AVE PAR64-TRI18 1W Tri Color LED Light User Manual
- June 6, 2024
- AVE
Table of Contents
**AVE PAR64-TRI18 1W Tri Color LED Light User Manual
**
Safety
Important Safety Information
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT OVEREXPOSE THIS FIXTURE TO RAIN OR MOISTURE.
WARNING: CONNECT ONLY TO MAINS POWER SUPPLY WITH A PROTECTIVE EARTHING CONNECTION.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE REAR COVER OR ATTEMPT TO OPEN THE LIGHTING FIXTURE. THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
- Read this manual carefully.
- Keep this manual safe for future reference.
- Follow all warnings and recommendations.
- Do not operate or store near water.
- Do not expose the fixture to dripping or splashing liquid, and ensure that no objects containing liquid are placed on this fixture.
- Clean only with a dry cloth.
- Do not install or operate near any heat sources such as radiators, gas heaters, stoves, or other heating apparatus.
- Only use attachments and accessories specified by the manufacturer.
- Do not block any ventilation openings, including sound ports.
- Install in accordance with the manufacturer’s instructions.
- Do not obstruct or remove the ground plug from the fixture, doing so may cause electric shock resulting in serious injury or death.
- Protect the power cord from being walked on, pinched, or rolled over.
- Unplug the fixture during electrical storms and power outages.
- Refer all servicing to a qualified service technician. Servicing is required when the fixture no longer operates, fails to power on, or emits an electrical smell or sound.
- To completely disconnect AC power from this fixture, the power supply cord must be unplugged.
Precautions
If an AVE lighting fixture is used outdoors on a sunny day, ensure that it is in a shaded area and is well ventilated to help prevent overheating.
Do not use AVE lighting fixtures in environments that are below 0°C OR exceed +40°C.
Suspension
Suspending any object is potentially dangerous and should only be attempted by qualified individuals with thorough knowledge of the techniques and regulations for suspending objects. It is the responsibility of the installer to ensure all fixtures and effects are installed correctly. AVE strongly recommends inspecting installed systems every 6 months for signs of weakness or damage.
If any damage or weakness is detected then remedial action should be taken immediately. The user is responsible for making sure the wall, ceiling, or structure is capable of supporting all objects suspended overhead. Any hardware used to suspend the fixture not associated with AVE is the responsibility of others.
Description
The AVE PAR64-TRI18 is a lightweight and high-output LED par with classic par chassis design.
Featuring 18x 1W LED diodes each with a Red, Green, Blue (3-in-1) configuration allowing you to mix a huge colour spectrum without any colour shadowing. The par is built into a light metal housing with thermal fan to keep the fixture cool. Also included is a yoke for hanging the par from stands, or lighting truss systems.
The PAR64-TRI18 is supplied out of the box with ‘Auto’ programs including a ‘sound active’ mode for plug-and-play operation with an amazing visual effect. The LED par can also be controlled via DMX for integration into larger lighting shows and setups with the 3-pin XLR connectors.
Features
- High-output 18x 1W LEDs
- 3-in-1 RGB diodes for great colour mixing
- Lightweight ‘stubby par’ housing
- 3-Pin XLR connections for DMX control
- Built-in Auto programs; Fade / Flash / Sound
- Static colour settings
- Master / Slave operation
Setup
To set up your AVE PAR64-TRI18 follow the below steps;
- Mount the item on your lighting stand or on the floor
- Connect the AC power cord to a grounded mains 240v power source
- Turn the power source on
- Select the desired operation mode and press enter
Mounting
The PAR64-TRI18 is fitted with a yoke that can be attached to a floor stand for use on flat & sturdy surfaces.
For hanging the fixture to a lighting stand or trussing, simply attach a lighting clamp to the yoke, ensuring that the clamp is tightened to prevent unwanted movement.
Operation
To access the menus and functions of the PAR64-TRI18, use the four (4) buttons located under the main control screen.
| Button Label | Function |
|---|---|
| Menu | Press to access main menu, or change function once the fixture is |
on
Up| Cycles upwards through the menu and options
Down| Cycles downwards through the menu and options
Enter| Press to select a menu option or save a setting
Menu Map
Main
Level
| Program Level| Description
---|---|---
Addr| 1 – 512| DMX Address Value
Chnd| 3Ch| 3 Channel DMX Mode
7Ch| 7 Channel DMX Mode
SLnd| nASt| Master
SL1| Slave Mode 1
SL2| Slave Mode2
SL3| Slave Mode3
SL4| Slave Mode4
Shnd| SoUn| Sound Active Mode
Auto| Auto Programs
Colo| Co 1 – Co 7| Static Colours
Stro| Strobe Speed 0-255
FAdE| SP 1 – SP8 (speed)| Colour Fade
LED| On/Off| | LED backlight Display
dISP| On/Off| Reverse Display
Nanu| red| 0-255| Manual Red Colour 0 – 255
| Gree| 0-255| Manual Green Colour 0 – 255
| bLue| 0-255| Manual Blue Colour 0 – 255
teSt| red| | Manual Red Colour 0 – 255
Gree| | Manual Green Colour 0 – 255
bLue| | Manual Blue Colour 0 – 255
FhrS| | | Displays hours of operation
DMX Channels
- 3 CH Control
1 CH| Red
---|---
2 CH| Green
3 CH| Blue - 7 CH Control
1 CH| 0 – 255| Red
---|---|---
2 CH| 0 – 255| Green
3 CH| 0 – 255| Blue
4 CH| 0 – 255| Dimmer
5 CH| 0 – 255| Strobe (slow > fast)
6 CH| 0 – 7| No Function
| 8 – 255| Colour Stepping Colour
7 CH| 0 – 7 No Function
8 – 199 Auto Colour (slow > fast)
200 – 255 Sound Active
Specifications
Light Source: 18 x 1W LED Diodes
Diode Colours: Red, Green, Blue (3-in-1)
Beam Angle : 24°
DMX Channels: 3CH / 7CH
DMX Connectors: 3-Pin XLR
Enclosure: Metal Alloy
Power Consumption: 30W
Power Supply: 240V AC / 50Hz
Power Connectors: IEC Mains
Dimensions: 260 x 260 x 360 mm
Weight: 1.0 kg
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>