i Safe MOBILE M120A01 IS120.1 Mobile Phone Instructions

i Safe MOBILE M120A01 IS120.1 Mobile Phone

EX MARKINGS

• ATEX:
  • II 2G Ex ib IIC T4 Gb
  • II 2D Ex ib IIIC T135°C Db
  • EU Type Examination Certificate: EPS 21 ATEX 1 107 X
  • CE-designation: 2004
• IECEx:
  • Ex ib IIC T4 Gb
  • Ex ib IIIC T135°C Db
  • IECEx Certificate: IECEx EPS 21.0040X
• UKEX:
  • II 2G Ex ib IIC T4 Gb
  • II 2D Ex ib IIIC T135°C Db
  • CML 21UKEX21329X UKCA-designation: 2503
• Temperature range:
  • – 20°C … +60°C (EN/IEC 60079-0)
  • – 10°C … +50°C (EN/IEC 62368-1)
• Manufactured by:
  • i.safe MOBILE GmbH
  • i_Park Tauberfranken 10 97922 Lauda-Koenigshofen Germany

EX-RELEVANT SAFETY REGULATIONS

Use of this device assumes that the operator observes the conventional safety regulations and has read and understood Operating Manual, Safety Instructions and certificate. When used in explosion hazardous areas, the following Safety Instructions must also be complied with:

• Inside explosion hazardous areas the covers of all interfaces (USB) must be closed.
• To ensure the IP-protection, it has to be ensured that the all gaskets are present and functi-onal. There must be no large gap between the two halves of the housing and between the battery compartment cover and housing.
• The device may only be charged outside explosion hazardous areas using the i.safe PROTEC-TOR 1.0 Micro USB Cable or other equipment approved by i.safe MOBILE GmbH.
• The device may only be charged at temperatures between +5 °C to +35 °C.
• Physical connections to to IS120.1 are only allowed outside explosion hazardous areas using the i.safe PROTECTOR 1.0 Micro USB Cable or other equipment approved by i.safe MOBILE GmbH.
• The device may not be exposed to any aggressive acids or alkalis.
• The device may only be used in zones 1 or 21.

INFORMATION CONCERNING SAR CERTIFICATION (SPECIFIC ABSORBATION RATE)

The SAR limit of Europe is 2,0 W/kg for the head and body, 4,0 W/kg for the limbs. The device has been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0,72 W/kg and when correctly worn on the body is 1,44 W/kg, limbs is 3,08 W/kg.

This device was tested for typical body worn operations with the back of the handset kept 5 mm from the body. The device complies with RF specifications when used at 5 mm from the body. Belt clips, holsters and similar accessories used should not contain metallic components in the assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements, and should be avoided.

Restrictions in the 5 GHz band:

According to Article 10 (10) of Directive 2014/53/EU, the packaging shows that this radio equipment will be subject to some restrictions when placed on the market in Belgium The WLAN function for this device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range.

MAXIMUM OUTPUT POWER

EU/UK-DECLARATION OF CONFORMITY

EU/UK – Declaration of Conformity
EU/UK – Konformitätserklärung
according to directive 2014/34/EU, SI 2016 No. 1107, 2014/53/EU, SI 2017 No. 1206, 2011/65/EU (2015/863/EU), SI 2012 No. 3032
nach Richtlinie 2014/34/EU, 2016 No. 1107, 2014/53/EU, SI 2017 No. 1206, 2011/65/EU
(2015/863/EU), SI 2012 No. 3032
The company i.safe MOBILE GmbH declares under its sole responsibility that the product to which this declaration relates is in accordance with the provisions of the following data, directives and standards:
Die Firma i.safe MOBILE GmbH erklärt in alleiniger Verantwortung, dass Ihr Produkt auf welches sich diese Erklärung bezieht, den nachfolgenden Daten, Richtlinien und Normen entspricht:

Name & address of the manufacturer in the EU Name & Anschrift des Herstellers innerhalb der europäischen Gemeinschaft| i.safe MOBILE GmbH i_Park Tauberfranken 10

97922 Lauda – Koenigshofen

Germany

---|---
Description of the devices

Beschreibung der Geräte

| Mobile Phone type / Typ : IS120.1

model / Modell : M120A01

Ex – marking

Ex – Kennzeichnung

| II 2G Ex ib IIC T4 Gb

II 2D Ex ib IIIC T135°C Db IP6X

Type examination certificate 2014/34/EU issued by

Baumusterprüfbescheinigung 2014/34/EU ausgestellt durch

| EPS 21 ATEX 1 107 X

__

Bureau Veritas Consumer Product Services Germany GmbH

Businesspark A96

86842 Tuerkheim, Germany

identification number / Kenn-Nummer : 2004

Applied harmonized standards

Angewandte harmonisierte Standards

| EN IEC 60079-0:2018; EN60079-11:2012
Type examination certificate SI 2016 No. 1107

issued by

Baumusterprüfbescheinigung SI 2016 No. 1107 ausgestellt durch

| CML 21UKEX21329X

__

Erofins E&E CML Limited,

Newport Business Park, New Port Road, Ellesmere Port,

CH65 4LZ, United Kingdom

identification number / Kenn-Nummer : 2503

Applied standards

Angewandte Standards

| EN IEC 60079-0:2018; EN60079-11:2012
Conformity statement 2014/53/EU issued by| MiCOM Labs Inc.
---|---
Konformitätsaussage 2014/53/EU ausgestellt| 575 Boulder Court,
durch| Pleasanton, California 94566
 | USA
 | identification number / Kenn-Nummer : 2280
Applied harmonized standards| EN IEC 62368-1:2020+A11:2020;
Angewandte harmonisierte Standards| EN 50663:2017; EN 62479:2010;
 | EN 50566:2017; EN 62209-1:2016;
 | EN 62209-2:2010/A1:2019
 | EN 50360:2017;
 | Draft EN 301 489-52 V1.1.2;
 | Draft EN 301 489-19 V2.2.0;
 | EN 301 489-17 V3.2.4;
 | Draft EN 301 489-3 V2.1.2;
 | EN 301 489-1 V2.2.3;
 | EN 55032:2015+A1:2020+A11:2020;
 | EN 55035:2017+A11:2020;
 | EN IEC 61000-3-2:2019;
 | EN 61000-3-3:2013+A1:2019;
 | EN 300 328 V2.2.2;
 | EN 301 893 V2.1.1;
 | EN 300 440 V2.2.1;
 | EN 303 413 V1.2.1;
 | EN 301 511 V12.5.1;
 | EN 301 908-1 V13.1.1;
 | EN 301 908-2 V11.1.2;
 | EN 301 908-13 V13.1.1;
Conformity statement SI 2017 No. 1206 issued| MiCOM Labs Inc.
by| 575 Boulder Court,
Konformitätsaussage SI 2017 No. 1206| Pleasanton, California 94566
ausgestellt durch| USA
 | identification number / Kenn-Nummer : 2280

Applied standards

| ****

EN IEC 62368-1:2020+A11:2020;

Angewandte Standards| EN 62209-1:2016;
 | EN 62209-2:2010/A1:2019
 | EN 50360:2017;
 | EN 50566:2017;
 | EN 50663:2017;
 | EN 62479:2010;
 | Draft EN 301 489-52 V1.1.2;
 | Draft EN 301 489-19 V2.2.0;
 | EN 301 489-17 V3.2.4;
 | Draft EN 301 489-3 V2.1.2;
 | EN 301 489-1 V2.2.3;
 | BS EN 55032:2015+A1:2020+A11:2020;
---|---
BS EN 55035:2017+A11:2020;
BS EN IEC 61000-3-2:2019;
BS EN 61000-3-3:2013+A1:2019;
EN 300 328 V2.2.2;
EN 301 893 V2.1.1;
EN 300 440 V2.2.1;
EN 303 413 V1.2.1;
EN 301 511 V12.5.1;
EN 301 908-1 V13.1.1;
EN 301 908-2 V11.1.2;
EN 301 908-13 V13.1.1;
Conformity statement 2015/863/EU amending| Shenzhen TCT Testing Technology Co., Ltd.
2011/65/EU issued by| TCT testing Industrial Park,
Konformitätsaussage 2015/863/EU ergänzt| Fuquiao 5th Industrial Zone,
2011/65/EU ausgestellt durch| Fuhai Street,
 | Shenzhen, China
Applied harmonized standards| IEC 62321-2: 2013; IEC 62321-3-1: 2013;
Angewandte harmonisierte Standards| IEC 62321-5: 2013;
 | IEC 62321-4: 2013 + A1: 2017;
 | IEC 62321-7-1: 2015; IEC 62321-7-2: 2017;
 | IEC 62321-6: 2015; IEC 62321-8: 2017
Conformity statement SI 2012 No. 3032 issued| Shenzhen TCT Testing Technology Co., Ltd.
by| TCT testing Industrial Park,
Konformitätsaussage SI 2012 No. 3032| Fuquiao 5th Industrial Zone,
ausgestellt durch| Fuhai Street,
 | Shenzhen, China
Applied standards| BS EN 62321-2: 2014;
Angewandte Standards| BS EN 62321-3-1: 2014;
 | BS EN 62321-5: 2014;
 | BS EN 62321-4: 2014 + AMD1: 2017;
 | BS EN 62321-7-1: 2015;
 | BS EN 62321-7-2: 2017;
 | BS EN 62321-6: 2015;
 | BS EN 62321-8: 2017
CE/UKCA Marking

CE/UKCA-Kennzeichnung

|

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>