SANSI C2440 27W LED Security Light User Manual

C2440 27W LED Security Light

SRN•1J
SRNQ _
1. This product is suilable for use in wet locations.
2. Do not hang any objects on the product. Mechanical loads may damage the
product.
3. Risk of burns! Do not tooch the light sooroe or the housing during use.
4. Ensure the voltage given on the rating label or in the instruction manual complies
with the power supply.
5. Do not use the product if the parts are damaged. the product does not work properly
or If the product Is damaged.
6. Do not stare at U1e operating light source or direct l he beam al other people o r
animals, to prevent eye damage.
7. Assemble I Install the product accordlng to the Intended use and as described In this
manual.
8. Do not assemble/ install the product in adverse ambient condilions or in rooms,
where heat souroes, hot steam, oorrosive gas, flammable gas, vapors or dust a re
present.
9. The operating ambient temperature of tho product is -25 – +40’C; store the product
and its accessories und&r-20 – +65’C. Do not use the product under the conditions
with extremely high or low temperature.
10. Ensure the mounting surfaoe (e. g. wall surface etc.) can load the weight of the
product.
11. Do not assemble I install the producl under live conditions.
12. To avoid pefSCnal hazard and product damage. Keep the children or pets away
from the product and Its accessories during assembly I Installation .
13.There are no parts inside the producl lhat can be repaired by the user.
14. Do not install the prooucl in the electric circuit loop with a d im,ner.
15. If the exterMI flexible cable o r oord is damaged, it shall be exclusively replaced by
the manufacturer, the service center or a qualHled speclallsts to avoid hazards.
16. The ligt,t source and tho power supply driver of this produ~1 aro notrcplaccablc.
ll’n-ien the light source or power supply driver reaches its end of life , the whole
luminaire shall be replaced.
Energy efficiency class
C2440-MW-15W This producl conl:ilns light source,; of energy effidency class : D
C2440-MW-30W This product contains ligt’II source,, of energy efficiel’ICy class : D
C2440-MW-45W This product conlalns light sources of energy efficiency class: D
SRNQ ____ affilll
Before installation. please read all of the inslruclions thoroughly and keep it for future
reference .
Product and accessories
All parts and aooes.-;ones are to be found in the packaging. If some of them are
missing, please contact us via serviceGsansiled.eu.
LEO wt’1ri.y l,v1tl
/
Tools needed
3
Bat-e.1′:!PtO mo.r11nQ owe
wilh 2 fi11.:uy bu!lti w,d 1
e..mini,;i C011K1ior bolt
lmpw;tdrill
SRN5I ____ .affilll
Flxlngbotl
t.irthing connection bolt
Step 2: Installing the live and neutral wires
Bnown – live wl re (L) Blue – neutral wire (N)
Strip the wires 9.5 mm, if necessary. Hold the live wire and the brown lixture wire
together with even ends. Twist the wire ends and push them into the wiring nut.
Clamp down the wiring nut with suitable pliers afterwards. Repeal the same
procedure lor the neutral wire and ~10 blue fixture wire.
Con~ tt\e t•lt.• ~tfa.l _,.e
with Iha bt JO lbchira wire
CCl11n&=t the b’O”M”I IN& wire w«h
Lr,;, un.,v.i J,.._l~ wife
.- ~’, ‘:,.-
c:~~
Step 3: Mounting the product
Brown – L””8 wire 1;t.!
l”I IW!· Nl!,1!1″111 vlirl’! (N)
1. Insert the mounting bolt 1hrough 1he center of the housing and rear cover.
2. Align the mounting bolt through the center ol lhe sealing gasket lo hold tt in place.
3. Align the mounting bolt wrth the center hole or the bar-shaped mounting plate.
4. Position the housing and sealing gasket over the junction box.
5
SRN5′ __ affilll
Strip the wires 9.5 mm. if necessary. Hold the live wire and llhe brown fixture wire
together with even ends. lwist the wire ends and push them into the wiring nut.
Clamp down the v,iring nut with suitable pliers atterwards. Repeat the same
procedure for the neutral wire and the blue fixture wire.
Ci,rn10C lt1t1blt.~ r >:1Uln:.I
wire v,ith tht,, blue 1ixlur9′ wire
1J
Ct:111,tr.:I U14o b’U”‘fl i,,,i, wirv
v.tu, :he bra.Tl lb,:o.we •.-.Ire
Step 3: Mounting the product
ero-…r – LIiie wife 11.j
Bw- N1;1.11t.1l ,.li1u (N)
1. Insert the self-tapping screw through the centllr of th<> housing and the rear cover.
2. Align 1he sel f-tapping screw t11rough the center of the sealing gasket lo hold it in
place.
3. Align the self-tapping screw with the Nylon dowel.
4. Use a screwdriver to screw it into the Nylon dowel, until llhe product is securely
fixed.
7
SRNQ ____ .affilll
@ Mom•® —. sensor .,,.-
4. Move thmugh the test area and note your position, when the p roduct turns on (LED
light source will illuminate continuously for several minutes wh en any motion signal is
captured).
5. Adjust the motion sensor upwards, downwards or sidewards to change the sensing
distance.
6. Toa distance between tha motion s<.ll’lsor and the l:imp h..ads $hall be at least 25 mm.
7
Ad Just tht morion sensor downw.vds
to decrease the sensl.rtg dLStaoce
~u,;1 the mo1IM S(nso, UJ¼\’.”lrds to
lncreue the sensing distance
7. Rotate the Range control knob, it necessary. A sensing range lhat is too large may
result In activation fault.
8. If the motion sensor is loose, tighten the clamping screw. Do not overtighten the
clamping screw.
9. Tum the Time control knob to set the operating time from 1 – 10 minutes according
to your needs.
WARNING: Frooue.-t e.wacNno on/ off tl’o Croclls::t wll ro~ico the r,.ojv~’o lilcooon,
WARNING: K96P 1h& pro:,llct aw~ trcm a,y 1ir$ SOJrC,9S,
WARNING: -he light socrce and the po,>Er su~pty d~ver of t~ ls :r~dc:t are net rep aceat e.
9
t,,V~,:,n thP irJht “<lL’l'”P ..-., no\w:-~ “t1r:;”)ly :iri….,.~ rP;;.-,p,; it<: P11rl nf f?, rt;:. whn!P unir ;iirP
;;’1;;1 be •~•p!acc:1
SRNQ _ ~llll[ffi)I
020 night time constant-on mode
The LED light source lights up automatically at dusk and lights off automaUcally at
dawn when in 020 mode.
Lux – control knob for brightness sensitivity
Tha Lux control knob is designed to set tha brightn8SS value for tha motion sensor.
If lhe ambient brightness is l1i9her lhan your sellings, it is deli110d as “day time• and
the LED light source does not lighl up.
If the ambient brightness is lower than your settings, ii is defined as “night time” and
the LED light source lights up.
NOTE: P.HtXIIIIHHf (kl :-;1-dli ~I i:; htllY’Wl’,’ ot t•~ Lux dfJ. Hil,I Lua ::Hlli11;1 ‘A’ I (Hu:•H U,;,t I E:I) litit tl :•Oll::f<
lghlhg u:> t.l:he d-ne: w’rlllethe tiw Lux settl,g wtll ~se tie LC:+ I gl”: soJrce flashng.
Time – control knob for operating time
The Time control knob Is d eslgned to set the operallng time of the continuous
lighting, once the motion signal is detected.
The minimum setting is 1 minute and the maximum is 1 O minutes..
Range – control knob for sensing range
The Range contml knob is designed to set the sensing range.
Turn the Ronge control knob counterclockwise to decrease the sen.ing range, while
clockwise to increase the sensing range.
NOTE: ‘l,her ~’OU $\•,l e, 0.1 tie pro;::Uot tre LED light SOl..l’OS is lh .. mirated Jo~ app’t;.;, $5 secon::ts It is
Cal lad u•e “•.¥ftkQ•~ pro:.ESS”. Al1″1r lh9 “wal<.&–14″: pnx,ess·, SV11IC1′ the OtOdu-::1 tc ,l)Q :esf9CI wo·kirg
·ncx1a Ar.1t1rt f,::P1 t,e On Tlme~. the I ffili;-1ht sourcew 1•1t1s’l:,t,1:ara ti”nas~rlEr sv,tt<;r1ir1n ~ tweer
each c’ It& wo1<1ng mcd8s.
2-years warranty
If you have any problems, questions or concerns, please feel free to contact us before
re1urning tha product. The email of after-sales SE!rvice is: service@sansilad.eu.
The Mfg. Oate is printed on the Certificate of Approval.
11
I User Manual
Model: C2440-MW-15W I 30W / 45W
Dimensions/ Abmessungen I Dimension /
Dimensioni / Dimensiones
C2440-MW-15W
C2440-MW-30W
~—–373 —–~
C 2440-MW-45W
~——◄89 ——~
2
affill __ SRN5l
Installation
Before Installation
1. TI1e product shall be mounted ,-ertically on a flat surface of the wall.
2. Input voltage: loc-.:il mains supply
3. Mo un I the p.-oduct at a 11eighl of 1 – 4 m. me optimal mounting height is 2.4 m.
~Tptoad
AA~A1tl !Xl~llic,n
nr.i-,li’V’l”q’/t fl’t]Ul”‘.i'”
/ ,/
,: I OOO~ ooo l~J.,,1)
Mol~l 8¥$:11
‘
I
~ ?5~ \.. ..:,.; ‘-..’.–‘ ,’
–
T;’.M rmdr. ( ,..Id ‘ I \ … C,,,,lmr! tlt’li!ttlW!f (:r
-~~– /
,,., .. ” .
C-.nntml hrr.h t.ir’:1m!llr ,,Cor,~,ol kncb for b~rw..u
\ tl’l00e(020j
I I
J,,ul,Omo:ti,;Aulo) -l – Orec-L-oor1.’01mt0e
iy,jh oi,•~ svJitch1 I On n-1
raroecnan.oeJ I str,~(Luic>
r,u,1r::i kMb tot
~J-11’1″111(~1
OPTION 1 – with junction box
Step 1: Fixing the mounting plate and installing 1he
earthing wire
1. The bar-shaped mounl ing plate only matches with the standard junction box with an
installation pitch of 88.9 mm.
2. Make sure the bar-shaped mounting p late is firmly tightened with the 2 fixing bolts.
3. The earthing wire Is not pre-Installed. Flt the loop end of the earthing wire onto the
mounting plate and then secure it wrth t he earthing connection bolt (green- colored
screw head).
4
affill _ SRN5l
5. Use a screwdriver to screw the mounting bolt into the mounting plate. until llhe
product Is securely fixed.
6. Fit U1e rubber screw cap onto the mounting bolt.
OPTION 2 – without junction box
Step 1: Fixing the Nylon dowel
1. Use a proper imp act drill to drill a hole (0 8 x 50 mm) on the wall.
2. Fully Insert the Nylon dowel Into the hole.
Step 2: Installing the live and neutral wires
Brown – live wire (L) Blue – neutral wire (N)
6
affill SRN5I
Settings
1. Switch on the circuit breaker and the product.
NOTE: Fer 1h! flrs1 us.,/ sv,1tchlrg-on, the m011o1 sens of raou -es tc wanr ~ for 1.5 mlM!s. t6for& 11 can
r::ciph.r~ :mv mntinn
2. Se1 the working mode switch to the test mode (Test) and then turn the Range control
knob to the middle position (between the maximum and minimum settings).
NOTE: S-Ot t·,c Ulx c~ttro knoo·o h~lfrv,:;·,:, in oroortonot ~ btiior :,erf:::n1ur..-:o
Bottom vi&.v of thA motion f”..anAor
Cautions
1. Keep the p.-oduct away from any oblects with rapid temperature fluctuations, such
as heating air vents or air conditioners. These heat sources may result in ac1ivat ion
faults.
2. The producl may be activated/ switched on by moving pets or passing vehicles.
3 . Nearby large-sized light-colored objects, which reflect light may also activate th<>
switching-on of the p roduct. Do not direct any type of light towards the motion
sensor.
maximum tensing dlstal1(e maximum sen11n9 range
NOTE: “1:ij1.,s: th::: motion &:f!cor :.1ownw0fd~ to ol”or.m :lie SCflo!ng :t.;to1co. If tic pro:uci lo mounted ot
ai tegi-: (;’,’Fir 2.-1 rr. The nc:lor ~· “\.’JF. 3. k”1Aiar SArif. t ·.ii’)• tn ohjei.t:~ movhg t<W1an::s ~
affill Working mode
Working mode
Test
Auto
On Time
020
Operaling time
5seconds
1 – 10 mi11utes
always on until switched off
from dusk to dawn
Operation: Day I Night
8
NOTE: ‘/vh;:w- l JFJF. / f.W7m :n ~A pmct.JC: k:,.- h;; ·,ct ii,TIA, vr,:..; lo: 1 • 2 mhutff. tr..- the f’:l9::tril’.;tl C’ .«..Jit t::
autcma::lcal)’ ca !bra te.
Functions
Set the wOftk’g mode switch.
Tel51 – test mode
Tho product works for 5 soconds during the day or night when in tc.-st mode.
It was designed to check whether the motion sensor can wOfk prope,ty.
Auto – auto mode
The product only works for 1 – 1 O minutes at nighl when in auto mode. It depends on
the operating time you set.
If you switch off the product for 1 • 2 seconds and then switch rt on, the product will
work constantly for up to 8 hours at nigl11.
To back to the auto-mod e, switch off the product and then switch it on again.
It will also be automatically back lo aulo mode, when ii is bright around (> 150 lux).
On Time – direct-control mode (with the on/off switch)
Both in the day time and night t ime, the LED light source will light up, when the
product is switched on and lights off when the proctucl is switched off.
10

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>