Sbo Hearing MI-AU5-MNR-T Aurora5 miniRITE T Radio Installation Guide
- June 6, 2024
- Sbo Hearing
Table of Contents
Radio Model – Quick Installation Guide
Radio Model Name: MI_AU5_MNR_T
Aurora5 miniRITE T Radio Model – 3D overview
The Aurora5 miniRITE T radio model (MI_AU5_MNR_T) contains two radio
transceivers running at 3.84 MHz and 2.4 GHz and both implemented on a single
hardware platform.
Additionally, a full featured RFID tag (IC5) operating at 865 MHz – 928 MHz
with internal antenna has been glued onto the PCB. The RFID tag has no
electrical connections related to the Aurora5 miniRITE T radio module.
The radio model is implemented in an engine module mounted on the main PCB
with connection to the antennas, telecoil, the microphones, the speaker and
the battery terminals. The radio model can be seen in 3D overview to the left.
The 3.84 MHz radio is a low power, short range inductive radio transceiver ( N
F M I – Near Field magnetic Induction ) working at a single channel at 3.84
MHz using MSK modulation with 320 kbit/s data rate and connected to a small
coil antenna.
The 2.4 GHz radio is a Bluetooth Low Energy (BLE core 5.1) transceiver using
GFSK modulation with 1 Mbit/s, 2 Mbit/s data rates, also capable of
proprietary reception modes (xBLE) with higher data rates (2 Mbit/s, 4 Mbit/s)
using 2FSK/4FSK modulation. The 2.4 GHz radio is connected to a short wire
antenna with a proprietary antenna connector.
Below the main flex PCB of the Aurora5 miniRITE T radio model with the most
important electrical and electro-mechanical components can be seen:
The most important part of the radio model is the Engine Module (IC1) mounted on the main flex PCB, which connects it to both the EEPROM memory and all external connections: On the top side these are the microphones, the battery terminals and the push button and coil antenna for the 3.84 MHz radio (L2).
The Aurora5 miniRITE T radio model requires only a single cell battery and an external speaker (also incl. the wire antenna for the Bluetooth radio part) to be attached and plastic shells, defining the industrial design of a hearing aid end product and holding everything together, in order to be operational.
On the bottom side of the main PCB of the Aurora5 miniRITE T radio model the
connector for the speaker unit assembly (where the wire antenna for the
Bluetooth radio is an integrated part), the programming connector, EEPROM
memory can be seen:
The most important parts inside the Engine module are a Digital-Signal- Processor (DSP), a radio Front-End (FE) chip for the 3.84 MHz radio part and an RF chip for the Bluetooth radio part – all mounted on a small rigid PCB again mounted on the main flex PCB. The Aurora5 miniRITE T radio model also includes all voltage regulators and buffered data programming inputs on board. The DSP is the main processor controlling the functionality of both radios in the Aurora5 miniRITE T radio model.
The Aurora5 miniRITE T radio model is intended to be installed in Oticon, Bernafon, Sonic, Philips and affiliated private labels wireless hearing aid devices of the miniRITE T (Receiver-In-The-Ear) wearing style.
Contains: FCC ID: 2ACAHAU5MNRT
IC: 11936A-AU5MNRT
NOTICE:
This device complies with Part 15, Part 15.223, Part 15.247 of the FCC Rules
and with RSS-210 and RSS-247 of Industry Canada.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made to this equipment not expressly approved by SBO Hearing A/S may void the FCC authorization to operate this equipment.
Description: Radio module with 2.4 GHz low power transceiver to be integrated
into various hearing instruments and associated devices.
Regulatory label:
| NB: The regulatory
label for Japan is also included in the IFU for Japan.
---|---
This device is granted pursuant to the Japanese Radio Law and the Japanese
Telecommunications Business Law under the grant ID 202- SMJ051
This device should not be modified (otherwise the granted designation number
will become invalid)
NB: The regulatory label is not shown on the radio module itself or any end products with it, since they are too small for the label to be readable without any optical aids or magnification. Below the radio module is shown, indicating a size of about 6x10x29 mm.
SBO Hearing A/S, Kongebakken 9, 2765 Smorum – DK-Denmark,
VAT-no.: DK39818558, www.sbohearing.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>