HYPERGEAR HBT03 Vibe Wireless Headphones User Manual
- June 6, 2024
- HyperGear
Table of Contents
HYPERGEAR HBT03 Vibe Wireless Headphones User Manual
SPECIFICATIONS
- Volume Up/Next Track
- Play/Pause
- Volume Down/Previous Track
- LED Indicator
- USB-C Charging Port
- Auxiliary Input
- Microphone
INSTRUCTIONS
Fully charge your headphones before first use
HOW TO CHARGE
Connect to a USB power source using the included USB-C charging cable.
HOW TO PAIR
When you power your headphones on the LED will flash BLUE and RED to indicate pairing mode.
-
Using the Bluetooth menu on your device (phone, tablet, etc.), enable searching for nearby Bluetooth devices.
-
Select “ HyperGear VIBE” to connect and pair.
NOTE: If your device prompts for a PIN code, enter “0000”. -
Once paired, the LED will flash BLUE and you will hear a tone confirming the successful connection.
PLAY VIA AUX
Use a 3.5.mm auxiliary cable lo connect the headphones to other audio sources
including non Bluetooth devices. Your music will automatically
piny.
NOTE: When wired via AUX, the headphones power off to save battery and Bluetooth functions are automatically disabled. Use the controls on your source device instead,
FCC Compliance Notice
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FUNCTIONS
Multifunction (MFB)
Power On : Press & Hold (2 sec)
Power Off : Press & Hold (4 sec)
Play/Pause : Press lx
Answer/End Call : Press lx
Reject Call : Press & Hold (2 sec)
Redial Call : Press 2x
Activate Voice Assistant : Press 3x
- Remote functions may vary depending on phone models.
Need help? Visit www.myhypergear.com for additional product information or email info@myhypergear.com
IMPORTANT
Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in damage, excess heat, toxic fumes, fire, explosion, electrical shock or other hazards causing serious and/or fatal injury and/or property damage and not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.
- Do not store the device in a depleted state. Battery cells may be damaged. Charge your unit at least once every 3 months even when not in use.
- Permanent hearing loss may occur if you listen at high volumes. Set the volume to a safe level.
- Do not store at extreme temperatures (below 40°F or above 90°F).
- Recharge your device with the included USB-C charging cable or a certified 3rd party cable and a 2A charging adapter. Standard cables and adapters may charge the battery too slowly and damage /overheat the battery or cause a fire hazard.
- Do not attempt to modify, disassemble, or repair this product.
- Avoid excessive drops, bumps, and abrasions. If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
- If you find this product rapidly increasing in temperature, emitting odor, deformed, abraded, or demonstrating an abnormal phenomenon, discontinue use immediately.
- Disposal of the unit in the garbage is unlawful under state and federal environmental laws and regulations.
Contact info@myhypergear.com to submit a warranty claim. Proof of purchase is required.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>