SANSI C21FG002 RGBW Smart LED Flood Light User Guide

SANSI C21FG002 RGBW Smart LED Flood Light

Product Information

The RGBW Smart LED Flood Light is a high-quality lighting solution that allows you to control the light color and brightness using your smartphone. It is equipped with advanced features and can be easily installed for both indoor and outdoor use.

Dimensions

• Length: 4 inches (102mm)
• Width: 5 inches (129mm)
• Height: 1.3 inches (33mm)

Installation

1. Take the product out of the package and read the user manual carefully.
2. Prepare the mounting surface by installing M6 anchor bolts according to the mounting slots on the bracket.
3. Install the product onto the mounting surface and tighten the hex nuts to secure it.

Angle Adjustment

1. Loosen the fixing bolts on both sides by turning them counter-clockwise until the mounting bracket can be adjusted.
2. Adjust the light panel to the desired angle.
3. Re-tighten the fixing bolts by turning them clockwise.

Get the App

To control the RGBW Smart LED Flood Light, you need to install the Stellar BLE App on your smartphone. Follow these steps based on your device:

Android:

1. Open Google Play.
2. Search for “Stellar BLE”.
3. Download and install the App.

iOS:

1. Open App Store.
2. Search for “Stellar BLE”.
3. Tap “Get” to install the App.

Add Device

1. Prepare the smart flood light and connect the power cable.
2. Install the Stellar BLE App and open it.
3. Make sure your phone’s Bluetooth is turned on and keep your phone close to the light.
4. Tap the “+” button at the top right of the Light interface and select “Add Devices” to start searching for the device.
5. When the device is displayed in the list, select the device you want to add and tap “NEXT” to continue.
6. Wait for the device to be connected and added successfully, then tap “OK” to finish.

Factory Reset

To reset the device, you have two methods:

1. Select “Disconnect” on the Light Information interface, then select “Remove”. The reset is successful when the light blinks.
2. Alternatively, quickly switch the device On and Off for 6 times to complete the reset.

Product Parameters

Please refer to the product manual or contact our customer support for detailed information about product parameters.

Warnings

• Ensure that the voltage of the power supply complies with the operating voltage of the product before use.
• The light source of this product is not replaceable. When thelight source reaches its lifecycle, the entire luminaire should be replaced. Do not attempt to disassemble the product.
• Do not look directly into the operating light.
• Do not assemble the product under live conditions.
• The assembly and maintenance should only be performed by a qualified specialist.
• If the power cord is damaged, it must be repaired by themanufacturer or its authorized service center, or replaced by a qualified specialist.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. It should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Please note that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCCID: 2A4AE- C21FG002

Thanks for purchasing our product, to ensure full understanding of the product and know how to use it properly, please read the user guide thoroughly and keep it for potential use.

Dimensions

Installation

1. Take the product out of the package. Read the user manual carefully.
2. Prepare the anchor bolts on the mountingsurface according to the mounting slots on the bracket.
3. Install the product onto the mounting surface and tighten the hex nuts afterwards.

Angle adjustment

1. Loosen the fixing bolts on both sides by turning counter-clockwise. Only loosen the bolts until the mounting bracket could be adjusted.
2. Adjust the light panel to the desired angle, then re-tighten the fixing bolts by turning them clockwise.

Get the App
You can install the Stellar BLE App via below methods:

Android：

1. Open Google Play.
2. Search fo“r Stellar BLE.”
3. Download and install the App.

iOS:

1. Open App Store.
2. Search for“ Stellar BLE”.
3. Tap“ Get”to install the App.

Add device

1. Prepare the smart flood light and connect the power cable.
2. Install the Stellar BLE, open the App.
3. Make sure your phone’s bluetooth is on and keep your phone close to the light.
4. Tap“ +”at the top right of the“ Light”interface and selec“t Add Devices”to start searching for the device.
5. When the device is displayed in the list, select the\ device you want to add and tap“NEXT”to continue.
6. Wait for the device to be connected and added successfully, tap“ OK” to finish .

Factory reset

2 methods to reset the device

1. You can select“ Disconnect”on the Light Information interface, then select Remove, reset successfully after the light blinks.
2. You can also complete the reset by quickly switching On and Off for 6 times.

Product Parameters

• Model : C21FG002-B0100A40
• Enclosure Color : Black
• Material : PC + Aluminum
• Input : AC 120V,60Hz
• Rated Power : 100W
• Color Temperature : RGB+5000K
• Controlled by : Mobile App
• Connection : Bluetooth
• Beam Angle : 110°
• Lifespan : 25,000 hrs
• Dimensions : 451.3″(10212933mm)
• Net Weight : 460g
• Working Temperature : 14-104℉
• Working Humidity : 10%-90% RH
• IP Rating: IP66

Warnings

1. Ensure the voltage of the power supply complies with the operating voltage of the product before use.
2. The light source of this product is not replaceable; when the light source reaches its lifecycle, the whole luminaire shall be replaced. Do not attempt to disassemble the product.
3. Do not look into the operating light.
4. Do not assemple the product under live conditions.
5. The assembly and maintenance can only be performed by a qualified specialist.
6. If the power cord of the outer material is damaged, it must be recorded and repaired by the manufacturer or its authorized serivce center; or replaced by similar qualified specialist.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 ofthe FCC
Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
   FCCID： 2A4AE-C21FG002

Warranty & Contact

• 1-year warranty
• Email: service@sansiled.com
• Web: www.sansiled.com
• Mfg. date is printed on the certificate of approval

References

• Grow Light, Light Bulb, Flood Light and More | LED Lighting Provider

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>