. The NMEA inputs and output have the same baud
rate. This means that the output can only carry as much data as one of the
inputs – therefore the combined data from all four NMEA input channels could
exceed the data-carrying capacity of the NMEA output channel. The combiner
contains special software to ensure that when the output channel is
overloaded, new data of the same type as older data, still in the buffer, will
overwrite the older sentence. This will only happen when the output load
becomes too high and ensures that the combiner cannot build up excess old data
in the case where the output stream is fully loaded or overloaded.
A PC compatible RS-232 bi-directional port
A PC can use the RS-232 port to read all the NMEA data traversing through the
NDC. This allows for the possibility of a “virtual cockpit” of instruments
displaying all available data in any manner, the user requires (available from
a number of manufacturers).
Technical features
A high-speed micro-controller is capable of 10 million instructions per
second.
Flash ROM technology that supports automatic programming for quick and
easy updates, 10,000+ erase cycles and a 10-year Data Retention provides
carefree user configuration.
On-chip memory store allows buffering of short-term NMEA data, allowing
the unit to smooth short-term peaks in the NMEA data flow.
NMEA 0183 inputs are opto-isolated differential inputs to fully comply
with the NMEA 0183 standard specification. This allows the inputs to work
correctly with long cable runs and in a noisy environment. Typical operating
voltage s 2.0v to 15.0v. The unit can withstand +/- 35v continuously, and +/-
40v transients. The Opto-isolator can protect any upstream equipment (chart
plotter, laptop PC, radar etc.) from up to 2000v of the common-mode voltage
difference.
NMEA 0183 full-differential output driver. This can drive up to 15 fully
compliant NMEA 0183 device loads, with a 30mA (maximum) drive capability. The
full-differential output ensures better quality communications and lower noise
emissions on unshielded twisted pair cabling.
F ull specification RS232 interface ensures that any marine electronic
device (or PC) that has an RS-232 port receives all the input NMEA data, and
can add its own NMEA data to the combined output. This connection also allows
the unit to be updated via the free flash upgrade software that will be made
available on the Actisense™ website if the NDC-3 software has been enhanced.
Wide battery input voltage range to offer maximum compatibility, the NMEA
0183 NDC-3 can operate from a battery supply anywhere between 8 and 35 volts.
Low Power Consumption is typically 26-30mA at 12 volts and 16-18mA at 24
volts.
A diagnostic LED indicates the operation mode of the NDC-3 if any faults
have been detected, or the peak load currently on any one of the NMEA inputs.
Very tough Polycarbonate case is certified to IP66 (classified as “totally
protected against dust and protection against low-pressure jets of water from
all directions”). Being Polycarbonate, it is also incredibly strong, offering
a wide temperature range and superior protection to the electronics inside.
The IP66 rating of the case is only limited by the sealing gasket strip, which
can be enhanced by applying a suitable non-acid-based marine sealant to the
gasket after wiring and testing. This will allow use of the unit in areas
where salt spray could enter, accidental immersion may occur, or in
environments where maximum long-term reliability is paramount.
Robust Nylon grommets are certified to IP68 (classified as immersible for
long periods without water ingress). Note that to achieve this level of water
integrity all grommets must be occupied by round-section cables.
Large range of possible cable diameters of between 4.5 mm and 10 mm,
single or multi-pair wire types can be easily accepted.
Software updates
The NDC-3’s built-in firmware is held in “flash” memory, allowing quick and easy
upgrades using a simple Microsoft
Windows (95/98/ME/NT/2000/XP) user interface program (Flash Centre) running on
a connected PC.
It is our policy to provide these updates free on our website,
www.actisense.com, so that your combiner can
become more sophisticated with time, and should there be any bugs reported in
the software, they can be promptly fixed without the unit coming out of
commission. This upgrade can be performed with the unit completely in-situ,
via a PC connected to the RS232 port.
Actisense™
Connecting devices together
The basics
NMEA data is transmitted from an information source such as GPS, depth
sounder, gyrocompass, etc. These data sending devices are called “Talkers”.
Equipment receiving this information such as a Chartplotter, radar, or NMEA
display is called a “Listener”.
Unfortunately, only one Talker can be connected to a single NMEA 0183 system
at any one time. Two or more Talkers are simply not possible because they are
not synchronized to each other, and will attempt to ‘talk’ at the same time
(over each other), resulting in corruption of the NMEA data, and potentially
in disaster if valuable data such as navigation information is lost or
corrupted so that it is incorrect and/or misleading.
Actisense™ produces a full range of products to solve all NMEA interfacing
requirements.
Please visit the Actisense™ website for full details on these and other
Actisense™ interfacing, Depth sounding, and Sonar products.
The NMEA signals
The NMEA 0183 system v2.0 and later uses a ”differential” signaling scheme,
whereby two wires are used to transmit the NMEA data. These connections will
be labeled as either NMEA “A” and “B“ or NMEA “+” and “-“ respectively,
depending on the instrument and manufacturer.
When connecting between different manufacturers, there can be some confusion,
but it is simple and easy to remember: NMEA “A” connects to NMEA “+” and NMEA
“B“ connects to NMEA “-“.
The different NMEA standards
The NMEA 0183 specification has slowly evolved over the years, so connecting
one device to another is not always a straightforward matter. The earlier
versions of NMEA 0183 before v2.0, as detailed above), used slightly
different connection methods and signal levels: the instruments had just one
“NMEA” data line (‘Tx’ or ‘Out’), and used the ground as the other line –
similar to the way a computer serial port works. This connection method is
referred to as “single-ended” instead of the “differential” method used by
NMEA 0183 v2.0 devices.
The data format is largely the same between both systems, with v2.0 adding
some extra sentence strings, and removing older (redundant) sentence strings
from the specification. The situation is further complicated, as many
manufacturers still use the old (“single-ended”) method of connection because
it is cheaper to implement.
So how can an older type NMEA device be connected to a newer type device?
Care is needed – it is possible to damage or overload the output of a newer
differential device if it is incorrectly connected to an older device. This is
because the older devices used ground as the return, whereas the newer devices
actually drive the NMEA “-/B” line between 5v and 0v. Thus, connecting this
output to the ground will result in high currents being drawn by the driver
instrument, resulting in potential overheating and damage to the driver
circuits.
To connect a new type differential device to an old type single-ended system,
connect the NMEA “+/A” output from the differential driver to the single-ended
NMEA “Rx” or “In” input of the device. Leave the NMEA “-/B” output floating.
Connect the ground line of the differential output device to the ground of the
single-ended device. This provides the required data signal return current
path.
To connect an old type single-ended device to a new type differential device,
connect the NMEA ”Tx” or “Out” output from the single-ended driver to the
differential NMEA “+/A” input of the device. Connect the ground line of the
single-ended output device to the NMEA “-/B” input of the differential device.
This provides the data signal return
current path. If the NMEA “-/B” input is left floating, then data
corruption/errors may occur. Please refer to the Output Connections section
for an example of these connection methods.
Connections
The NMEA Data Combiner (NDC-3) has screw-terminal “Phoenix” type external connections for: –
-
Four NMEA 0183 inputs.
All NMEA 0183 inputs are of the differential optoisolated type and use the unique Actisense™ low current drain circuitry (2mA @ 2.0v) to conform in full with the NMEA 0183 marine electronic device network communication standard, and are flexible enough to interface to most fully and partially compliant devices. -
An NMEA (data combined) 0183 output. The NMEA 0183 output comprises of three connections: ‘+’, ‘-‘ and ‘Ground’ and conforms in full to the NMEA 0183 standard. This allows the NDC to interface to various different devices that require any combination of these outputs.
-
An RS-232 input/output.
The bi-directional RS-232 port is designed for direct connection to a Personal Computer (PC) or another marine device capable of interfacing to a standard RS-232 port. -
Battery supply input.
Note:
- To complete the NMEA 0183 standard all device interconnection NMEA cables used should meet the two-conductor, shielded, twisted-pair configuration specification. The shield connection of these wires should be connected at the instrument end only to prevent ground loops.
- Refer to the Specifications section for the full details on input/output specifications.
- If the laptop / PC to be used with the NDC does not have an RS-232 serial port available, the Actisense™ USB to RS-232 adapter cable has been tried and
tested to provide a compatible communications port. Please visit the Actisense™ website for full details on this and other Actisense™ products.
Connecting to NMEA devices
NMEA 0183 Inputs
The NMEA 0183 differential opto-isolated inputs are designed to handle a
variety of NMEA 0183 device output specifications. Please determine (from
device manufacturer’s information) if the device(s) required to be connected
to the Actisense™ NDC-3 conforms in full to the NMEA 0183 network
communication standard. If it does not, the flexible Actisense™ NDC-3 inputs
should still be capable of interfacing with the device, though this is not
guaranteed.
The diagram above shows a typical installation with both fully compliant NMEA
devices with differential inputs/ outputs, and non-differential output devices
that output NMEA using the ground line as the “NMEA -” line. NMEA Talker
devices 1, 2, and 4: These devices conform in full to the NMEA 0183 standard.
Devices 1 and 4 share the same connection ID’s as the
Actisense™ NDC, so the connection is a simple matter of matching the IDs
(refer to figure 2). Device 2 uses the RS485 convention connection IDs. Simply
connect ‘A‘ to ‘+/A‘ and ‘B’ to ‘ -/B’ (refer to figure 2).
NMEA Talker device 3: This device does not conform completely to the NMEA 0183
standard. However, by connecting ‘+‘ to ‘+/A‘ and its ‘G/Ground’ to the NDC
“-/B” the NDC should be able to receive the NMEA data correctly.
NMEA 0183 Output
The NMEA 0183 buffered output is capable of driving up to 15 NMEA 0183 fully
compliant listening devices, or a mixture of NMEA 0183 devices and a Personal
Computer (PC) communication port.
NMEA Listener device’s B and C: These devices conform in full to the NMEA 0183
standard and their connection IDs match that of the NDC.
Personal Computer: Whilst the RS-232 port is designed for connection to a PC,
the NMEA 0183 output is also capable of being read by most PCs. Simply connect
‘+’ to ‘Rx’ and ’G’ to ‘Gnd’ on a standard D-type (probably male) connector.
NMEA Listener device A: This device does not conform in full to the NMEA 0183
standard. However, by connecting ‘-‘ to ‘-/B‘ and ‘G/Ground’ to ‘And’ the
device should be able to receive the NMEA data correctly, though this is not
guaranteed.
Note: 1. Wire colors are for guidance only.
Other Connections
Connecting to a Personal Computer
The RS-232 port can be connected to a PC communications port using a cable
conforming to the following specification:
- A D-type female (socket) connector for the PC end of the cable
- A minimum of 3 cores are required in a shielded cable. The higher quality cable will naturally yield higher performance / higher Signal-to-Noise Ratio (SNR). Most typical cables have two twisted pairs inside. In this case, use one pair for the TX line and one for the RX line. Use the spare wire in each pair as ground, and connect the cable shield to the ground only at the computer end.
- The TX of the NDC-3 should be connected to the RX of the computer (standard D-type, pin 2), and the NDC-3 RX should be connected to the TX of the computer (pin 3). The GND of the NDC-3 should be connected to the PC’s serial port ground (pin 5).
Connecting to the battery supply
The Actisense™ NDC-3 should be wired to the vessel’s battery supply in the
most direct manner possible, to minimize interference from other electronic
devices. The cable used should be of sufficient gauge to handle the power
requirements of the Actisense™ NDC-3 (refer to the Specifications sections).
Note:
1. Wire colors are for guidance only.
Troubleshooting guide
This guide will concentrate on all relevant troubleshooting issues above simple cable connection faults. Therefore, the cables between the NDC-3 hardware and any other devices should be checked as a matter of course, before continuing with this guide.
Diagnostic LED
The NDC-3 hardware supports a tri-color diagnostic LED that indicates the
current operating mode of the hardware, or if an error has been detected
during the self-test initiation process. Table 1 details what each LED colour
represents and if any user interaction is required.
LED Colour I
Flash Count| Mode I Error condition| | Required user response
---|---|---|---
| Normal operation modes| The sequence below indicates a successful power-up
of the NDC-3 and the commencement of data combining.
Red, No flashing| Start-up mode, No error| No response required. A normal
operation mode that should last for no more than 1.5 seconds. Any longer
indicates an error with the main program.
Red, No flashing| Flash updating mode, No error| No response is required. LED
will stay red for the duration of the flash update operation (using Flash
Centre). Once the operation is complete, NDC hardware will be automatically
reset.
Amber, No flashing| Initialize and self-test mode,
‘
No error| response required. A normal operation mode that follows after the
Start-up mode and should last for approximately 1 second.
Green, No flashing| Normal and no data mode,
No error| No response is required. A normal operation mode that follows the
Initialise and self-test mode. Indicates that no error was detected during the
self-test operation.
Also indicates that no data is currently being received by the NDC-3 hardware.
Green, Flashing
(1-10 per second)| Normal and data Rx mode
‘ No error| No response is required. A normal operation mode indicates that
data is currently being received (on at least one channel) by the NDC-3
hardware. Flash rate proportional to Rx rate.
| Error conditions| If the error persists the NDC-3 unit should be returned to
Actisense TM (refer to the Contact Information section).
Amber, Flashing
(Once every 4
seconds)| Error trap mode,
EEPROM memory error| An error with the EEPROM memory has been detected during
the self-test mode.
Reset the NDC-3 hardware.
Specifications
Parameter | Conditions | Min. | Max. | Unit |
---|
Supply
Supply voltage| | 8| 35| V
Supply current (see note 1)| Supply voltage = 12v| 26| 30| mA
Supply voltage = 24v| 16| 18| mA
NMEA
Input voltage between +/-| Logical ’17stop bit| –15.0| 0.5| V
Logical ’07start bit| 4.0| 15.0| V
Input current| Maximum is under +35v overload condition| 2.0| 30| mA
Differential input voltage| Required level for NMEA to be detected| 2.| 2.0| V
Output voltage between +/- and ground (see note 2)| Logical ‘1’/stop bit| 0.0|
0.5| V
| 5.| 5.| V
Output current (see note 2)| At maximum load, drive voltage reduces to 2v| –|
32| mA
Output short circuit current.| | 50| 55| mA
Baud rate – fixed (see note 3)| | | 5.| kbit/sec
Data propagation delay| | 1.0| 100| ms
RS-232
Input voltage range| | -15| +15| V
Input voltage threshold| LOW| 0.8| 1.| V
HIGH| 2.| 3.| V
Output voltage swing| Loaded with 3K.S2 to Ground| ±5| ±9| V
Output resistance| (RS232 Vout = ±2v)| 300| | Ohms
Output short circuit current (Infinite duration)| | | ±18| mA
Baud rate (see note 4)| | | 38.| kbit/sec
Data propagation delay| | 1.0| 100| ms
General
Ambient temperature| -20| 70| °C
Table 2 – NDC-3 specifications
All specifications are taken with reference to an ambient temperature (TA ) of
+25°C.
Note:
- Current consumption measured under no-load conditions
- NMEA output is RS-485 compatible.
- NMEA 0183 inputs and outputs on the NDC-3 are fixed to 4800 baud
- RS232 baud rate is fixed at 38400 baud on the NDC-3
Company Information
Active Research Limited
5, Wessex Trade Centre
Ringwood Road
Poole
Dorset
UK
BH12 3PF
Telephone: 01202 746682 (International : +44 1202 746682)
Fax: 01202 746683 (International : +44 1202 746683)
Actisense™ on the Web: For advice, support, and product details
E-mail: support@actisense.com
Website: www.actisense.com
Active Research on the Web: For specialist consultancy and customization
E-mail: support@activer.com
Website: www.activer.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>