OLYMPIA NC 450 Money Counter Machine User Manual

OLYMPIA NC 450 Money Counter Machine

Operating Manual

• Please read and observe the following information and keep the operating manual available for future reference!

Safety Information
WARNING!

• Risk of suffocation through small parts, packaging and protective foil!
• Keep the product and packaging out of reach of children!

CAUTION!

• Risk through infeed rollers!
• Keep fingers, hair etc. away from the infeed.
• Risk of tripping due to improperly laid cable!
• Lay cables so that people cannot trip over them.

ATTENTION!

• Risk of property damage!
• Ensure no foreign bodies, such as paper clips, rubber bands, etc. get into the infeed.
• Prevent exposing the device to environmental influences such as smoke, dust, vibration, chemicals, moisture, heat or direct sunlight.
• Repairs may only be carried out by appropriately trained specialists.

Intended Use

The banknote counter with validation functions, subsequently referred to as a banknote counter, serves to count bank notes. Any other use is considered unintended use. Unauthorised modification or reconstruction is not permitted. Under no circumstances open the machine or complete any repair work yourself. This device checks two of the features of the bank notes (ultraviolet feature and magnetic feature) to ensure they are not counterfeit. If other features of the notes have been falsified or are missing, this device cannot detect the notes as being critical. In the same way, an authentic banknote can be detected as being faulty due to soiling or some other external influence. Therefore, test bank notes detected as being faulty several times and, in the case of doubt, consult your bank institution.

Only Use in Suitable Conditions
Prevent exposure to smoke, dust, vibration, chemicals, moisture, heat and direct sunlight.

Scope of Delivery

• NC 450 banknote counter
• External display
• Power cable
• 2 drive belts (spare part)
• Spare fuse
• Screwdriver
• Brush
• Operating manual

Display and Notation

• Action to be completed
• The result of the Action
• Helpful information

Operating Elements

1. 1 or move upwards in the menu settings

2. 4 or SET to open the menu settings or move one level further

3. 2 or MG to activate/deactivate the magnetic test

4. 5 or BATCH to process batches

5. 3 or UV to activate/deactivate the ultraviolet test

6. 6 or ADD to activate/deactivate the add function

7. 0

8. AUTO/MANUAL to switch between automatic and manual start

9. 7 or move downwards in open the menu settings

10. 8 or COUNT to activate Counting without sensors

11. RESTART
    Display
    The diagram illustrates the display during the power-on self-test. Some of the features illustrated do not belong to the functional range of this banknote counter.

12. The magnet sensor is activated

13. The ultraviolet sensor is activated

14. Top Display

15. Quantity

16. The batch function is activated

17. The add function is activated

18. Count without sensors is activated

19. Settings

20. The manual start is activated

21. Automatic start is activated

22. Bottom display
    Operation
    Switching the Bank Note Counter On/Off The bank note counter is switched on and off using the switch on the rear of the machine. If the machine will not be used for a longer period, disconnect it from the power outlet.

23. On

24. Off

25. Mains power connection

26. Connection socket for external display

After switching the machine on, it performs a self-diagnosis. During the self- diagnosis. appears in the display. When the self-diagnosis has finished without any errors, X0 appears in the display.

• If an error is detected, it is indicated in the top display (refer to the Error table) and the background turns red.

Validation Tests

• The best results are achieved after a warm-up phase of 3 minutes.
• Bright ambient light can affect the sensor and falsify results.
• Before inserting the bank notes, select which features (magnetic and/or ultraviolet) you want to test.
• Press the MG button.
• The magnet sensor used to detect the magnetic ink is activated/deactivated. When activated, the sensor is indicated in the display. When activated, the sensor is indicated in the display.
• Press the UV button.
• The ultraviolet sensor for detecting UV light is activated/ deactivated. When activated, the sensor is indicated in the display.
• Preparing Bank Notes Pay attention to the following points to prevent malfunctions.

• Check the batch of banknotes for paper clippings, paper clips, rubber bands and other foreign bodies (A) and remove them before inserting the bundle in the machine.
• Do not insert any damaged bank notes (B).
• Smooth any creased and folded bank notes before inserting them (C/D).
• Do not attempt to count notes that are too thick or hard items.
• Fan out the bank notes to separate them prior to insertion.

Inserting Bank Notes

• Slide and fan the bank notes in the bundle so that the top banknote is somewhat lower than the one following. Insert the bank notes in the infeed tray (A). Or
• Insert the bundle vertically in the infeed tray and guide the bundle to the rear so that the bank notes shift against each other (B).
• The counting process starts up automatically if the automatic start function has been activated (AUTO appears in the display).
• Bank notes which have been inserted incorrectly, as illustrated in C and D, lead to an improper count or a malfunction.
• Since the security features of banknotes are provided on both sides, the process for detecting counterfeit banknotes is performed reliably on both sides.

Functions

Counting

• This function counts the number of banknotes and, depending on the sensor setting, their validity.
• During the counting process, the quantity of banknotes appears in the top display.
• When the bank notes counted are removed from the output tray, the quantity count in the top display is reset to X0 and the bottom display displays the quantity.

Adding
If several bundles of bank notes are stacked in the infeed tray one after the other, counting continues even if the bank notes already counted are removed from the output tray.

• Press the ADD button
• The Add function is activated/deactivated.

Batch
This function causes counting to stop when the preset quantity of banknotes has been counted. If the counted batch of banknotes is removed from the output tray, the display is reset to X0 and the next batch is counted.
The quantity of bank notes can be set to any number between 1 and 999. The preset quantity appears in the bottom display.
If the infeed tray becomes empty before reaching the preset quantity, BATCH flashes in the display. When more bank notes are inserted in the infeed tray, the process is resumed.

Press the BATCH button.

• BATCH flashes in the display. The preset quantity of 100 appears on the bottom display.
• Use the digit buttons to enter the quantity you want to be counted.
• The quantity entered appears in the bottom display.

Sorting

• With this function, which is always activated, the first banknote is used as a reference for those following. If the machine detects a banknote that deviates from the reference note, the machine stops. d appears in the display, the background of which turns red. The deviating bank note can be removed.
• Whether the removed banknote should be counted or not can be defined in the settings (refer to Settings).

Settings
The sensitivity of the sensor and other parameters can be modified using the respective Settings function.

• Press the SET button for a few seconds until the acoustic signal stops.
• d05 and C5 100 appear in the display. d05 represents the current value of the memory segment C5 100. You can change the value using the arrow buttons.
• Press the SET button again.
• The next memory segment appears together with the value.
• After pressing the SET button for the last memory segment you exit from the Setting function.

The table below contains the default settings and functional assignments of the memory segments.

The higher the value, the lower the sensitivity

C5 200| d05| MG-sensitivity| Setting range 0 – 9

The higher the value, the lower the sensitivity

C5 300| d05| Detection of double banknotes| Setting range 0 – 9

The higher the value, the lower the sensitivity

C5 400| d09| Brake| Setting range 0 – 9

The higher the value, the higher the sensitivity

C5 500| d09| Counter wheel| Setting range 0 – 9

The higher the value, the higher the sensitivity

C5 600| d08| Transportation| Setting range 0 – 9

The higher the value, the lower the sensitivity

C5 700| d08| (Internal function)| (Do not change)
C5 800| d01| (Internal function)| (Do not change)
C5 900| d00| (Internal function)| (Do not change)
C5 A00| d01| Count / Do not count bank notes which have been sorted out.| d01: Count

d02: Do not count

C5 b00| d02| (Internal function)| (Do not change)
C5 C00| d00| (Internal function)| (Do not change)
C5 d00| d02| Detect size differences of the bank notes| Setting range 0 – 9

The higher the value, the lower the sensitivity

C5 E00| d08| (Internal function)| (Do not change)
C5 F00| d04| (Internal function)| (Do not change)

To reset the machine to its default settings, press the
RESTART button while switching the machine on.

Clearing Errors
Errors are indicated in the display by an error code and the display background turning red.

A frequent source of errors is the soiling of the sensors (see Cleaning the Sensors).

notes from the batch.

Check the sensitivity setting of the UV sensor.

b| Too little or no magnetic reaction from the banknote.| Remove critical notes from the batch.

Check the sensitivity setting of the MG sensor.

C| Bank notes were detected as being chained.| Check whether the bank notes stick together and count the batch again.
F| Bank notes as half bank notes.| Remove critical notes from the batch and check for signs of damage.
E01| Banknote count sensor| Clean the sensor for counting the notes or replace it with a new one.
E03| Coding disk sensor| Clean the sensor for the coding disk or replace it with a new one.
E04| Infeed tray sensor| Clean the sensor for the infeed tray or replace it with a new one.
E05| Output tray sensor| Clean the sensor for the output tray or replace it with a new one.

Maintenance

Cleaning the Sensors

• Bank notes are often soiled, particularly by dust. The dirt deposits on the sensors during the counting process. Soiled sensors are the most frequent cause of malfunctions.

• Clean the sensors with the brush supplied. Open the banknote counter to clean the sensors. How to open the bank note counter is described in the following steps.

• Grip the bank note infeed at the sides and remove the infeed vertically out of the machine. Do not grip the infeed in the middle section.

• Pivot the grip to the rear.

• Pivot the operating panel to the front.

• Clean areas which cannot be accessed using compressed air, if necessary. Compressed air can be obtained in small aerosol cans.

• Clean the sensors with the brush supplied.

• Close the machine in the reserve sequence after cleaning.

Adjusting the Pressure of the Infeed Plate
The bank note counter is set up at the factory to draw the bank notes in properly. If bank notes are no longer drawn in properly, adjust the pressure exerted by the infeed plate.

• The adjusting screw to alter the pressure exerted by the infeed plate is located at the rear.

• 28 Adjusting screw
• 29 Locking screw

The adjusting screw is secured against being adjusted inadvertently by means of a locking screw.

• Switch the banknote counter off.
• Loosen the locking screw using the screwdriver supplied.
• Adjust the pressure of the infeed plate so that the bank notes can be pushed under the rubber rollers by exerting a little force.
• Tighten the locking screw.

Technical Data

start

Batch function, up to 999 banknotes can be selected

Addition function

Validation test| Ultraviolet and magnetic features test
Sensor sensitivity| Adjustable in 9 levels
Capacities: infeed and output trays| 100 old banknotes, 200 new banknotes
Size of countable banknotes| 50 mm x 110 mm bis 90 mm x 185 mm
Counting speed| 1,000 banknotes / minute
Power supply| 230 V/ 50 Hz
Power consumption| 75 W
Dimensions| 306 mm x 247 mm x 185 mm
Weight| 5.5 kg

Maintenance Tips

• Clean the housing surfaces with a soft, fluff-free cloth.
• Clean the sensors after each use.
• Clean the sensors with the brush supplied.
• Do not use any cleaning agents or solvents.

The CE Mark on the device confirms conformity. The Declaration of Conformity can be read online at www.go-europe.com.

Disposal

• The adjacent symbol indicates laws dictate that electrical and electronic apparatus no longer required must be disposed of separate from domestic waste. Dispose of your device at a collection point provided by your local public waste authority. Packaging materials must be disposed of according to local regulations.
• Observe the identification of the packaging materials during the waste sorting process; they are identified by abbreviations (b) and numbers (a) which have the following significance: 1–7: plastic/20–22: paper and cardboard/ 80–98: composite materials.
• The packaging is made of environmentally friendly materials that you can dispose of at local recycling points. Advice on the options with which to dispose of your old device can be obtained from your municipal or local administration offices.
• Packaging materials must be disposed of according to local regulations.

The device and the packaging material can be recycled, so sort them prior to disposal for better waste management. Contact your local authorities for information on the various options available to ensure correct disposal. The logo is only applicable to Italy.

The device and packaging materials can be recycled; sort them for disposal to simplify waste management. The Triman logo is only relevant for France.

Warranty

Dear customer,

• we are delighted that you have chosen this equipment.
• In the case of a defect, please return the device together with the receipt and original packing material to the point of sale.

CONTACT

• GO Europe GmbH
• Zum Kraftwerk 1
• 45527 Hattingen
• Germany
• www.go-europe.com.

References

• Que Faire de mes Déchets ? Découvrez les solutions pour tous vos déchets et nos conseils pour en produire moins.
• Ihr zuverlässiger Partner für Bürotechnik aus Hattingen.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>