Doozoler B0CBTMCYJ5 Thermostatic Shower System Installation Guide

SHOWER
INSTALLATION MANUAL

B0CBTMCYJ5 Thermostatic Shower System

| Hot Water
---|---
| Cold Water
| Mixed Water

INSTALLATION CONSIDERATIONS

1. Please read over these instructions thoroughly before beginning installation.
   Make sure that you have all tools and supplies needed to complete the installation.

2. For best results, we recommends that this unit be installed by a licensed, professional plumber.

3. Make sure inlet pipes and supply valves have been installed and cleaned, also ensure no impurities in pipeline.

4. After installation, check all joints for leakages.

TOOLS REQUIRED

PRODUCT LIST

INSTALL SHOWER VALVE

Dimensions reserved for installation of faucet body.

Pipe schematic diagram
Connect hot & cold water pipe and other pipes. After that, open the water to test is all pipes have leakage or not. At last, seal the wall.Remove the shower valve knob from the brass valve body and then install the panel on to the valve body. Screw the knobs into the handwheels.

SHOWER PARTS IDENTIFICATION DIAGRAM

INSTALL HEAD SHOWER

STEP1: Measure the head shower size STEP 2: Install f ix frameMark the position and drill the hole on the above which corresponded to the hung ceiling frame.
Use the screw knife tightening the screw and fixed the frame.
STEP 3: Remove the assemble frame Remove the assemble frame on the back of the head shower by the allen key.
STEP 4: Install the screw pump Tighten the screw pump on the fix frame and then install the shower head assemble frame on the screw pump.
STEP 5: Install shower
Fix the shower head on the assemble frame. STEP 6: Test the water

STEP 7: Assemble connection shown

NOTE : Picture assemble just for reference, please determine the installation height according to the actual situation.

LED REMOTE CONTROL

1 Turn On / Standby
Press this key to turn on unit or switch to standby mode.The power or unit will automaticly turn on and restore to previous status.
2/9 Dynamic Mode Adjust
Switch to dynamic mode from static color, or switch between dynamic modes.
3/10 Dynamic Speed Adjust
Adjust dynamic playing speed. Press SPEED+ to increase speed and press SPEED- to decrease. Unit will switch to dynamic mode if press this key at static color mode.
4/5 Static Color Adjust
Switch to static color mode from dynamic mode, or switch between static colors.
6 Direct Color Select
Shortcut key to static colors. When press the specific color key, LED will play the same static color. The direct colors are included in COLOR+ and COLOR- operation.
7/8 Brightness Adjust
Adjust static color brightness. Press BRIGHT+ to increase brightness and press BRIGHT – to decrease. Unit will switch to static color mode. If press this key at dynamic mode.
11 Demo Mode
Press this key will switch to Demo mode. At demo mode, it plays 17 dynamic modes in loop, each mode repeat 3 times.
NOTE: For proper receiving remote signal, please do not install the main unit in closed metal parts.
Pairing New Remote
The remote and main unit is 1 to 1 paired as default. Further more, main unit can be paired to 3 remote controllers and each remote controller can be paired to any main unit.
Please do following steps to pair new remote controller.

1. Plug off the power of main unit and plug in after 5 seconds.
2. Press SPEED- and SPEED+ key together in 5 seconds after power on. After this operation, the main unit will recognize the new remote controller.

Free Remote Pairing Mode
In some specific cases, the main unit may need to be paired to any remote
controllers. Please plug off the power of main unit and plug in after 5 seconds.

CARE AND MAINTENANCE

1. Modern faucets and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality.

2. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the warranty.

3. To remove lime scale, use only products made specifically for that purpose.
   Always follow the manufacturer’s instructions when using.

4. Do not use cleaners that contain hydrochloric, formic, acetic, or phosphoric acids, as these will cause considerable damage to finishes and to plastic components.

5. Never use cleaners containing abrasives. Do not use abrasive cleaning cloths, pads, or sponges.

6. Clean your faucets and shower products as and when required. Regular cleaning will prevent scale buildup and water spotting.

7. When using spray cleaners, spray first onto a sponge or cloth, do not spray directly onto the product.

8. After cleaning, rinse thoroughly with clear water to remove any cleaner residue.

9. Soap and shampoo residue can also cause damage to the product. Rinse well with clean water after use.

10. If the surface is already damaged, harsh cleaning materials will cause further damage.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>