SANSI C21FG001 RGB Smart LED Floodlight User Guide
- June 6, 2024
- SANSI
Table of Contents
SANSI C21FG001 RGB Smart LED Floodlight
Product Overview
- Lampshade
- Lamp base
- Hex bolt
- Mounting bracket
- Power cord with plug
You will need
Technical Data
Assembly/ Installation
Unpack the product and check the delivered components are complete and without
any damage, read the user manual carefully.
Steps: Install the product onto the reserved surface for the
installation->Tighten the product with M6 suites afterward.
Note:
- Tighten the bolts, nuts and all fastening sets. Do not screw these fastening sets too tightly.
- Ensure the voltage given on the rating label / In the Instruction manual complles with the power supply.
Angle Adjustment
- Loosen the fixing bolts on both sides with suitable Hex key by turning them counterclockwise. Only loosen the fixing bolts until the mounting bracket can be adjusted.
- Adjust the mounting bracket to the desired angle, then re-tighten the fixing bolts by turning them clockwise
Install the App
- Search Stellar BLE on App Store(iOS) or Playstore(Android) to get the App.
- Download the App and Install it.
NOTE: If the App is already on the smartphone, make sure it has been updated to the latest version.
Add Device
- Prepare the SANSI smart light and connect the power caret
- Install the Stellar BLE, open the App.
- Make sure the Bluetooth on your phone is on, get the phone close to the device.
- Tap”+” on the top right of the “Light” interface, tap “Add Devices” to start searching devices.
- After the device is displayed on the list, select the device to be added, tap “NEXT” to continue.
- Wait for the device connection, ensure it has been added successfully, tap “OK” to finish.
Note: Retry It several times If adding failed due to connection error.
Factory Reset
2 methods are available to reset the device to factory default.
- You can select “Dlsconnect”on the Light Information interface, then select Remove, the device will be reset successfully after it blinks to constant white light.
- You can also complete the reset by quickly switching On and Off for 6 times, the device will be reset
Other Functions
- Dimming
- RGB color change
- Schedule On/Off
- Countdown
- Group Management
Safety warnings
- Read the instruction manual thoroughly before first use. Follow all the safety instructions and information.
- If installed outdoors, the plug must be connected to an indoor socket or a socket that offers the same IP protection as the luminaire.
- Do not place any objects on the product. Mechanical loads may damage the product.
- Do not cover the product/ lampshade e. g. with paper or textiles.
- Risk of burns! Do not touch the light source or the housing during use.
- Ensure the voltage given on the rating label or in the instruction manual complies with the power supply.
- Do not use the product if the parts are damaged, the product does not work properly or if the product is damaged.
- Do not open the housing under any circumstances. Do not insert any objects or fingers into the housing interior.
- Do not stare at the operating light source or direct the beam at other people or animals to prevent eye damage.
- Install the product according to the intended use and as described in this manual.
- Do not assemble the product in adverse ambient conditions or in rooms where heat sources, hot steam, corrosive gas, flammable gas, vapors or dust are present.
- Do not assemble/ install the product under live conditions.
- There are no parts inside the product that can be repaired by the user.
- If the external flexible cable or cord is damaged, it shall be exclusively replaced by the manufacturer or its service center or a qualified specialist in order to avoid a hazard.
- The light source and power supply driver of this product are not replaceable. When the light source or power supply driver reaches the end of their life, the whole luminaire should be replaced.
Warranty & Contact
5-year warranty
Email: service@sansiled.com
Web: www.sansiled.com
Mfg. date is printed on the Gertificate of Approval.
FCC Statmrnt
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirements. The
device can be u sed in portable exposure condition without restriction
FCC ID: 2A4AE-C21FG001
Documents / Resources
|
SANSI C21FG001 RGB Smart LED
Floodlight
[pdf] User Guide
C21FG001, 2A4AE-C21FG001, 2A4AEC21FG001, C21FG001 RGB Smart LED Floodlight,
RGB Smart LED Floodlight, LED Floodlight, Floodlight
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>