PAX SK700 Smart Kiosk Instruction Manual
- June 6, 2024
- Pax
Table of Contents
SK700 Smart Kiosk
SK700 Smart Kiosk
Note: Product images shown may be different than actual product received
PAX TECHNOLOGY LIMITED
1ContentsChecklist
Please check the components after unpacking. If any are missing, please contact the dealer.
Name
Qty
SK700 Smart Kiosk
1
SK700 Wall Bracket
1
Printer Key
2
Thermal Paper Roll
1
M4-10 Combination Screw
2
Expansion Screw
6
Plastic Packaging
1
Power Cable
1
Quick Setup Guide
1
2Product Description
Side View
Front View
Interface Diagram
3.Operating Instruction
· Power on: Plug in the AC power cable, press and hold the Power button for
threesecondsuntil the boot animation appears. Power off: Press and hold the
Power button for threeseconds until the
shutdown menu displays. Select Power off. Theterminal turns off after a few
seconds.
4. Payment Options
Magnetic stripe card
Insert magnetic stripe card into card slot and push to the end with magnetic
stripe facing down, then pull out the card at a constant speed to swipe card.
IC chip card
Insert card with IC chip facing up, then push it to theend of the card slot.
Leave card inserted until prompted to remove.
Contactless card
Place the contactless card over the center of contactless card reader logo
area.
Scan
When the scan indicator is on, hold your QR code & bar code device in front of
the scan window to scan code.
5Load Printer Paper
1. Insert the key into the keyhole and turn it counterclockwise to open
printer cover.
2. Completely open the printer cover. 3. Insert the new paper roll into the printer.
4. Pull out the end of the paper so that itextends past the cutting blade,
Make surethe paper roll is placed in the direction asshown in the figure
below.
5.Close the printer cover, and pull outthe key. Printer will automatically cut
offthe extra paper, the paper is changed successfully.
6Wall-mounted Installation
Parts List
No.
Part
Picture
SK700Kiosk
1
Qty/pcs 1
2
Wall Bracket
1
M6-50
3 Expansion Screw
6
4
M4-10
2
Combination Screw
Installation Steps
1. Use 6pcs expansion screws to fix the bracket on the wall. · Use an 8.0 mm
diameter drill bit to drill holes in the wall according to the position of the
bracket fixing hole. The size is shown in the figurebelow: · Note:
Holediameter is 8.0mm, Hole depth is above 60.0mm.
2.Use the 4pcs hooks on the back of the device to hang the whole device on the wall bracket.
3. Use 2pcs M4-12 combination 3screws to attach the machine to the wall
bracket at the bottom of the machine.
4. The device installation is completed.
7.Usage Tips
- There is no built-in battery, and the device can only be powered by the power adapter. 2) Avoid exposing the device in overheated, humid, dusty, or strong electromagnetic environment. 3) Do not vibrate, shake, or drop the device. 4) Do not insert or unplug any part of the device while it is powered on. Otherwise, it may cause damage to the internal circuit. 5) If necessary, please contact PAX technical support for assistance with the device. 6) Before using the magnetic stripe /IC/contactless card, check if there is any suspicious
person nearby, if so, pay attention to guard against theft.
FCC compliance statement This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: — Reorient or relocate the receiving antenna. —
Increase the separation between the equipment and receiver. — Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. — Consult the dealer or an experienced radio/TV
technician for help.
ISED compliance statement This device contains licence-exempt
transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions: (1) This device may not cause interference. (2) This
device must accept any interference, including interference that may cause
undesired operation of the device. L’émetteur/récepteur exempt de
licencecontenu dans le présentappareilestconforme aux CNR d’Innovation,
Sciences et Développementéconomique Canada applicables aux appareils radio
exempts de licence. L’exploitationestautorisée aux deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage; (2) L’appareildoit accepter
tout brouillage radioélectriquesubi, même si le brouillageest susceptible
d’encompromettre le fonctionnement.
ISED 5G Wi-Fistatement The user manual for LE-LAN devices shall contain
instructions related to the restrictions mentioned in the above sections,
namely that: i. the device for operation in the band 51505250 MHz is only for
indoor use to reduce the potential for harmful interference to co-channel
mobile satellite systems;
ii. where applicable, antenna type(s), antenna models(s), and worst-case tilt
angle(s) necessary to remain compliant with the e.i.r.p. elevation mask
requirement set forth in section 6.2.2.3 shall be clearly indicated.
i. le dispositifutilisé dans la bande 5150-5250 MHz estréservé à
uneutilisationenintérieurafin de réduire le risque de brouillagepréjudiciable
aux systèmes mobiles par satellite dans le même canal; ii. le caséchéant, le
(s) type (s) d’antenne, le (s) modèle (s) d’antenne et l’angle (s)
d’inclinaison le plus défavorablenécessaire (s) pour resterconforme (e) au
p.e.L’exigence relative au masque d’élévationénoncée à la section 6.2.2.3
doitêtreclairementindiquée. Radiation Exposure statement This equipment
complies with FCC/IC RSS-102 radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator and your body. Cet équipement est
conforme aux limites d’exposition aux radiations FCC/IC CNR-102 établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé
avec une distance minimale de 20 cm entre le radiateur et votre corps.
PAX TECHNOLOGY LIMITED reserves the right to change product
technology specifications without notifying.
PAX TECHNOLOGY LIMITED
Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd. Address:4/F, No.3
Building, Software Park, Second Central Science-Tech Road, High-Tech
Industrial Park, Shenzhen, Guangdong, P.R.C. Tel: 0755-86169630 Fax:
0755-86169634 Website: http://www.pax.com.cn Responsible Party:PAX Technology,
Inc. 8880 Freedom Crossing Trail, Building 400, 3rd Floor Suite 300,
Jacksonville , Florida, 32256 Help-desk 1
877-859-0099
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>