Skindfense K9 Pro Plus Temperature Scanner and Gel Sanitizer Dispenser User Manual

Skindfense K9 Pro Plus Temperature Scanner and Gel Sanitizer Dispenser User Manual

Appearance

Specifications

1. Accuracy: +/-0.2°F (Place the K9 in the operating environment 30 minutes before use to ensure accuracy)
2. Alarm type: Flashing + Beeping (“DIDIDI”)
3. Measuring distance: .75-3.1 inches (2-8 cm)
4. LED Display: Number
5. Interface: USB Type-C
6. Bottle Capacity: 1,200 mL
7. Mounting Type: Wall hanging, desktop stand, floor stand
8. Working Temperature: 50°-104°F (59°95°F recommended)
9. Measuring Range: 32-122°F
10. Response Time: 500 Ms
11. Standby Time: 5s for non-working, dynamic loop with white light
12. Power Supply: DC 5V 2,000mA (or 4 AA batteries)
13. Dimensions: 4.8×5.19×12.2 inch (122x132x310 mm)
14. Liquid Type: Hand Sanitizer or Liquid Disinfectant

Display

1. Standby: the white dot on the bottom of right corner flashing in sequence. [Fig. 1]
2. Normal Temperature: Displays current temperature and green light flashes once on the display [Fig. 2]
3. Abnormal Temperature: Displays current temperature and red light flashes once on the display [Fig. 3]
4. Out of measuring range (Note: does not spray hand sanitizer): “Lo”: Ultra low temperature alarm. [Fig. 4] “Hi”: Ultra-high temperature alarm. [Fig. 5]

Instructions

1. Temperature measurement and hand sanitizing: Place your hand on the bottom until you hear a “Di” sound and the K9 announces either “Normal Temperature” or “Please Retest.” The LED will display the temperature and dispense the hand sanitizer. [Fig. 6]

2. Button Functions: (1) Function Setting. [Fig. 7] (2) Specific Function Setting. [Fig. 8]

3. Function Setting: Press button 1 once to set the temperature unit.
   Press button 2 to switch between C: Celsius or F: Fahrenheit. [Fig. 9, Fig. 10]

4. Machine Self-Cleaning Mode: Put water in the K9 Pro Plus and press and hold buttons 1 and 2 for 5 seconds. Pump will cycle for 10 seconds.

5. Press the button 1 2 times to set the working mode Press the 2 to switch the working mode: : body mode; : surface mode [Fig. 11]

6. Press the button 1 3 times to set the alarm temperature Press the 2 to switch the alarm temperature between 99.1° to 102.2° F

7. Press the button 1 4 times to set the alert volume Press the 2 to switch the volume rom V0 to V4

8. Press the button 1 5 times to set the language Press the 2 to select the language [Fig. 12]:

9. Press the button 1 6 times to set the amount of sanitizer dispensed Press the 2 to set the extrusion time between 0.1 and 2.0 seconds [Fig. 13]

10. Press the button 1 for 2 seconds or more: ON/OFF

11. After you have completed adjusting any of the settings above, press the 1 button until the screen shows 00.0. The settings are complete and the K9 Pro Plus is ready to operate [Fig. 14]

Mounting

Batteries

1. Remove Back Panel: Depress the tabs at the top of the unit [Fig. 20]
2. Insert Batteries: Use (4) AAA batteries [Fig. 21]

Adding Liquid

1. Unscrew the top cap: Use the included flexible, compact funnel to add sanitizer [Fig. 22]

Warnings

1. Do not pour hand sanitizer into the K9 Pro Plus temperature measurement probe and proximity sensor.
2. Make sure the K9 Pro Plus is standing upright after filling it with hand sanitizer
3. When first used, put your hand under the sensing area 5-8 times until the liquid flows freely
4. Do not use sticky, or extremely thick liquid. The tube inside the machine will be easily blocked. Remember to fill the machine with water and use the self-clean mode to clean the machine from time to time

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>