EDISON M-7500 15-Inch Dual PA Speaker System User Manual
- June 6, 2024
- EDISON
Table of Contents
OPERATIONS MANUAL FOR EDISON PROFESSIONAL
M-7500
OPERATIONS MANUAL FOR EDISON PROFESSIONAL
Introduction:
Congratulations on your purchase of an M-7500 powered loudspeaker, engineered and manufactured by Britelite Enterprises. The M-7500 includes a high-output compression driver, and a 15″ woofer to produce an even, smooth studio-quality sound in a sound reinforcement speaker. Our design goal was to build a speaker with accurate playback, smooth dispersion of mid and high frequencies, and an ergonomic design for easy transport and setup. The result is a sound reinforcement system dynamic enough to use at home, in the studio, at parties, or in-home theater.
Features:
2-way amplified Active Speaker 2X15″ Long-throw woofer with high-temperature voice coil Ultra-wide, smooth dispersion of high and mid frequencies Mic/Line input and pass-thru connector USB & SD Card input supports .wav & MP3 Bluetooth Compatible with TWS LED lighting
Cautions:
- All Operating Instructions should be read before using this equipment.
- To reduce the risk of electrical shock, do not open this unit. There are NO REPLACEABLE PARTS INSIDE. Please refer servicing to a qualified service technician.
- Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
- This unit should only be cleaned with a damp cloth. Avoid solvents or other cleaning detergents.
- When moving this equipment, it should be placed in its original carton and packaging. This will reduce the risk of damage during transit.
- DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
- DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES
- Make sure All of your equipment is completely OFF and lower ALL VOLUME, LEVEL & GAIN controls before connecting a sound source.
- Only LINE LEVEL SIGNALS SHOULD BE SENT TO YOUR SPEAKER.
Disregarding any of the above will void your warranty!!!!
OPERATIONS MANUAL FOR EDISON PROFESSIONAL
-
MP3 module: Short press: Bluetooth, SD, USB, FM radio switch
Short press: REPEAT; Long press: EQ setting
Short press: Last and next; Long press: Volume – or +
Short press: Play or Pause; Long press: TWS -
Master volume: Control the Volume of the speaker
-
Treble volume: Control the Volume of treble
-
Bass volume: Control the Volume of bass
-
Line input volume: Control the Volume of line input
-
Microphone Volume: Control the Volume of the microphone input
-
Line input: XLR line input
-
Line output: an XLR line output
-
Microphone input: XLR microphone input microphone input
-
RCA line input
-
Microphone XLR input: 6.35 jack
-
Power Cord Connector
-
Power on/off
-
LED lighting on/off
-
115-230 voltage switch
How to make two M-7500 wireless stereo-link
- Long press “TWS” on the rear panel, two M-7500 will link automatically by Bluetooth
- Enable Bluetooth on your smartphone, select “EDISON PROFESSIONAL”
You can enjoy your music now with two M-7500
Please note that the second speaker is sold separately.
How to use M-7500 remote control
1 →
Power: Media player ON/OFF.
Stop Media player STOP. (Memory Card/ Flash Drive modes ONLY)
Mute: Media player MUTE.
2→
Mode: Media player MODE selection.
Repeat: Media player REPLAY mode selection.(memory card/flash drive modes
only)
EQ: Media player EQ mode selection. (memory card/flash drive modes only)
3→
Reverse: Media player REVERSE control.
Forward: Media player FORWARD control.
Play/Pause:Media player PLAY/PAUSE control.
4→
Master volume down: Adjusts speaker master volume DOWN.
Master volume up: Adjusts speaker master volume UP.
0: Media player track number and preset selection.
5→
1-9: Media player track number and preset selection.
How to switch the LED lighting of the speaker box
There is 5 mode of speaker box lighting, you can find the RED switch on the
rear panel, you can switch the mode which you prefer.
- Mode one: Multi-color automatically on when power on
- Mode two: Monocolour conversion
- Mode three: Monocolour run
- Mode three: Monocolour flash
- Mode three: LED lighting off
Placement Tips
-Avoid placing loudspeakers in the corners of a room. This increases the low-frequency output and can cause the sound to be muddy and indistinct.
-Avoid placing loudspeakers against a wall. This, too, increases the low-frequency output, though not as much as corner placement. However, if you do need to reinforce the low frequencies, this is a good way to do it.
-Avoid placing the active speakers directly on a hollow stage floor. A hollow stage can resonate at certain frequencies, causing peaks and dips in the frequency response of the room. It’s better to place the speakers on a sturdy table or tripod stand.
-Position the speakers so the high-frequency drivers are two to four feet above ear level to the audience to maintain high-frequency quality.
Troubleshooting
No Power
-First check to make sure the speaker is plugged into a live AC outlet.
Make sure the POWER switch is on.
No Sound
-Make sure input LEVEL control is turned up.
-Make sure the signal source is working and the connecting cables are in good shape and securely connected at both ends. Make sure the output volume control on the mixing console is turned up.
-Make sure the preamp or mixer does not have a Mute button engaged.
Bad Sound – Noise – Humming
If the sound is loud and distorted, verify that the levels are set properly on
the speaker and mixing console.
Make sure all connectors are secure and they are plugged into the proper
connector (i.e., Mic cable plugged into MIC input, Line level source plugged
into Line Level
Input. It is a good idea to periodically clean all electrical connections with
a non-lubricating electrical contact cleaner.
Make sure none of the signal cables are routed near AC cables, power
transformers or other electrical power cords.
If humming occurs, turn the LEVEL control of the speaker all the way down. If
the noise disappears, it’s coming from the signal source. If not, try
disconnecting the cable connected to the INPUT jack. If the noise disappears,
it could be a “ground loop,” Try the following ideas:
o, Use balanced connections throughout your system for best noise rejection.
(XLR cables, balanced ¼” jacks; RCA cables are not balanced)
o Whenever possible, plug all the audio equipment’s power cords into the same
outlet.
o The hum may appear when using an unbalanced source (CD player, iPod, etc.).
Use can use an RCA to XLR adapter to turn an unbalanced cable into a balanced
cable.
o If the hum persists, try removing components one at a time from the back of
the mixer and check each for hum. Reducing the Bass or Treble levels (10 and
11) may reduce humming.
Care and Maintenance
Your active speakers will provide many years of reliable service if you follow
these guidelines:
Avoid exposing the loudspeaker to moisture. If they are set up outdoors, be
sure they are undercover if you expect rain Avoid exposure to extreme cold. If
you must operate loudspeakers in a cold environment, warm up the voice coils
slowly by sending a low-level signal through them for about 15 minutes prior
to high-power operation.
Use a dry cloth to clean the cabinets. Only do this when the power is turned
off. Avoid getting moisture into any of the openings of the cabinet,
particularly where the drivers are located.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may
cause undesired operation.
FCC warning:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
IC warning
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
Limited Warranty
This Limited Product Warranty is provided by Britelite Enterprises. Britelite
warrants to A customer that the product is free from defects in materials and
workmanship under normal use during the Warranty Period of 90 days for parts
and 1-year labor. If the product fails to conform to the warranty then
Britelite or its authorized service will either repair or replace any non-
conforming product, provided that the Customer gives notice of noncompliance
within the Warranty Period to Britelite by emailing
service@britelite.net or calling
310-363-7110 (Mexico customers can call
0155 4624 0251). Please retain the original dated receipt as evidence of proof
of purchase.
Please do not return the product to the dealer or place of purchase.
Contact Britelite directly for warranty support.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>