BASS JAXX HP-0414 BT Wireless Headphone Instruction Manual
- June 6, 2024
- BASS JAXX
Table of Contents
SENSOR
WIRELESS HEADPHONES
INSTRUCTION MANUAL
Introduction
Congratulations, and thank you for choo5 the Sensor Wireless Headphones.
This manual will help you operate the Sensor Wireless Headphones, but firstly
you should familiarize yourself with the Bluetooth functionality of your
mobile phone or other devices before using the Sensor Wireless Headphones.
Safety Rules
-
Please follow the rules depicted in this manual closely to ensure your safety.
Before using these Bluetooth headphones, we would strongly encourage you to read through this user manual. -
Be warier of any edges, uneven surfaces, metal parts, accessories, and packaging so as to prevent any possible injury or damage.
-
Do not modify, repair or dismantle these Bluetooth headphones.
Doing so may result in fires, electric shocks, complete breakdown of these Bluetooth headphones, etc. All are not covered under warranty. -
Do not use a diluent or volatile liquid to clean the Bluetooth headphones.
-
Do not use Bluetooth headphones in a hazardous location.
Packaging Contents
Connection Diagram
How to use
General Functions
Desired Result|
Required Action
---|---
Turn on & Enter the pairing mode| Press and hold the On / Off Button for 3
seconds. After turning on, the LED indicator flashes red/blue.
Pairing| Use a mobile phone with Bluetooth function or other Bluetooth devices
to perform necessary pairing action.
After pairing, the LED indicator slowly blinks with blue.
Turn off| Press and hold the On / Off Button for 3 seconds.
Charging| Method 1: Plug the Micro USB into the micro USB port.
Method 2: Put Headphone’s earcup to the wireless charging pad.
When charging, the LED indicator turns red after full charge, the LED
indicator turns off on both methods.
Answering a Call| Press the On / Off button to answer the phone call press the
On / Off button again to end the call. Press and hold for 2 seconds to reject
the call. Double dick to redial the last call.
Play / Pause Music| Press the On / Off button to play music and press it again
to pause music.
4.2. Pairing to a Mobile phone or another device
To use your Bluetooth headphones, you must first pair your headphones with a
mobile phone or another Bluetooth device. Once your Bluetooth headphones are
paired to a specific mobile phone, they will remain paired and automatically
recognize each other whenever they are within range.
Pairing to a phone and Entertainment:
- Turn on your phone and ensure the Bluetooth function is activated.
- Turn on the headphones, enter the pairing mode.
- Search your Bluetooth devices on your phone by following the phone’s instructions. Refer to your phone’s user manual for more information.
- After a few seconds, the phone will list the “BT SENSOR HP” as a discovered device. Select it and follow your phone’s instructions to select this pairing.
- Your phone will confirm the pairing and then press Yes/OK.
4.3. Charging your Headphones
Method 1
For your safety, please always use an appropriate 5V input charger/Adapter to charge the product. DO NOT USE Quick Charging USB Adapter to charge the product, as it might damage the product.
Use the Micro USB charging cable accessory provided with these headphones.
Connect the Micro USB plug to the Micro USB charging port on the headphones
positioned at0 in the headphones diagram on page 2. Connect the USB plug to a
USB port on a computer or wall adapter to activate charging.
**Make sure to keep the headphones charging for a minimum of 2 hours before
initial use.
Warning:
- You must select a qualified charger from a regular manufacturer.
- You must charge the Bluetooth headphones if it has not been used for more than 6 months.
Method 2
You can also charge your headphones by wireless charging pad as below way.
Product Specification
Driver Diameter: 40 mm
Impedance: 32 Ohms
Frequency Response: 20 Hz – 20K Hz
Sensitivity: 100 dB +/- 3 dB
Battery Capacity: Li-ion Battery 3.7 V 180 mAh
Playtime: 2-3 Hours
Charging Time: 1.5-2
Hours Bluetooth Range: 32.8
Feet Bluetooth Version: 5.1
Charging Method: Wireless Charging / Micro USB Charging
FAQ
- Why is there no power even when the headphones are turned on? Ans: Ensure the battery has been charged for up to 1 hour for initial use.
- There is no sound when playback. Ans: Check the connection between headphones with phone or computer, if the connection is not established, please connect again. Make sure the headphones are paired and connected with your target phone or another master device.
FCC Statement
FCC STATEMENT
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Safety instructions for the lithium battery and charging the product
-The input voltage to the product is 5V 1A.
-In order to charge the product in a safe manner and reliable conditions, please only adopt a certified appropriate charger/ adapter for charging the product.
-Only charge the product at ambient temperatures between 10 deg °C/ 50 deg °F and 40 deg °C1104 deg °F.
– Do not heat above 70 deg °C/158 deg °F, e.g. Do not expose to sunlight or
throw into fire.
-Switch off the product after use.
-Please note that we won’t take any responsibility for any wrong operation (e.g. Voltage higher than 5V) as this may result in severe injury or loss of property, and we cannot control the operating process during the time the user using this product.
-In extreme cases, abuse or misuse of the Lithium battery packs can lead to an explosion, heat generation, fire development, or smoke development.
FCC ID: 2ADM5-HP-0414
Distributed by 1616 Holdings, Inc. 701 Market Street Suite 200 Philadelphia,
PA 19106
Item # HP-0414
Made in China
Keep All Relevant Information For Future Reference