telldus 14189 Remote Controlled Indoor Outlet User Manual

June 6, 2024
TELLDUS

telldus logo

telldus 14189 Remote Controlled Indoor Outlet

telldus 14189 Remote Controlled Indoor Outlet image

Connect to a remote control

STEP 1

  1. Press 7 sec
  2. Blink (15s)telldus 14189 Remote Controlled Indoor Outlet fig1

STEP 2

  1. Within 15 sec
  2. <CLICK,telldus 14189 Remote Controlled Indoor Outlet fig2 Remote Control only included in selected packages

Connect sensor to TellStick

Requires a TellStick and a Telldus Live account

STEP 1

live.telldus.com

Click on Devices icon telldus 14189 Remote Controlled Indoor Outlet
fig3

STEP 2

Add a new devicetelldus 14189 Remote Controlled Indoor Outlet
fig4

STEP 3

Add new device wizard
Select your device type:telldus 14189 Remote Controlled Indoor Outlet
fig5

STEP 4

Select your device brand:telldus 14189 Remote Controlled Indoor Outlet
fig6

STEP 5

Select your device model:telldus 14189 Remote Controlled Indoor Outlet
fig7

STEP 6

Enter name and press next button telldus 14189 Remote Controlled Indoor
Outlet fig8Any name may be used/Valfritt namn/Valgfritt namn/Nimi on vapaa valinta/Jeder Name kann verwendet werden

STEP 7telldus 14189 Remote Controlled Indoor Outlet
fig9

STEP 8

  1. Add new device wizard

  2. Install the outlet as explained under “Installation” in the manual.

  3. Keep the outlet programming button pressed for 7 seconds. The LED blinks slowly.

  4. Press the learn button below within 15 seconds to link the outlet. (The programming mode is automatically disabled if no pairing signal is received.)

  5. The connected lamp blinks three times as confirmation.telldus 14189 Remote Controlled Indoor Outlet fig10

  6. Learn
    If the paring fails, repeat steps 2-4 again. The distance to the receiver may have to be shorter when pairing than during ordinary use.

  7. Done

STEP 9telldus 14189 Remote Controlled Indoor Outlet
fig11

Remote controlled outlets & remote control

  • Remote control* has 3 channels and 1 group function.
  • Each outlet has 5 memory settings.
  • Blue LED indicates ON/OFF and programming status.

Installation

  • Remove the plastic tab from the battery in the remote control*.
  • Connect the outlet to mains power.
  • Connect a lamp to the outlet. If there is a power switch on the connecting cable make sure it is switched on.

Unpair a single remote control* from an outlet

  • Keep the button on the outlet pressed for 7 seconds. The LED blinks slowly.
  • Press the corresponding OFF button on the remote control* to remove the learned code (the learning mode is automati-cally disabled after 15 seconds if no button is pressed).
  • The connected lamp blinks three times as confirmation.

Unpair all remote controls* from an outlet

  • Keep the button on the outlet pressed for 7 seconds. The LED blinks slowly.
  • Within 7 seconds, press the button briefly once more (the learning mode is automatically disabled after 15 seconds if no button is pressed).
  • The connected lamp blinks three times as confirmation.

Specifications

  • Article number: 14189
  • Battery: 3V CR2032
  • Max resistive load: 3680 W
  • Range: 0-30m
  • Protection class: IP20
  • Protection class: I
  • Operating temperature: 0°C–35°C
  • Power supply: 230 V~, 50 Hz
  • Standby power: <1 W

Correct disposal of the products

Within the European Union, this symbol indicates that the products must not be disposed in the household waste. Devices contain valuable recyclable materials that should be recycled for reuse and uncontrolled waste disposal may cause harm to the environment and human health. Please dispose the old products via suitable collection systems or send the unit to the office where you bought it. This will make the product recycling.

Proove Distribution AB
Birger Svensson Väg 34 B
432 40 Varberg, Sweden
www.telldus.com 
support.telldus.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals