BASS JAXX EP-0654 Solo Wireless Earbuds Instruction Manual
- June 6, 2024
- BASS JAXX
Table of Contents
INSTRUCTION MANUAL
Thank you for purchasing the Solo Wireless Earbud. This manual provides more
information about the wireless earbud, please read the instructions before
using it.
Solo Wireless Earbud
Portable Charging Case
1. On/Off Button/ Play/Pause Music Answer/End Call
2. LED Indicator
3. Charging On/Off Button
4. Micro USB Charging Port
|
Micro USB Charging
---|---
Package Contents
Solo Wireless Earbud x
1 Portable Charging Case x 1
Micro USB Charging Cable x 1
Instruction Manual x 1
Specifications
Driver Diameter: 10 mm
Impedance: 32 Ohms
Frequency Response: 20 Hz – 20 KHz
Sensitivity 96 dB +/- 3 dB
Power Supply Li-ion
Battery 3.7V 35 mAh
Playtime: 6 Hours
Charging Time: 3 Hours
Bluetooth Range: 32.8 Feet
Charging Case Battery Capacity: 200 mAh Micro USB Charging Cable Included
Power On/Off
Power On
Press and hold down the On/Off Button of the earbud for 3 seconds and the LED
will flash.
Power Off
Press and hold down the On/Off Button of the earbud for 4 seconds and the LED
will turn off
Pair the wireless earbud with your mobile device
- Keep the distance between the earbud and mobile device within 32.8 feet.
- Deactivate the Bluetooth function on your mobile device.
- Power on the earbud simultaneously by pressing the On/Off buttons for 3 seconds and waft for 3 to 5 seconds for auto-pairing. The earbud has an indicator blinking alternatively in Red and Blue. The earbud will be blinking in Blue slowly when auto-pairing is done successfully on the earbud.
- Activate the Bluetooth function on your mobile device and select “BT SOLO EARBUD’ from the list shown.
- After pairing is successful, the earbud will start blinking slowly in blue.
Reconnect the wireless earbuds to your mobile device
When powered on, the wireless earbud will automatically connect with the last
successfully paired device.
Disconnect the wireless earbuds from your mobile device
Power off the wireless earbud; or Switch off the Bluetooth on your mobile
phone: or Leave the earbud 60ft away from your mobile phone or further.
Answer / Reject a call
When receiving a call, press the On/Off Button once ( on either earbud) to
accept the call, or answer the call normally via your mobile phone. Press and
hold 2 seconds to reject it.
End a call
To end the call, just press the On/Off button on the earbud with the Beep
sound to end it
Charging your Earbud with a Charging case
- Open the charging case cover.
- Put earbud to the charging case and press the charging On/Off button to start charging.
- The earbud LED indicator light turns red when charging your earbud. 4. Earbud LED indicator light turns off when your earbud is fully charged.
Recharge Charging Case
For your safety. please always use the appropriate 5V input charger/Adapter to
charge the product DO NOT USE Quick Charging USB Adapter to charge the
product. as it might damage the product
- Use the Micro USB charging cable provided with the packaging.
- Connect the Micro USB plug to the Micro USB charging port on the charging case, then connect the USB plug to a USB port on a computer or wall adapter to begin charging.
- The Red LED on the charging case will be flashing during charge.
- Once fully charged, the Red LED will be on and stop flashing.
NOTE:
- You must select a qualified charger from a regular manufacturer.
- You must charge the charging case and earbuds if it has been not used for more than 12 months.
FAQ
If the wireless earbud cannot be paired with your device, please try the
following:
Ensure that your earbud is in pairing mode or reconnection mode
Ensure that the Bluetooth search function of your mobile device is activated.
If the wireless earbud will not turn on:
Make sure the earbud is fully charged.
Can I change the battery for the charging case and earbud?
The charging case and earbud use a built-in non-detachable battery which
cannot be removed.
If the charging case cannot be recharged:
If you use a power outlet. ensure that the power supply is connected securely
and the outlet works. If you use a computer, ensure that it is connected and
the USB port is powered.
Safety instructions for the lithium battery and charging the product
-The input voltage to the product is 5V 1A.
-In order to charge the product in a safe manner and reliable conditions, please only adopt a certified appropriate charger/ adapter for charging the product.
-Only charge the product at ambient temperatures between 10 deg °CI 50 deg °F and 40 deg °C/104 deg °F.
– Do not heat above 70 deg °C/158 deg °F. eg. Do not expose to sunlight or
throw into fire.
-Switch off the product after use.
-Please note that we won’t take any responsibility for any wrong operation (eg. Voltage higher than 5V) as this may result in severe injury or loss of property. and we cannot control the operating process during the time the user using this product.
-In extreme cases. abuse or misuse of the Lithium battery packs can lead to an explosion, heat generation, fire development, or smoke development.
FCC STATEMENT
1. This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) This device may not cause hamiful
interference. (2) This device must accept any interference received, including
interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Conned the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
RF warning statement:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
FCC ID: 2ADM5-EP-0654
Keep all relevant Information for future reference
ITEM# EP-06 54
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>