HYPERGEAR Sonic Boom 2-In-1 Detachable Soundbar User Manual
- June 5, 2024
- HyperGear
Table of Contents
HYPERGEAR
Sonic Boom
2-in-1 Detachable Soundbar
User Manual
SPECIFICATIONS
1. Power Button / Source
2. Play / Pause
3. Volume Up
4. Volume Down
5. USB Port
6. Micro SD Card Slot
7. Aux IN
8. Optical IN
9. DC IN
10. Coaxial In
LED Display
Status Indicator
Standby mode
Optical mode
Coaxial mode
USB mode
SD Card mode
FM mode
Aux Mode
Bluetooth Mode
Adjust volume The audio play time will be displayed
after
Mute
Pause Blinking
Reading USB / SD Card
Remote Control
- Power On / Off
- Mute
- Volume Up
- Volume Down
- Previous Track
- Next Track
- Play / Pause
- Play via Bluetooth
- Play via Aux
- Change Mode
- Play via Micro SD Card
- Play via USB
INSTRUCTIONS
How to Power the Soundbar
Use the included wall adapter and plug into an outlet.
Remote Control
Requires 2 AAA Batteries
Control remoto
- Remove the battery compartment cover.
- Insert 2 AAA batteries according to the markings inside the compartment.
- Close the compartment.
Connect to Bluetooth Devices
- Press the Bluetooth (BT) button on your remote control, or press the mode button on the soundbar until you hear “Bluetooth” and the display shows “bt”.
- Activate the Bluetooth feature on your device (phone, tablet, etc.) and select “HYG SoundBoom” to connect and pair.
NOTE: If your device prompts for a PIN code, enter “0000”
NOTE: In Bluetooth mode, the connection will be lost if the distance between the Soundbar and the Bluetooth device exceeds 32.8 ft/10m.
NOTE: The Soundbar automatically turns off after 20 minutes in the ready state
Note: If a mobile phone you are playing music on receives a call, the music will stop playing. When the call is ended, the devices are connected to each other again and playback will resume.
Using the Optical Input
- Connect the Digital Optical Audio Cable to the Optical input on the soundbar.
- Connect the other end of the Optical cable to the optical output Audio cable to TV.
- Set the soundbar to Optical mode by clicking the power/ source button on the soundbar or clicking the Mode button on the remote.
- Using the native controls on your connected device, make sure the audio settings are set to PCM or Optical Audio and are turned On. See your TV manual for more info.
- Audio from the connected audio source will now be played through the speakers.
Using the Coaxial Input
Using a coaxial cable, connect the Coaxial connector on your Soundbar to the Coaxial/Digital Out connector on the TV or other device.
NOTE: The digital coaxial connector might be labeled Digital Audio Out.
Using the AUX Input
- Plug one end of a 3.5 mm audio cable into the AUX In on the soundbar.
- Plug the other end of the 3.5 mm audio cable into the Line out/headphone output on an audio device(TV, phone, tablet, computer, mp3 player, etc.).
- Set the soundbar to AUX mode by clicking the power button on the soundbar or clicking the Mode button on the remote.
- Audio played through the connected audio device will now be played through the speakers.
Playing from USB Devices
Insert a USB drive into the USB Port. The soundbar will start playing the music from the USB.
NOTE: The soundbar is compatible with USB drives up to 128GB and can play MP3, WAV and WMA files.
Playing from Micro SD Cards
Insert an SD card into the SD card slot. The soundbar will start playing the music from the card.
NOTE: The soundbar is compatible with SD cards up to 128GB and can play MP3, WAV and WMA files.
Using FM Radio
- Set the soundbar to FM mode by clicking the power button on the soundbar or clicking the Mode button on the remote.
- Under FM mode, press Play / Pause to auto search stations. After searching, it will save the station as a preset.
- Press the Next Track / Previous Track buttons on the remote to select a station.
INSTALLATION
For Soundbar Use
- Connect the two speakers by using the interlocking brackets at the ends of each.
- Twist to align and and secure the speakers.
- Use the short audio cable to ensure audio playback from both speakers.
For Dual Speaker Use
- Attach the standing bases to the ends of each speaker’s interlocking bracket.
- Use the long audio cable to connect to ensure audio playback from both speakers.
Wall Mounting
- Mark the position of the mounting screws on the wall using a pencil
- Drill holes using an electric drill.
- Insert wall studs into the holes using a hammer.
- Secure the screws into the wall stud and leave about 0.3in length to hook the soundbar.
- Put the soundbar onto the mounting screws. Make sure they are firm and stable.
NOTE: The soundbar can also be placed on a stand or table without mounting.
Need help? Visit www.myhypergear.com for additional product information or email info@myhypergean.com
IMPORTANT
Read all safety instructions and warnings prior to using this product. Improper use and failure to follow safety guidelines could result in hazards, injury and/or property damage that is not the manufacturer’s responsibility. The user is responsible for maintaining this product with care for maximum use.
- Do not use near water.
- Clean only with a dry cloth.
- Do not attempt to modify, disassemble, or repair this product.
- Avoid excessive drops, bumps, and abrasions. If the device has dents, punctures, tears, deformities, or corrosion, discontinue use and contact the manufacturer or dispose of in an appropriate method.
- If you find this product rapidly increasing in temperature, emitting odor, deformed, abraded, or demonstrating an abnormal phenomenon, discontinue use immediately.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
- Protect the power cord from being stepped on or pinched particularly at plugs, convenience receptacles, and the point where they exit the appliance or outlet.
- Unplug this apparatus during lightning storms or when unused for long periods.
- Do not use the product for any purpose other than its intended use
- Disposal of the unit in the garbage is unlawful under state and federal environmental laws and regulations.
FCC COMPLIANCE
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
Contact info@myhypergear.com to submit a warranty claim. Proof of purchase is required.
Documents / Resources
|
HYPERGEAR Sonic Boom 2-In-1 Detachable
Soundbar
[pdf] User Manual
Sonic Boom, 2-In-1 Detachable Soundbar, Sonic Boom 2-In-1 Detachable Soundbar,
Detachable Soundbar, Soundbar
---|---