bbpos HB2D Toast Direct Attached Instruction Manual
- June 6, 2024
- bbpos
Table of Contents
bbpos HB2D Toast Direct Attached Instruction Manual
Instruction
Follow your application instruction to start the transaction process, then swipe, insert or tap card to complete the transaction.
If you pay via inserting EMV IC card, please ensure that the EMV chip of the
card is facing the right direction. If you pay using NFC card, please ensure
you tap the NFC payment card within 4cm range on top of the NFC marking.
NFC Status Indictors
-
First LED ON
Ready for tapping card
-
LEDs ON in consecutive order
Reading card information -
4 LEDs ON + “BEEP”
Card reading process successfully completed -
“BEEP”
Transaction completed
-
First LED flashing
Standby mode
-
2 “BEEP”s
Error, please retry
Cautions & Important Notes
- Ensure the device is fully charged before use.
- Please ensure EMV chip of the card is facing the right direction when inserting card.
- The NFC card should be tapped within 4 cm range on top of the reader mark.
- Don’t drop, disassemble, tear, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint or insert foreign object into the device. Doing any of which will damage the device and void the Warranty.
- Don’t immerse the device into water and place near washbasins or any wet locations. Don’t spill food or liquid on the devices. Don’t attempt to dry the device with external heat sources, such as microwave or hair dryer. Don’t use any corrosive solvent or water to clean the device.
- Recommend using dry cloth to clean the surface only.
- Don’t use any sharp tools to point the internal components, connectors or contacts, doing which may lead to device malfunction and void the Warranty simultaneously.
Product Specifications
Functions
|
- EMV chip card reader (ISO 7816 compliant clan A, B, C card)
- NEC Card (loader (FUN contactless. ISO 14443/1/13)
- Over-the-air firmware update
- Over-the-air key update
---|---
Power
|
U5B Power 5VDC
LED Indicator
| All LEDs off – button release to power down
Red LED on – device starting up / Charging battery
Red LED off – fully charged
Red LED flashing – low battery /Critical low battery
Blue LED on – Bluetooth is connected
Blue LED flashing – standby mode i waiting for connect Bluetooth or
Bluetooth is disconnected
NFC I ED indicator
| Connecting with POS terminal – First LED flashing Ready for NFC
Reading – First LED on
Success Reading – 4 LEDs on in consecutive order Transaction
Completed – One ‘BEEP” sound Errors – Two ‘BEEP’ sound
Power off – All LEDs off
Key Management|
DUKPT, MK/SK
Encryption Algorithm
| TDES
Support Operating System|
Android 2.1 or above
iOS 6.0 or above
Windows Phone 8
MS Windows
Operating Temperature
| 0″C – 45’C (321 – 113`F)
Operating Humidity|
Max 95%
Storage Temperature
| -20`C – 556C (-41 – 1311)
Storage Humidity|
Max 95%
FCC Caution Statement
FCC Supplier’s Declaration of Conformity:
BBPOS /TD200 (TD200W, TB200, TB200W, CHB2B, CHB2C, CHB2D)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
BBPOS Corp. 970 Reserve Drive, Suite 132 Roseville, CA 95678
www.bbpos.com
Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.
User shall use the supplied USB cable if an available port open on the
product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>