15259 HyperGear Fabric Bluetooth Speaker User Manual
- June 5, 2024
- HyperGear
Table of Contents
User
Manual
15259 HyperGear Fabric Bluetooth Speaker
- Volume Down
- Volume Up
- Previous Track
- Next Track
- Audio Mode Play/Pause Answer/End Call
- LED Indicator
|
- Microphone
- On/Off — Long Press (3 Sec)
- Micro USB Charging Port
- AUX Input
- Micro SD Card Slot
- USB Input
---|---
SPECIFICATIONS
Speaker Output: 8W
Battery Capacity: 1500mAh
INSTRUCTIONS
Fully charge your speaker before first use
How to Charge
Connect to a USB power source using the included Micro USB charging cable.
Charging
Fully Charged (approximately 3 hours)
How to Pair
When you power your speaker on for the first time, the LED will flash
BLUE to indicate pairing mode.
-
Using the Bluetooth menu on your device (phone, tablet, etc.), enable searching for nearby Bluetooth devices.
-
Select “HyperGear Fabrix 2” to connect and pair.
NOTE: If your device prompts for a PIN code, enter “0000”. -
Once paired, the LED will turn solid BLUE and you will hear a prompt confirming the successful connection. You will hear a tone confirming the successful connection.
NOTE: The speaker will automatically reconnect to the last paired
Bluetooth audio device when the unit is turned on
How to Switch Between Audio Sources Press & Hold the Mode Button (2 sec) to
switch between playing via Bluetooth, AUX, Micro SD Card and USB as needed.
Play via Aux Use the included 3.5mm auxiliary cable to connect the speaker to
other audio sources including non-Bluetooth devices. Your music will
automatically play. Control the playlist and calls from your source device.
How to Switch Between Audio Sources
Press & Hold the Mode Button (2 sec) to switch between playing via
Bluetooth, AUX, Micro SD Card, and USB as needed.
Play via Aux
Use the included 3.5mm auxiliary cable to connect the speaker to other audio
sources including non-Bluetooth devices. Your music will automatically play.
Control the playlist and calls from your source device.
Play via Micro SD
Firmly inserts the Micro SD card. Your music will automatically play.
Play via USB
Firmly inserts the USB Flash Drive. Your music will automatically play.
Need help? Visit www.myhypergear.com for additional product information or email info@myhypergear.com
IMPORTANT
Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in damage, excess heat, toxic fumes, fire, explosion, electrical shock or other hazards causing serious and/or fatal injury and/or property damage and not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.
- Do not store the device in a depleted state. Battery cells may be damaged. Charge your unit at least once every 3 months even when not In use.
- Permanent hearing loss may occur if you listen at high volumes. Set the volume to a safe level.
- Maintain volume levels that will allow you to hear sounds around you and be alerted to potentially hazardous situations.
- Unit is IPX4. Do not submerge or expose to corrosive materials. Do not clean with harsh chemicals, soaps or detergents.
- Do not store at extreme temperatures (below 40° F or above 90° F)
- Recharge your device with the included Micro USB charging cable or a certified 3rd party cable and a 2A charging adapter. Standard cables and adapters may charge the battery too slowly and damage/overheat the battery or cause a fire hazard.
- Do not attempt to modify, disassemble, or repair this product.
- Avoid excessive drops, bumps, and abrasions.
- If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
- If you find this product rapidly increasing in temperature, emitting an odor, deformed, abraded, or demonstrating an abnormal phenomenon, discontinue use immediately.
- Disposal of the unit in the garbage is unlawful under state and federal environmental laws and regulations.
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Contact info@myhypergear.com to submit a
warranty claim. Proof of purchase is required.
www.myhypergear.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>