AVE LED-PAR64B LED RGB Parcan User Manual
- June 6, 2024
- AVE
Table of Contents
LED-PAR64B
User Manual
Safety
Important Safety Information
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT OVEREXPOSE
THIS FIXTURE TO RAIN OR MOISTURE.
WARNING: CONNECT ONLY TO MAINS POWER SUPPLY WITH A PROTECTIVE EARTHING
CONNECTION.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE REAR
COVER OR ATTEMPT TO OPEN THE LIGHTING FIXTURE. THERE ARE NO USER-SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
- Read this manual carefully.
- Keep this manual safe for future reference.
- Follow all warnings and recommendations.
- Do not operate or store near water.
- Do not expose the fixture to dripping or splashing liquid, and ensure that no objects containing liquid are placed on this fixture.
- Clean only with a dry cloth.
- Do not install or operate near any heat sources such as radiators, gas heaters, stoves, or other heating apparatus.
- Only use attachments and accessories specified by the manufacturer.
- Do not block any ventilation openings, including sound ports.
- Install in accordance with the manufacturer’s instructions.
- Do not obstruct or remove the ground plug from the fixture, doing so may cause electric shock resulting in serious injury or death.
- Protect the power cord from being walked on, pinched, or rolled over.
- Unplug the fixture during electrical storms and power outages.
- Refer all servicing to a qualified service technician. Servicing is required when the fixture no longer operates, fails to power on, or emits an electrical smell or sound.
- To completely disconnect AC power from this fixture, the power supply cord must be unplugged.
Precautions
If an AVE lighting fixture is used outdoors on a sunny day, ensure that it is
in a shaded area and is well ventilated to help prevent overheating.
Do not use AVE lighting fixtures in environments that are below 0°C OR exceed
+40°C.
Suspension
Suspending any object is potentially dangerous and should only be attempted by qualified individuals with thorough knowledge of the techniques and regulations for suspending objects. It is the responsibility of the installer to ensure all fixtures and effects are installed correctly. AVE strongly recommends inspecting installed systems every 6 months for signs of weakness or damage. If any damage or weakness is detected then remedial action should be taken immediately. The user is responsible for making sure the wall, ceiling, or structure is capable of supporting all objects suspended overhead. Any hardware used to suspend the fixture not associated with AVE is the responsibility of others.
Description
The LED-PAR64B is a cost-effective LED wash light for your stage or
dancefloor. Powered by 150 x 10mm LED diodes (50 Red, 50 Blue, 50 Green) with
a classic ‘stubby’ par design. Out of the box the LEDPar64B includes built-in
color and auto modes including color fades, sound to light, and flashing
functions. It can also be easily controlled via DMX for use with larger
lighting shows and create more dynamic effects and colors.
The LED-PAR64B is supplied out of the box with ‘Auto’ programs including a
‘sound active’ mode for plug-and-play operation with an amazing visual effect.
The LED-PAR64B can also be controlled via DMX for integration into larger
lighting shows and setups with the 3-pin XLR connectors.
Features
- Ultra-low power consumption
- Sound activated, auto and color fade modes
- DMX 512 compatible
- 150x Super bright 10mm LEDs
- Easy to navigate digital display
Setup
To set up your AVE LED-PAR64B follow the below steps;
- Mount the item on your lighting stand or on the floor
- Connect the AC power cord to a grounded mains 240v power source
- Turn the power source on
- Select the desired operation mode and press enter
Mounting
The LED-PAR64B is fitted with a yoke that can be attached to a floor stand for
use on flat & sturdy surfaces.
For hanging the fixture to a lighting stand or trussing, simply attach a
lighting clamp to the yoke, ensuring that the clamp is tightened to prevent
unwanted movement.
Operation
To access the menus and functions of the LED-PAR64B, use the four (4) buttons located under the main control screen.
Button Label | Function |
---|---|
Menu | Press to access main menu, or change function once the fixture is |
on
Up| Cycles upwards through the menu and options
Down| Cycles downwards through the menu and options
Enter| Press to select a menu option or save a setting
---|---
Menu Map
Main Level | Program Level | Description |
---|---|---|
Addr | 1 – 512 | DMX Address Value |
SOUF | Sound Mode 1 | |
SOUA | Sound Mode 2 | |
NSC | NS1 – NS12 | Auto Modes |
FAdE | FA00 – FA12 | Colour Fade (slow to fast) |
FLAS | FL00 – FL12 | Colour Jump (slow to fast) |
BL | BL00 – BL12 | Manual Blue Colour 0 – 12 |
gL | gL00 – gL12 | Manual Green Colour 0 – 12 |
rL | rL00 – rL12 | Manual Red Colour 0 – 12 |
DMX Channels
7 CH Control
1 CH | 0 – 255 | Dimmer |
---|---|---|
2 CH | 0 – 255 | Red |
3 CH | 0 – 255 | Green |
4 CH | 0 – 255 | Blue |
5 CH | 0 – 255 | Strobe (slow > fast) |
6 CH | 0 – 7 | No Function |
8 – 199 | Auto Colour (slow > fast) | |
0 – 255 | Strobe (slow > fast) | |
7 CH | 0 – 7 | No Function |
8 – 255 | Colour Stepping |
Specifications
Light Source: | 150 x 10mm LED Diodes |
---|---|
Diode Colours: | 50x Red, 50x Green, 50x Blue |
DMX Channels: | 7CH |
DMX Connectors: | 3-Pin XLR |
Enclosure: | Metal Alloy |
Power Consumption: | 18W |
Power Supply: | 240V AC / 50Hz |
Power Connectors: | Fixed main plug |
Dimensions: | 260 x 260 x 360 mm |
Weight: | 1.0 kg |