bbpos WisePOS E+ Vertual Terminal User Guide
- June 5, 2024
- bbpos
Table of Contents
bbpos WisePOS E+ Vertual Terminal
Index
Frontview
Rear View
Rear View (without battery cover)
CAUTION:
Please don’t point or damage the internal components when the back housing is
opened. Any intentional damage may void the warranty and cause the device to
malfunction.
Package Contents
- Device x1
- USB to DC cable x1
- Rechargeable battery x1
- Quick start guide x1
- Paper Roll x1
- Charging Cradle(optional) x1
Quick Start Guide
IMPORTANT:
Push and slide the battery door button to open the battery door of WisePOS E+
to insert the rechargeable battery into the battery compartment, SIM card, SAM
cards, and SD card to card slots properly, then lock the cover again for
battery charging via USB-DC cable before use.
- Push and Slide the battery door button.
- Open the battery door.
- Install SIM cards, SAM cards, and SD cards with your preference
- Install the battery
- Put the battery door back and lock it
- Turn on the device and configure the network setting. Once finished with the initial setup, tap on the BBPOS APP and follow in-APP instructions.
- Start your business with BBPOS APP.
- Start your business with BBPOS APP.
Change Paper Roll
- Open the Printer cover
- Replace the paper roll and close the Printer cover Make sure the paper roll size is 57 x Ø40mm “Make sure the paper roll direction is correct.
Charging Cradle (Optional)
- Charging Cradle Top View
- Charging Cradle Bottom View
Charge with Cradle
Cautions & Important Notes
- Please fully charge your WisePOS” E before use.
- Please ensure the magstripe /EMV chip of the card is facing the right direction when swiping or inserting the card.
- Don’t drop, disassemble, tear, open, crush, bend, deform, puncture, shred, microwave, incinerate, paint, or insert foreign objects into the device. Doing any of which will void the Warranty.
- Don’t immerse the device into water and place it near washbasins or any wet locations. Don’t spill any food or liquid on the device. Don’t attempt to dry the device with external heat sources, such as a microwave or hair dryer
- Don’t use any corrosive solvent or water to deans the device. Recommend using dry cloth to clean the surface only.
- Don’t use any sharp tools to point the internal components or connectors, which may lead to malfunction and void the Warranty.
- Don’t try to disassemble the device to repair it. Please contact your dealer for repair and maintenance.
- Only suitable use for the output DC 5V, 2000mA (max.) CE approval AC adapter, another electrical rating of AC adapter is prohibited.
Troubleshooting
FCC statement
Any user Changes authority or modifications to operate not the expressly
equipment. by the party responsible for compliance could void
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
ISED RSS Warning:
This device complies with Innovation, Science, and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
This device complies with ISED license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) the device may not cause interference, and (2) the user of the device must accept any interference received, even if the interference is likely to compromise the operation.
RF Exposure Information (FCC SAR):
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications
Commission of the US Government. The exposure standard for wireless devices
employs a unit of measurement known as the Specific Absorption Rate, or SAR.
The SAR limit set by the FCC is 1.6 W/kg. *Tests for SAR are conducted using
standard operating positions accepted by the FCC with the device transmitting
at its highest certified power level in all tested frequency bands. Although
the SAR is determined at the highest certified power level, the actual SAR
level of the device while operating can be well below the maximum value. This
is because the device is designed to operate at multiple power levels so as to
use only the power required to reach the network. In general, the closer you
are to a wireless base station antenna, the lower the power output.
The highest SAR value for the device as reported to the FCC when worn on the body, as described in this user guide, is 1.495W/kg (Body-worn measurements differ among devices, depending upon available enhancements and FCC requirements.) While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID: 2AB7XWISEPOSEPLUS.
For body-worn operation, this device has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and positions the device a minimum of mm from the body . The use of other enhancements may not ensure compliance with FCC RF exposure guidelines. If you do not use a body-worn accessory position the device a minimum of mm from your body when the device is switched on at its highest certified power level in all tested frequency bands. For handheld operating conditions, SAR meets with the FCC limit of 4.0W/kg.
RF Exposure Information (IC SAR):
This device meets the government’s requirements for exposure to radio waves.
This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by Innovation, Science, and
Economic Development Canada licence-exempt RSS standard(s). The exposure
standard for wireless devices employs a unit of measurement known as the
Specific Absorption Rate or SAR. The SAR limit set by the IC is 1.6 W/kg.
*Tests for SAR are conducted using standard operating positions accepted by
the IC with the device transmitting at its highest certified power level in
all tested frequency bands. Although the SAR is determined at the highest
certified power level, the actual SAR level of the device while operating can
be well below the maximum value. This is because the device is designed to
operate at multiple power levels so as to use only the poser required to reach
the network. In general, the closer you are to a wireless base station
antenna, the lower the power output.
The highest SAR value for the device as reported to the IC when worn on the body, as described in this user guide, is 1.495W/kg (Body-worn measurements differ among devices, depending upon available enhancements and IC requirements.) While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. The IC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the IC RF exposure guidelines. SAR information on this device is the IC: 24228-WPOSEPLUS.
For body-worn operation, this device has been tested and meets the IC RF exposure guidelines for use with an accessory that contains no metal and positions the device a minimum of 10 mm from the body . The use of other enhancements may not ensure compliance with IC RF exposure guidelines. If you do not use a body-worn accessory position the device a minimum of 10 mm from your body when the device is switched on at its highest certified power level in all tested frequency bands. For handheld operating conditions, SAR meets with an IC limit of 4.0W/kg.
Caution
Risk of explosion if the battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
Need Help
E: sales@bbpos.com T: +852 3158 2585
Room 1903-04, 19/F, Tower 2, Nina Tower, No. 8 Yeung Uk Road, Tsuen Wan, Hong Kong www.bbpos.com . o2019 BBPOS Limited. All rights reserved. BBPOS and WisePOS are either trademarked or registered trademarks of BBPOS Limited. i0S is the trademark of Apple Inc. Android is a trademark of Google Inc. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. The Bluetooth” word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by BBPOS Limited is under license. Other trademarks and trade names are those of their respective owners. Al details are subject to change without prior note.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>