rizoma PT508 Fox Plate Holder Kit Ducati Multistrada User Manual
- September 23, 2024
- rizoma
Table of Contents
Rizoma PT508 Fox Plate Holder Kit Ducati Multistrada
Specifications
- Product Name: Rizoma License Plate Holder
- Model Number: PT508
- Difficulty Level: Medium
- Assembly Time: 20-25 minutes
Product Usage Instructions:
Installation Steps:
- Disassemble Tail Fairings (Part Number: PT508)
- Install Rear Light
- Install Plate for Medium/Large License Plate
- Install Plate for Small License Plate
- Install Universal License Plate Holder
Maintenance:
Regularly inspect and maintain your Rizoma products. Check all related components of the motorbike after installation, and repeat these checks periodically, especially after long trips or prolonged periods of not using the bike. If any product is leaking, bent, deformed, cracked, chipped, or worn, have a Rizoma dealer inspect it before riding again. Never try to repair or modify the products; always replace them with Rizoma’s original components.
Compatibility:
Rizoma products may not be compatible with all motorcycles or aftermarket equipment. Contact your Rizoma dealer for guidance to ensure compatibility and safety.
Before you start mounting the product please check the completeness of the kit on the part list. The difficulty level and the time of assemblage shown do not include the removal of OEM components. Warning: Make sure that your motorbike is standing firmly before you start work, as a fall may lead to damage to the motorbike or injury to you or others, also make sure that the temperature of the exhausts and the engine are similar to the ambient temperature.
WARNING : TO CLEAN YOUR LICENSE PLATE DON’T USE DETERGENT, AGGRESSIVE PRODUCTS, OR ABRASIVE SPONGES THAT CAN DAMAGE OR SCRATCH YOUR LICENSE PLATE, BUT USE ONLY NEUTRAL DETERGENT WITH COLD WATER.
Attention: Improper installation could damage the motorcycle’s electrical system and cause a fire, resulting in personal injury or death. Electrical shock hazard. Disconnect the battery before installing the turn license plate bracket rear light or turn signals. The pins must always be isolated, and the polarity in the connections must be respected. The warranty is not valid for any electric wire cutting or any product modification or tampering.
Installation
DISASSEMBLE TAIL FAIRINGS
Step 1
INSTALL REAR LIGHT
Step 2
INSTALL PLATE FOR MEDIUM/LARGE LICENSE PLATE
Step 3
INSTALL PLATE FOR SMALL LICENSE PLATE
Step 4 INSTALL UNIVERSAL LICENSE PLAT
Step 5 INSTALL PIN OF POSITIONING
Step 6 INSTALL LICENSE PLATE
Step 7 INSTALL INDICATORS
Step 8 INSTALL LICENSE PLATE ON THE COVER
Step 9 ELECTRIC CONNECTIONS
Step 10
Step 11
Step 12
Step 13
Step 14
Step 15 TIGHTENING SCREW WITH BUSHINGS
Step 16
Warnings
Warnings: RIZOMA reserves the right, in its sole discretion, to make changes to the product and this information at any time and without prior notice. Although many catalogs and advertisements depict riders engaged in extreme or stunt riding, this activity is extremely dangerous, increases the risk of an accident, and increases the severity of any injury. The action depicted is performed by professionals under strictly controlled riding conditions. Only you know the limits of your riding ability and only you can control the conditions under which you ride. By and in consideration for his/her purchase and use of the RIZOMA product, the user expressly recognizes and agrees that in the event of any claim arising out of the use of this RIZOMA product, whether such claim is based on contract, warranty, tort (personal injury or wrongful death) or otherwise, the laws of the Republic of Italy shall apply and jurisdiction and venue for any such action shall be in the Courts of Busto Arsizio, Italy. All riders are strongly urged to take a motorcycle rider safety clinic. Always wear a properly fitted and fastened motorcycle helmet (RIZOMA recommends a full-face helmet), that has been approved by ANSI, SNELL, CE, or any other relevant authority, and any other safety equipment necessary for your riding styles, such as full-finger gloves, boots, and body armor. Be sure to read and follow all the instructions and warnings that originally accompanied your motorcycle, as well as the literature that accompanied any other parts installed on your motorcycle. Be sure that your tires are inflated to the correct pressure and that there is no damage whatsoever in the tread or sidewall of the tire.
Legal notes
Some of our products may not be approved for road circulation in the countries where homologation is required. Thus RIZOMA® srl declines any responsibility for a different use of its products.
FAQs
Q: What should I do if my Rizoma product is damaged?
A: If your product is leaking, bent, deformed, cracked, chipped, or worn, have a Rizoma dealer inspect it before riding again.
Q: Can I modify or repair Rizoma products?
A: Never try to repair or modify Rizoma products or their components. Always replace with Rizoma original components.
Q: How often should I inspect my Rizoma products?
A: The more you ride, the more often you must inspect your Rizoma products. Repeat checks periodically, especially after long trips or prolonged periods of not using the bike.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>