SCANCOOL XS 602 E Commercial Ice Cream Freezer User Manual
- June 6, 2024
- SCANCOOL
Table of Contents
XS 602 E
User manual
Scandomestic A/S
- DK-8600 Silkeborg
- Tel.: + 45 7242 5571
- www.scandomestic.dk
Important safety instructions
– Children shall not play with the appliance.
– Cleaning and user maintenance shall not be made by children without
supervision.
– Do not store explosive substances such as aerosol cans with a flammable
propellant in this appliance.
– If the supply cord is damaged, it must be replaced by the manufacturer or
its service agent or a similarly qualified person in order to avoid a hazard.
– Please according to local regulations regarding disposal of the appliance
for its flammable blowing gas.
Before you scrap the appliance, please take off the doors to prevent children
trapped.
– WARNING – Keep ventilation openings, in the appliance enclosure or in the
built-in structure, clear of obstruction.
– WARNING – Do not use mechanical devices or other means to accelerate the
defrosting process, other than those recommended by the manufacturer
– WARNING – Do not damage the refrigerant circuit.
– WARNING – Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the type recommended by the
manufacturer.
– Opening the door for long periods can cause a significant increase in the
temperature in the compartments of the appliance.
– Clean regular surfaces that can come in contact with food and accessible
drainage systems.
– Clean water tanks if they have not been used for 48 h; flush the water
system connected to a water supply if water has not been drawn for 5 days.
– Warning: Risk of fire / flammable materials, taking care to avoid causing a
fire by igniting flammable material.
– If the refrigerating appliance is left empty for long periods, switch off,
defrost, clean, dry, and leave the door open to prevent mold from developing
within the appliance.
– WARNING: When positioning the appliance, ensure the supply cord is not
trapped or damaged.
– WARNING: Do not locate multiple portable socket outlets or portable power
supplies at the rear of the appliance.
– This appliance is intended to be used in households and similar applications
such as
– staff kitchen areas in shops, offices, and other working environments;
– farmhouses and by clients in hotels, motels, and other residential type
environments;
– bed and breakfast type environments;
– Catering and similar non-retail applications.
– The appliance can be used by children aged 8 years and above and persons
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, if they have been given supervision or instruction concerning
use of the appliance in a safe way understand the hazards involved.
Correct Disposal of this product
This marking indicates that this product should not be disposed of with other
household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and
collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling.
-Warning: Risk of fire / flammable materials, taking care to avoid causing a fire by igniting flammable material.
| Warning: Risk of fire / flammable materials
---|---
Transportation and Placement
△When transporting the freezer showcase from one place to another, the
inclination of the cabinet should not exceed 45 degrees, for prevention
against compressor or system damage.
Before use, remove all the packing material. The backside of the refrigerator
should be placed to face to the wall and more than 20cm away from the wall,
both flank sides more than 20cm. Please prevent people touch hazardous
components of the back.
The freezer should be put in a well-ventilated, dry place. Don’t use it under
direct sunshine. The freezer should be kept away from the water sink, heat
source, and any volatile, corrosive material.
If the equipment cannot be used anymore, please do not throw it away freely,
it is necessary to be sent to a qualified organization for further
professional disposal.
Do not store explosive substances such as aerosol cans with a flammable
propellant in this appliance.
Power source and test-running
Single-phase power supply, 50Hz, voltage range 220~240V. If the voltage is
unstable, please install a voltage stabilizer with a capacity above 1000W.
Avoid turning on and off the power too frequently. If the power is turned off,
wait an interval of 5 minutes before turning it on again.
When the freezer will be out of use for a long time, disconnect the power
first, then clean it. Please examine the circuit whether it is excellent
before reuse.
Operation of the Temperature
When the screen shows “E0”, This means the problem of the temperature sensor.
The screen shows the temperature inside. When the compressor runs, the mark
“” shows on the screen.
When the compressor stops or the freezer make auto defrosting the mark “”
flashes.
Normal temperature setting.
1.1 Press the key “temperature -” and “temperature +” together for 3 seconds,
the screen shows “ST”, press the key “switch/set” , the screen shows the set
temperature.
1.2 Press the key“temperature -” to decrease the temperature, press the key
““temperature +” to increase the temperature. Temperature range is -12 degrees
to -30 degrees. Press the key “switch/set” to confirm the temperature needed.
The system would quit without any further operation within 10 seconds.
1.3 Press the key “switch/set” separately to control the LED light inside.
Parameter setting
2.1 Press the key “temperature +” and “switch/set” together for 3 seconds, the
screen shows “PO”
2.2 Press the key “switch/set” enter the password setting.
2.3 Press the key “temperature +” set the number as :55, then enter into the
parameter setting.
2.4 Press the key “temperature +” and “temperature -” to select the parameter.
2.5 Press the key “switch/set” to confirm the parameter series.
2.6 Press the key “temperature +” and “temperature -” to select the wanted
numbers
2.7 Press the key “switch/set” to save the data, the screen shows the
parameter series
2.8 Repeat 2.4~2.7 to set other parameters.
2.9 Press the key “switch/set” over 3 seconds, save the setting data, and quit
the setting system.
Temperature sensor
Parameter | description | nth) | max | default | |
---|---|---|---|---|---|
/0 | Temperature | ||||
sensor | 1 | 15 | 6 | ||
/1 | Temperature | ||||
sensor offset | -5.0 | S 0 | C | 0 | |
/2 | Defrost sensor | ||||
offset | -5.0 | 5.0 | C | 0 | |
/P | Number set | 0 | 1 | 1 |
Temperature setting
Parameter | description | min | ma \ | default | |
---|---|---|---|---|---|
St | Temperature set | rl | r2 | °C | -18 |
rl | set win temperature | -40 | r2 | °C | 8 |
r2 | set max temperature | rl | 85 | °C | -24 |
r3 | Work pattern | 0 | 1 | – | 0 |
rd | temperature difference | 0.1 | 10.0 | °C | 2.0 |
Compressor protection parameter
Parameter | description | min | max | default | |
---|---|---|---|---|---|
c0 | Compressor running time-lapse after plug in | 0 | 99 | Min |
cl | Min time of compressor stops | 0 | 99 | Min | 10 |
---|---|---|---|---|---|
c3 | Max time of compressor running | 0 | 10 | Hour | 5 |
c4 | Compressor work time | ||||
after sensor problem | 0 | 99 | Min | 40 | |
c5 | Compressor stop time | ||||
after sensor problem | 1 | 99 | Min | 10 | |
ct | Compressor problem | ||||
judge time | 1 | 6 | Hour | 5 | |
c2 | Compressor problem | ||||
stop time | 0 | 199 | Min | 30 | |
cu | Compressor problem judged temperature difference | 0 | 10.0 | C | 0.5 |
Cc | Plug in forced running time | 0 | 99 | Min | S |
Defrosting
Parameter | description | nun | max | default | |
---|---|---|---|---|---|
dO | Defrost pattern | 0 | 1 | 1 | |
dl | defrost circle | 0 | 199 | Hour | 14 |
dp | Max time for defrosting | 1 | 99 | Min | 35 |
d2 | Compressor stop time | ||||
after defrosting starts | 0 | 60 | Min | 5 | |
d6 | Defrost shows | 0 | 2 | 1 | |
d7 | Temperature alters defrost | 0 | 50 | oC | 30 |
dd | Water flow time | 0 | 15 | Min | 15 |
d8 | Higher temperature alarm shield time after defrost | 0 | 99 | Min | 30 |
Alarm codes
Alarm | description |
---|---|
E0 | Temperature sensor error |
E1 | Defrost sensor error |
Food storage
There must be space between the foods stored in the cabinet, between the foods
and the inner surface of the cabinet, so as to keep good ventilation of cold
air and freeze evenly. Do not put in any bottled or canned beverage with a
freezing point above the temperature in the cabinet when it is below zero.
For foods that should be moisture-free or lose water easily, wrap them up with
hermetical food bags or fresh films before putting in the cabinet for the sake
of avoiding smell-mixing and reducing frosting.
Storage of volatile and combustible gases, liquids such as strong alkalies,
strong acids, petrol, etc. are forbidden.
Maintenance
The freezer should be cleaned regularly. When cleaning, turn off the power,
take out the foods in the cabinet, clean the inside using water or a little
neutral detergent.
Do not use boiling water, acid, chemical diluents, petrol, oil, or dirt-
removing powder.
Dry it after cleaning.
Use light soap water when cleaning the door seal, apply a little of talcum
powder on it after natural drying to extend its service life.
Use a soft cloth with water or a little detergent to clean the out surface.
Note, keeping the power supply and lower part of connecting wires away from
water to avoid electricity leakage.
Except for common breakdowns, those who are not service technicians should not
take apart and repair the freezer on their own so as to avoid worsening the
trouble. Unauthorized repair of an electrical part such as compressor,
temperature controller is forbidden.
Defrosting
Defrost for better freezing efficiency when the frost film in the cabinet is
4-5mm thick.
When defrosting, turn off the power, take out the frozen foods, open the door
for warming and melting. Use a soft cloth to absorb water and clean it up.
Do not use sharp metal tools such as steel brushes to clean the frost film
when defrosting so as to avoid evaporator damage.
Troubleshooting
Breakdown | Case | Removal method |
---|
The indicator is not on.
The compressor does not start.| The plug isn’t connected to the socket
really.| reinsert it.
no power| Connect the socket with power.
The indicator is on , but the corn- pressor doesn’t work and buzzes only| The
power voltage is<187V.| Put a power regulator of more than 1000W power
together.
The compressor stops a minute after the start, restart after a few minutes,
and so repeatedly.| The power voltage is>242V.
The compressor works normally, but the temperature in the cabinet lowers too
slowly.| The door is opened too frequently.| Reduce open times.
The food in the cabinet is too much and placed improperly.| Place foods
properly keep place between them for ventilation of cold air.
The frost film is too thick.| Take out foods and defrost.
The surface of the condenser is too dirty.| Stop and clean the condenser.
The door seals badly.| Adjust the door seal.
The noise is too loud| The freezer is placed unstably.| Place it stably.
The fusing of the freezer is loose.| Tighten the fixing.
there’s contact between pipes.| Separate them.
The following are not faults:
When the freezer is working or after is stops for a while, the refrigerant in
the pipes is cycling and gives out"running water"sounds.
The surface temperature of the compressor may be up 70℃~80℃ when it is
working.
The backside of the step freezer gives out heat.
In the rainy season, the outer surface of the cabinet may have dew, which
makes no defects on normal use. Just dry it with a piece of cloth.
Warranty Information
The manufacturer provides a warranty in accordance with the legislation of the
customer’s own country of residence, with a minimum of 1 year (Germany: 2
years), starting from the date on which the appliance is sold to the end-user.
The warranty only covers defects in material or workmanship.
The repairs under warranty may only be carried out by an authorized service
center. When making a claim under the warranty, the original bill of purchase
(with purchase date) must be submitted.
The warranty will not apply in cases of:
– Normal wear and tear
– Incorrect use, e.g. overloading of the appliance, use of non-approved
accessories
– Use of force, damage caused by external influences
– Damage caused by non-observance of the user manual, e.g. connection to an
unsuitable mains supply or non-compliance with the installation instructions
– Partially or completely dismantled appliances
Access to professional repairs, such as internet webpages, addresses, contact
details.
Model no: XS 602 E
Aftersales service station list:
Address | Scandomestic A/S |
---|---|
Contact Number | 72425571 |
Website | Scandomestic.dk |
QR code | 366765 |
Relevant information for ordering spare parts, directly or through other
channels provided by the manufacturer, importer or authorized representative;|
Scandomestic A/S
The minimum period during which spare parts, necessary for the repair of the
appliance, are available;| 8 years
Instruction on how to find the model information in the product database, as
defined in Regulation (EU) 2019/2024 by means of a weblink that links to the
model information as stored in the product database or a link to the product
database and information on how to find the model identifier on the product.)|
www.scandomestic.dk
Note: The address or contact phone number of the service site is subject to change without prior notice. Please confirm whether the service station is a directly affiliated one of our company when requiring services.
EU DECLARATION OF CONFORMITY
Ref. Ares In accordance with
ISO 17050-1:2004
Model number (unique identification of the product): | XS 602 E |
---|---|
Name and address of the manufacturer or his authorized representative: |
Scandomestic A/S Ilan) 20
8600 Silkeborg
Denmark
This declaration of conformity is issued under the sole responsibility of the
manufacturer (or installer):| Scandomestic A/S Unavej 20
8600 Silkeborg
Denmark
The object of the declaration (identification of product allowing
traceability. It may include a color image of sufficient clarity to enable the
identification of the product, where appropriate.)
Product: Ice Cream Freezer Brand: Scancool
Colour: White
Model name: XS 602 E|
The object of the declaration described in point 4 is in conformity with the
relevant Union harmonization legislation:| EN 61000-3-2
References to the relevant harmonized standards used, or references to the
specifications in relation to which conformity is declared:| ISO 23953-1:2015,
ISO 23953-2:2015,
2014/30/Eu, EN 55014-1:2006+A1:2009 +A2:2011, EN 55014-2:1997+A1:2001+A2:2008,
EN 61000-3-2:2014, EN 61000-3-3: 2013, MD 2006/42/Ec, EN
60335-1:2012+A11:2014, EN 60335-2-89:2010, EN 62233:2008, (EU) 2017/1369, (EU)
No. 2019/2018, (EU) No. 2019/2024, 2011/65/Eu, 2002/96/Ec, 2014/35/Ec,
2014/30/Eu
Where applicable: the notified body … (name, number)… performed … (description
of intervention)… and issued the certificate:| RoHS 2011/65/Eu
Additional information:| Commercial Box
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>