HYPERGEAR 15584 Battle Charge Wireless Charging Gaming Mouse Pad User Manual
- June 6, 2024
- HyperGear
Table of Contents
RGB
BATTLE CHARGE
WIRELESS CHARGING GAMING MOUSE PAD
Mode1:15584
User Manual
NO Metal
NO Magnets
NO Thick Case
Phone cases that contain metal, magnets, or are thicker than 3mm will interfere with wireless charging.
NOTE: This charger is designed for Qi-compatible devices. If your phone does not have built-in Qi wireless charging capabilities, please use a certified Qi wireless charging case or receiver. Refer to your phone’s user manual for detailed features and functions.
SPECIFICATIONS
- 15W Wireless Charging Surface
- USB-C Input Port
- 5ft/1.5m USB-C Cable
- RGB Lights Touch Control
- LED Charging Indicator (on the touch sensor)
| Standby (Ready to Charge
---|---
(breathing)| Charging
| Fully Charged
(flashing) | Foreign Object Detected
NOTE: If the LED is flashing, remove any foreign objects that may affect charging (such as metal plates and other objects) from the charging area.
- RGB Lights (around the pad)
INSTRUCTIONS
How to set up
Use the included Micro USB cable and plug it into either your PC or a wall
adapter (sold separately) to power the gaming pad.
NOTE: This charger is designed for Qi-compatible devices. If your phone
does not have built-in Qi wireless charging capabilities, please use a
certified Qi wireless charging case or receiver. Refer to your phone’s user
manual for detailed features and functions.
CHARGING YOUR DEVICES
Phones
Place your phone on the charging surface. It will indicate when charging
begins.
Wireless Earbuds
Place your phone on the charging surface. It will indicate when charging
begins.
RGB Light Settings
The RGB light settings are controlled by pressing the touch sensor.
Solid Colors
The first 7 light options will be solid colors, touch the sensor to cycle through the options.
Breathing / Flashing Colors
After the solid colors, touch the sensor to cycle through the 3 breathing or flashing options.
NOTE: The lights will automatically turn on when plugged into a power source.
After the solid colors, touch the sensor to cycle through the 3 breathing or flashing options
Turning Off The RGB Lights
For your convenience, you can turn off the lights by pressing the touch sensor for 3 seconds.
IMPORTANT
Read all safety instructions and warnings prior to using this product.
Improper use and failure to follow safety guidelines could result in hazards,
injury, and/or property damage that is not the manufacturer’s responsibility.
The user is responsible for maintaining this product with care for maximum
use.
- Do not place metal objects, magnets, magnetic stripe cards, and hard-drive-based devices near the wireless charger. It may cause data corruption.
- Do not attempt to modify, disassemble, or repair this product.
- Do not expose to water, moisture, or extreme temperatures (below 40°F or above 90°F).
- Under any circumstances, if you find this product rapidly increasing in temperature, emitting an odor, or demonstrating an abnormal phenomenon, discontinue use immediately.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The antennas used
for this transmitter must be installed to provide a separation distance of at
least 20cm from all persons and must not be located or operating in
conjunction with any other antenna or transmitter.
It’s normal for a wireless charger and your device to become warm while charging.
Need help? Visit www.myhypergear.com for additional product information or contact info@myhypergear.com
Contactinfo@myhypergear.com to submit a warranty claim. Proof of purchase is required.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>