PROLED L8000000 LED Panel RGBW L800x000 Instruction Manual

PROLED L8000000 LED Panel RGBW L800x000 Instruction Manual

Characteristics

• SMD CHIP RGBW
• Power consumption 24 VDC, 73 W
• Metall housing square white
• Panel PMMA white Opal
• Beam angle 120°
• Controllable with a Dimmer CA
• Operating temperature range -10° C till +45° C
• CE compliant with applicable European directives
• This product contains a light source of energy efficiency class G

Warning

1. For indoor use only
2. Please ensure that the packaging is disposed of in a safe environment
3. If cable is defected, do not use the luminaire
4. We do recommend that a qualified electrician should be used to install the products
5. Do not look at the lighted lamp directly

Safety indices

Be sure to have a qualified electrician complete installation. The customer is not entitled to claim for any lights installed without observing European safety directives. The manufacturer is then discharged from liability when damage is caused by improper use or installation. If any luminaire is subsequently modified, the person responsible for the modification shall be considered as manufacturer. Do not cover lamp with heatinsulating materials. For indoor use only. Protection class IP40.

Installation

Please follow the sequence of installation step by step. Non-observance can lead to damage of LED.

1. Switch off the electricity at the mains before commencing installation or lamp change and (if a fuse box is installed) remove the appropriate circuit fuse to avoid accidental switching on of the mains supply.
2. Connect the luminaire to a dimmer)
3. Connect the dimmer to a corresponding 24 VDC power supply
4. Make sure all connections are tight with no loose strands
5. Ensure fire regulations are not breached when fitting your lights
6. If you are in any doubt regarding these instructions, consult a qualified electrician

Please follow the sequence, if not destroying of LED:

First

Second

Installation and commissioning may only be performed by qualified persons.
National installation regulations must be observed.
Luminiares must be disconnected from mains before any work.

Mounting possibilities

Recessed mounting

First check if the recessed ceiling meets the requirements:
Panel size Channel dimension Weight
595 x 595 mm 580 x 580 mm ±1 mm ca. 4 kg
622 x 622 mm 605 x 605 mm ±1 mm ca. 4,2 kg
Take out a ceiling panel

Insert the panel under a tilt of around 30-45°

Check that panel rests everywhere with entire surface. Side distance can’t be more than 3mm, otherwise the luminaire may fall down.

Fixing with spring mounting clips

Make a cutout in the suspended ceiling according to below dimensions:
Panel size Needed cutout Weight
595 x 595 mm 575 x 575 mm ±3 mm ca. 4 kg
622 x 622 mm 600 x 600 mm ±3 mm ca. 4,2 kg
The ceiling must have a thickness of min. 1-2 cm, else the luminaire may fall down.
Insert one side with spring mounting clip into ceiling

Lift up the opposite spring mounting clips and insert the luminaire.

ATTENTION: Driver can’t lay on the luminaire
Adjust the lamp so that it covers the ceiling cut.

Rope suspension

Drill holes Ø6mm, 35mm deep. Distance according to slots

Ceiling thickness must be min. 50 mm, else the luminaire might fall down
Insert the dowel and make sure it is installed flush

Put the rope end into flange and make sure, that a rope end secure exists.

Fix the flange at the ceiling

Attach the hangers to the luminaire. The safety lock must be closed, otherwise the luminaire might fall down.

Insert the ropes into the fixings.

Align the luminaire in the desired height and horizontally.

Distance between rope fixings
Panel size
595 x 595
622 x 622
Rope distance
535 mm
550 mm

Frame mounted on ceiling

Build the frame according to the right presentation, so that a three-sided frame is created.

Mark mounting holes on the ceiling, according to the holes in the frame.

Attach the threesided frame to the ceiling with dowel and screws.
Connect the driver and slide the panel with the driver into the frame.

Attach the 4th side of the frame with angles and rest of the screws.

The luminaire can be used now.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>