HYPERGEAR 15642 Gravity Wireless Fast Charge Mount User Manual

June 6, 2024
HyperGear

HYPERGEAR -logo

GRAVITYWIR
WIRELESS FAST CHARGE MOUNT

HYPERGEAR 15642 Gravity Wireless Fast Charge Mount -

User Manual

IMPORTANT

Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in hazards, injury, and/ or property damage that is not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.

  1. Use only a certified 18W or QC 3.0 adapter to power this device. Standard adapters may damage the charger or cause a fire hazard.
  2. Do not place metal objects, magnets, magnetic stripe cards, and hard-drive-based devices near the wireless charger. It may cause data corruption.
  3. Do not attempt to modify, disassemble, or repair this product.
  4. Do not expose to water, moisture, or extreme temperatures (below 40°F or above 90°F).
  5. Under any circumstances, if you find this product rapidly increasing in temperature, emitting an odor, or demonstrating an abnormal phenomenon, discontinue use immediately.

HYPERGEAR 15642 Gravity Wireless Fast Charge Mount
-important

Phone cases that contain metal, magnets, or are thicker than 3mm will interfere with wireless charging.
NOTE: This charger is designed for Qi-compatible devices. If your phone does not have built-in Gi wireless charging capabilities, please use a certified Qi wireless charging case or receiver. Refer to your phone’s user manual for detailed features and functions.

SPECIFICATIONS

HYPERGEAR 15642 Gravity Wireless Fast Charge Mount
-input

  1. Charging Surface
  2. 2-Step Locking Lever
  3. Suction Moun
  4. Extendable Foot

HYPERGEAR 15642 Gravity Wireless Fast Charge Mount
-cable

ASSEMBLY

Place the locking ring over the 360° ball. Firmly press the mount head onto the ball. Pivot to your desired viewing angle then twists the ring until it is secured.

INSTALLATION VENT

  1. Squeeze the button on the base. Firmly slide the mount onto the air vent. Release the button once it’s secure.

DASHBOARD

  1. Remove the protective liner from the suction. Position on the dashboard as desired. Push down TWICE on the locking lever to secure the mount.

WINDSHIELD

  1. Place the suction on your desired location. Push down TWICE on the locking lever to secure the mount.

NOTE: If needed, rinse the suction cup with water and air-dry to restore stickiness.

INSTRUCTIONS

  1. Use the included USB-C cable to connect the wireless charger to the USB port labeled “Wireless Charger” on the car charger.
    NOTE: This device requires the use of the included car adapter. Standard 1A or 2A adapters are not powerful enough for this charger and may cause it to malfunction or overheat.

  2. Place your phone onto the cradle. The arms will tighten automatically.

For Larger Phones

  1. Pull down firmly – until you see the hole – to extend the foot completely.
  2. Adjust to the height needed to center your phone on the charging area. Your phone will Indicate when it Is positioned correctly when charging begins.

LED State
Standby
Charging
Foreign Object Detected
It’s normal for a wireless charger and your device to become warm while charging.
Need help? Visit www.myhypergear.com for additional product information or email info@myhypergear.com

FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. During the operation of the device, a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.

Contact info@myhypergear.comto submit a warranty claim. Proof of purchase is required.
     www.myhypergear.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals