ecobee EBSCV01 Smart Control with Voice Control User Guide
- June 6, 2024
- Ecobee
Table of Contents
Smart Control with Voice Control
User Guide
See what your SmartCamera can do for you
| Balances privacy and clarity by automatically turning off when family
members are around and on again when the house is empty.
---|---
| Helps you check in with real-time conversations through your mobile
device and smart camera.
| Provides a full view of the home by letting you pan and tilt to view
images from the mobile app.
| Keeps you informed with notifications for anything that requires your
attention or for the moments that matter.
For details on these features and to discover new ones, go to ecobee.com /smartcamera-features
Open the ecobee mobile app to get started
Once you’ve opened the app, add your SmartCamera to begin setup. Find out more at ecobee.com/setup
Meet your SmartCamera
Top view | Front view |
---|
|
Pick a view from any angle
You can use the dual stand/mount for both placing or wall-mounting your
SmartCamera.
Once mounted, you can angle the camera to change the field of view.
How to mount your SmartCamera
-
Attach the mount
Attach the dual mount/stand to the back of the smart camera and plug it in so you can test the view in the next step.
-
Test view
Hold the camera up to the place you’d like to mount it and check the view on the ecobee app.
You can adjust the view after mounting.
-
Drill hole
Use a 3/16” drill bit to drill a hole where you will mount the camera.
-
Screw-in anchor
Screw the plastic anchor into the wall and ensure it’s flush.
-
Fasten the screw
Fasten the mounting screw into the anchor until there’s a little amount of space between it and the anchor.
-
Hang the mount on the screw
Remove the mount from the camera and hang it on the screw. If it feels too loose, adjust the screw until it’s secure.
-
Attach the camera to the mount
Attach the camera to the mount and make sure it’s secure.
-
You’re all set
Open the ecobee app to check the camera’s view and adjust it any way you’d like.
Approvals
This product was designed and built in accordance to RoHS directive 2011/65/EC
and contains no hazardous substances as defined by this directive.
FCC Compliance Statement | Compliance Notice:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Change or modifications that are not expressly approved by the manufacturer could void the user’s authority to operate the equipment.
RF Exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 8 inches during normal operation.
Innovation, Science and Economic Development Canada (ISED) | Compliance
Notice:
This device contains license-exempt transmitter(s)/ receiver(s) that comply
with Innovation, Science, and Economic Development Canada’s license-exempt
RSS(s).
Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
RF Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This transmitter must be installed to provide
a separation distance of at least 8 inches from all persons and must not be
collocated or operating in conjunction with any other antenna or transmitter.
FCC ID: WR974100118120 IC: 7981A-74100118120 Model: EBSCV01
Warning: Changes or modifications not expressly approved by ecobee Inc.
could void the user’s authority to operate the equipment. This product is not
designed for use outdoors. Improper installation may void the warranty. Not
for children under 3 years.
Legal Notice
The use of the HomeKit™ logo means that an electronic accessory has been
designed to connect specifically to iPod®, iPhone®, or iPad®, respectively, and
has been certified by the developer to meet Apple® performance standards. Apple
is not responsible for the operation of this device or its compliance with
safety and regulatory standards. Please note that the use of this accessory
with iPod, iPhone, or iPad may affect wireless performance. Apple, iPhone,
iPad, and iPod touch are trademarks of Apple Inc., registered in the U.S. and
other countries. HomeKit is a trademark of Apple Inc.
Warning: Choking hazard. Not for children under 3 years.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>