POWERQI LC26C Magnetic Desktop Stand Wireless Charger User Manual

Product Colaur, Material & Finishing Specfications
Desktop Magnetic
Wireless Charger
User Manual

Product Model| LC26C| Brand| | Part number|
---|---|---|---|---|---
Product Type| | Description| /| Job No.|
Dimension| 65*85mm| Original Designer| | Date| 2021.10.15
Scale| 1:1| Technology| 105g| Verifying|
Revision| 1.1| Change description| 2021.06.29

Thank you for using this product! This product is a Magnetic desktop stand wireless charger, supports iPhone 12 series devices/Airpods simultaneous charging. The product has a dedicated charging position for iPhone and Airpods, which can ensure the device’s wireless charging starts at the moment of contact. It can get rid of the limitation of complicated route connection and connection distance, so that users can enjoy the fun of wireless charging of digital products. Before using the Magnetic desktop wireless charger, please read this manual carefully and keep it for future reference.

Connect to Adapter

1. Connect the power adapter to the socket.
2. Type-C cable one interface connected to the power adapter, the other interface to the magnetic desktop wireless charger.

Note: This product is also compatible with USB-A to USB-C cables. Only QC2.0 & QC3.0 or PD standard power adapter supports this product’s quick charge function. USB-A to USB-C cable and power adapter need to buy separately.

Method of Application

When the wireless charger is connected to an ordinary 5V adapter through Type-C to Type-C cable (Standard cable for this product) or USB-A to USB-C cable, the product works in ordinary wireless charging mode and only supports a single 5W load. If you use QC, PD standard adapter, the product will work in quick wireless charging mode and supports 7.5W/ 10W/15W load. Recommendation: Use adapters of 20W and above.

Charging Diagram

1. Power on: After the blue indicator light flashes for ls, the green indicator light flashes for ls, then the blue and red lights are on at the same time, and then the green light stays on to enter the standby mode.
2. Standby: the indicator light is always green.
3. Charging: the indicator light will stay blue, remove the receiver, the indicator light will turn green, and enter the standby mode.
4. Charging Full: the indicator light is steady green.
5. FOD and abnormal: blue light flashes.

Notes

1. Do not squeeze or collide.
2. Do not disassemble or throw into fire or water, to avoid causing a short circuit leakage.
3. Do not use wireless chargers in severely hot, humid or corrosive environments,to avoid circuit damage and occurs leakage phenomenon.
4. Do not place too close with magnetic stripe or chip card (ID card, bank cards,etc.)to avoid magnetic failure.
5. Please keep the distance at least 20cm between implantable medical devices(pacemakers, implantable cochlear,etc.)and the wireless charger, to avoid potential interference with the medical device.
6. To take care of the children, to ensure that they won’t play with the wireless charger as a toy, to avoid unnecessary accidents.

Specification

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement: The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance between 20cm of the radiator of your body.
FCC ID: 2AFP2LC26C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>