AVE HEX-FLAT18 18x 12W LED Par Can User Manual
- June 6, 2024
- AVE
Table of Contents
AVE HEX-FLAT18 18x 12W LED Par Can
Safety
Important Safety Information
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT OVEREXPOSE
THIS FIXTURE TO RAIN OR MOISTURE.
WARNING: CONNECT ONLY TO MAINS POWER SUPPLY WITH A PROTECTIVE EARTHING
CONNECTION.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE THE REAR
COVER OR ATTEMPT TO OPEN THE LIGHTING FIXTURE. THERE ARE NO USER-SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
- Read this manual carefully.
- Keep this manual safe for future reference.
- Follow all warnings and recommendations.
- Do not operate or store near water.
- Do not expose the fixture to dripping or splashing liquid, and ensure that no objects containing liquid are placed on this fixture.
- Clean only with a dry cloth.
- Do not install or operate near any heat sources such as radiators, gas heaters, stoves, or other heating apparatus.
- Only use attachments and accessories specified by the manufacturer.
- Do not block any ventilation openings, including sound ports.
- Install in accordance with the manufacturer’s instructions.
- Do not obstruct or remove the ground plug from the fixture, doing so may cause electric shock resulting in serious injury or death
- Protect the power cord from being walked on, pinched, or rolled over.
- Unplug the fixture during electrical storms and power outages.
- Refer all servicing to a qualified service technician. Servicing is required when the fixture no longer operates, fails to power on, or emits an electrical smell or sound.
- To completely disconnect AC power from this fixture, the power supply cord must be unplugged.
Precautions
If an AVE lighting fixture is used outdoors on a sunny day, ensure that it is
in a shaded area and is well ventilated to help prevent overheating. Do not
use AVE lighting fixtures in environments that are below 0°C OR exceed +40°C.
Suspension
Suspending any object is potentially dangerous and should only be attempted by qualified individuals with thorough knowledge of the techniques and regulations for suspending objects. It is the responsibility of the installer to ensure all fixtures and effects are installed correctly. AVE strongly recommends inspecting installed systems every 6 months for signs of weakness or damage. If any damage or weakness is detected then remedial action should be taken immediately. The user is responsible for making sure the wall, ceiling, or structure is capable of supporting all objects suspended overhead. Any hardware used to suspend the fixture not associated with AVE is the responsibility of others.
Description
The AVE Hex-Flat 18 is a high-powered LED par can that is designed to wash even the largest of stages. Fitted with 18x 12W Osram LED diodes, each with Hex-colour technology (RGBAW+UV) allowing you to mix any colour in the spectrum. The par is built into a solid ABS plastic housing with thermal fan to keep the fixture cool. A dual yoke is also included for safely hanging the fixture from stands or lighting truss, and can be split for mounting on the floor.
The Hex-Flat 18 used a digital LCD menu display that is easy to read (even in
low light environments) and includes Auto’ programs such as
Fade’ and `Sound
active’ modes as standard. Easy to use right out of the box with manual colour
mixing from the menu without any additional hardware needed. The Hex-Flat 18
can also be controlled via DMX for integration into larger lighting shows and
setups with the 3-pin XLR connectors and the 8CH or 11CH personalities.
The Hex-Flat also has the ability (when used in DMX) to default to an auto
setting when the DMX signal is no longer detected. When the DMX resumes the
fixture returns to the DMX setting. This is useful for dance floors, and event
venues that want to avoid unexpected blackouts due to signal loss or
controller issues.
The Hex-Flat 18 is the perfect fixture for venues, concerts, production
companies and anyone needing a powerful and versatile colour wash.
Features
-
High-output 18x 12W LEDs
-
Hex Colour diodes (RGBAW+UV) for great colour spectrum mixing
-
Strong ABS housing with integrated cooling fan
-
Digital LCD display with high contrast
-
3-Pin XLR connections for DMX control
Built-in Auto programs; Fade / Auto / Sound -
Static colours directly from the menu
-
Master / Slave operation
-
Fitted with a Dual Yoke
Setup
To set up your AVE Hex-Flat 18 follow the below steps
- Mount the item on your lighting stand or on the floor
- Connect the AC power cord from a grounded mains 240v power source.
- Power the fixture/s on from the mains socket
- Select the desired operation mode and press enter, select the mode again and wait apporx 1min for the setting to save.
Power Linking
The Hex-Flat is fitted with a Mains IEC input and output that allows you to power multiple fixtures from one (1) mains power connection. To power link your fixtures;
- Ensure the mains power is off and unplugged from the wall
- Connect your IEC extension cable to the output connector from the first fixture and connect to the power input of the second unit ensuring that the connector are firmly in place
- Repeat step 2 for each additional fixture up to 7 fixtures
Mounting
The Hex-Flat 18 is fitted with a Dual yoke that can be separated and used as a floor stand for use on flat & sturdy surfaces. For hanging the fixture to a lighting stand or trussing, simply attach a lighting clamp to the outer yoke, ensuring that the clamp is tightened to prevent unwanted movement.
Operation
To access the menus and functions of the Hex-Flat 18, use the four (4) buttons located under the main control screen.
Button Label | Function |
---|---|
Menu | Press to access main menu, or change function once the fixture is |
on
Up| Cycles upwards through the menu and options
Down| Cycles downwards through the menu and options
Enter| Press to select a menu option or save a setting
Menu Map
Main Level | Program Level | Description |
---|---|---|
DMX Address | 1 – 512 | DMX Address Value |
Channl Mode | 8 CH | 8 Channel DMX Mode |
11 CH | 11 Channel DMX Mode | |
Slave Mode | Master | Master |
Slave | Slave Mode | |
Show Mode | Sound | Sound Active Mode |
Auto | Auto Mode | |
Sound Sense | 0 – 100 | Sound Mode Mic Sensitivity |
Fade Speed | 1 – 10 | Colour Fade Speed (fast > slow) |
Color Select | 1 – 33 | Select preset colours |
Manul Color | Red | Red Colour 0 – 255 |
Green | Green Colour 0 – 255 | |
Blue | Blue Colour 0 – 255 | |
White | White Colour 0 – 255 | |
Y | Amber Colour 0 – 255 | |
P | UV Colour 0 – 255 | |
Strobe Show | 0 – 131 | Manual Strobe (slow > fast) |
132 – 139 | No Function | |
140 – 181 | Strobe Effect 1 (fast > slow) | |
182 – 231 | Strobe Effect 2 (fast > slow) | |
232 – 255 | Random Strobe Pulse | |
Back Light | On / Off | Turns screen on/off |
Display Invert | No / Yes | Inverts the Ddisplay |
Balance Setup | Red | Red Balance 0 – 255 |
Green | Green Balance 0 – 255 | |
Blue | Blue Balance 0 – 255 | |
Language Setup | English / Chinese | |
Temperature | – | Displays the fixture temperature |
Auto Test | – | Tests all functions and colours |
DMX Channels
8 CH Control
1 CH | 0 – 255 | Dimmer |
---|---|---|
2 CH | 0 – 255 | Strobe |
3 CH | 0 – 255 | Red |
4 CH | 0 – 255 | Green |
5 CH | 0 – 255 | Blu e |
6 CH | 0 – 255 | White |
7 CH | 0 – 255 | A m b er |
8CH | 0 – 255 | U V |
11 CH Control
1 CH | 0 – 255 | Dimmer |
---|---|---|
2 CH | 0 – 255 | Red |
3 CH | 0 – 255 | Green |
4 CH | 0 – 255 | Blue |
5 CH | 0 – 255 | White |
6 CH | 0 – 255 | A m b er |
7 CH | 0 – 255 | U V |
8 CH | 0 –255 | C o l o u r |
9 CH | 0 – 7 |
8 – 99
100 – 149
150 – 199
200 – 245
246 – 255
| No Function
Strobe (slow > fast) Strobe (fast > slow) Strobe Effect 1
Strobe Effect 2
S trobe (max speed)
10 CH| 0 –255
8 – 255
| No Function
S tepping Colour
11 CH| 0 – 7| No Function
| 8 – 199| Stepping Colour Speed
| 200 – 255| S o un d Active
SPECIFICATIONS
Light Source: | 18 x 12W Hex-Colour LED Diodes |
---|---|
Diode Colour: | Red, Green, Blue, White, Amber, UV |
Beam Angle: | 36° |
DMX Channels: | 8CH / 11CH |
DMX Connectors: | 3-Pin XLR |
Enclosure: | ABS Plastic |
Power Consumption: | 220W |
Power Supply: | 240V AC / 50Hz |
Power Connectors: | IEC Mains |
Dimensions: | 325 x 330 x 100 mm |
Weight: | 2.50 kg |
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>