VICTROLA TT42 Bluetooth Turntable Instruction Manual
- June 6, 2024
- Victrola
Table of Contents
Bluetooth Turntable
MODEL: TT42 INSTRUCTION MANUAL
PLEASE READ THIS INSTRUCTION MANUAL CAREFULLY BEFORE USE AND KEEP IT FOR
FUTURE REFERENCE.
WARNING
- Always follow basic safety precautions when using this appliance, especially when children are present.
- Children should be supervised to ensure that they do not play with the appliance
- Do not damage the power cord, neither do not place any heavy objects on it, do not stretch it or bend it. Also do not attach extension cables. Damage to the power cord may occur fire or electric shock.
- If the supply cord is damaged, it must be replaced by the manufacturer, a service agent or similarly qualified persons in order to avoid a hazard.
- Ensure that the unit is plugged into an AC 100-240V 50/60Hz power outlet. Using higher voltage may cause the unit to malfunction or even catch fire.
- If the power plug does not fit into your outlet, do not force the plug into an electrical socket if it does not fit.
- Turn off the unit before unplugging it from the power source to completely switch it off.
- Do not disconnect or connect the power cord with wet hands. It may cause an electric shock.
- Ensure that the mains plug is always easily accessible.
- This product does not contain any parts that are serviceable by the user. In case of a fault, contact the manufacturer or authorized service department. Exposing the internal parts inside the device may endanger your life. The manufacturer’s guarantee does not extend to faults caused by repairs carried out by unauthorized third parties.
- Do not use this product immediately after unpacking. Wait until it warms up to room temperature before using it.
- Ensure this product is used in moderate climates only (not in tropical/subtropical climates).
- Place product on a flat, stable surface that is not subject to vibrations.
- Ensure the product and its parts are not overhanging the edge of the supporting furniture.
- To reduce the risk of fire, electric shock or damage to this product, do not expose it to direct sunlight, dust, rain and moisture. Never expose it to dripping or splashing and do not place objects filled with liquids on or near the product.
- Do not place objects filled with liquids, such as vases, on the apparatus.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- Do not place the product where the humidity is high and ventilation is poor.
- Don’t mount this product on a wall or ceiling.
- Do not place the unit near TVs, speakers and other objects that generate strong magnetic fields.
- Do not leave the unit unattended when in use.
- Allow at least 30 cm clearance from the rear and the top of the unit and 5 cm from each side. Always ensure that the ventilation openings are not covered with items such as newspapers, tablecloths, curtains, etc.
- NEVER let anyone, especially children, pushes anything into holes, slots or any other openings in the unit’s casing as this could result in a fatal electric shock.
- Storms are dangerous for all-electric appliances If the main or aerial wiring is struck by lightning, the appliance might get damaged, even if it is tumed off. You should disconnect all the cables and connectors of the appliance before a storm.
- Excessive sound pressure from headphones can cause hearing loss.
- Do not cover ventilation openings, this is not intended to be used on soft support. MAINTENANCE
- Unplug the power cable from the power source before cleaning the appliance.
- Use a soft and clean rag to clean the outside of the unit. Never clean it with chemicals or detergent.
SAFETY INSTRUCTIONS
POWER ADAPTER
- To disconnect the unit from the main supply, unplug the lead from the main socket.
- Only use the supplied main adaptor, as failure to do this may result in safety risk and/or damage to the unit.
- The main plug of the power adaptor is used as the disconnect device. The socket outlet shall be installed near the equipment and shall be easily accessible.
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Please read these safety instructions and respect the following warnings before the appliance is operated:
| AC voltage
---|---
DC voltage Class
equipment
For indoor use only
Energy efficiency marking with level VI gs
The polarity of the D.C. power connector
-
ACCESSORIES INCLUDEDThe shown above appears on electrical and electronic equipment (or the packaging) to remind users of this.
-
Users are requested to use existing return facilities for used equipment and batteries. ****
-
INSTRUCTION MANUAL
-
WARRANTY (BACK OF MANUAL)
-
POWER ADAPTOR
PRODUCT OVERVIEW
Front View
-
POWER: Press to turn the unit ON or OFF.
-
BT OUT: Press to activate the Bluetooth output function.
-
PLAY/PAUSE (
Press to start playback, press again to pause.
Long press the button for 3 seconds to disconnect the Bluetooth pairing.
(NOTE: This button only works in Bluetooth mode.) -
PREVIOUS ( ) Skip to the previous track or station.
-
NEXT (
Skip to the next track or station. -
Display Screen
-
5mm EARPHONE JACK: Accepts headphone/earphone plugs.
-
BT/PHONO KNOB: Turn to select BT/PHONO mode.
-
VOLUME KNOB: Turn to adjust volume.
-
LINE OUT jacks For amplifier device with RCA auxiliary input sockets, insert the white and red plugs on the RCA cable into the unit. Insert the opposite end into the amplifier device. Be sure to connect the white plug to the white jack and the red plug to the red jack.
-
DC Input Jack Connect the power adapter to the jack to power on the unit.
Part of the Turntable
-
Turntable
-
45 RPM adapter
-
Tone Arm holder
-
Cue Lever: Before use, gently push the Tone Arm holder to the right to release the TONEARM.
-
AUTO STOP ON/OFF SWITCH: Switch “ON”, the turntable will stop automatically when finish playing. Switch “OFF”, the turntable will keep turning when finished playing.
-
Speed Selector
-
Tone Arm
-
STYLUS
SETUP/BASIC OPERATION
Setup 1. Remove white protective needle cover by gently pulling towards the
front of the unit. 2. Remove any packaging materials from the unit. 3. Connect
the power adapter to the DC Input jack to power on the unit.
Note : – It is strongly recommended that this product should be operated
only from the type of power source indicated on the marking label.
Basic Operation
- Press the POWER button to turn the unit on.
- Select mode by turning the BT/PHONO KNOB.
- Rotate the VOLUME KNOB to adjust to the desired sound level.
Listening through RCA LINE OUT
For amplifier device listening, first reduce the volume level to a minimum.
Insert the white and red plugs on the RCA cable into the unit, then insert the
opposite end into the amplifier device. Be sure to connect the white plug to
the white jack and the red plug to the red jack.
Listening through Earphones/Headphones (not included)
For private listening, first, reduce the volume level to a minimum. Insert
your headphones’ plug into the 3.5mm jack, then adjust the volume up by
turning the VOLUME KNOB.
Note : The speakers will automatically be deactivated while headphones
are plugged in.
CONDENSATION WARNING:
When the unit is moved from a cold or warm place or is used following a sudden
temperature change, there is the danger that water vapor in the air may
condense on the unit, preventing proper operation. In such cases, leave the
unit for 1-2 hours after plugging it into an AC outlet to allow it to
stabilize at the temperature of its surroundings.
VINYL RECORD OPERATION
-
Turn the unit ON by pressing the POWER button.
-
Turn the BT/PHONO KNOB to enter the PHONO mode.
-
Gently open the dust cover.
-
Put the record on the turntable. Select the speed. When playing a 45 RPM record, use the included 45 adaptors.
-
Gently push the Tone Arm holder to the right to release the TONEARM.
-
Raise the Cue Lever to lift the TONEARM off the tonearm support.
-
Move the TONEARM gently to the edge of the record (or the starting point of the track). The turntable will begin to turn.
-
Gently lower the TONEARM by slowly releasing the CUE LEVER. You can lower the TONEARM manually if the CUE LEVER has not been raised.
-
Turn the VOLUME KNOB to adjust the volume.
-
When playback has finished, slightly lift the tonearm using the CUE LEVER and return it to the TONEARM holder.
BLUETOOTH OPERATION
An external device with Bluetooth Connectivity can be wirelessly connected to this turntable using the Bluetooth Function.
GETTING CONNECTED USING BLUETOOTH
- Turn the BT/PHONO KNOB to select BT mode. The “bt” will flash on the Display Screen.
- Turn your external devices’ Bluetooth Setting ON. Wait a moment, then look for the Bluetooth Pairing name ” TT42C ” NOTE: The effective distance between your external device and this unit is 10 meters ).
- Select the Bluetooth pairing name, to connect the unit. Once connected the “bt” on the Display Screen will stop flashing.
- Select the music media files on your external device, then press the PLAY/PAUSE button ( ) to begin playback.
- To temporarily pause playback, press the PLAY/PAUSE button (*ii ) when playback. Press again to resume.
- To skip to the previous or the next tracks, press the PREVIOUS/NEXT button ( 144 or ►► 1 to listen.
BLUETOOTH-OUT OPERATION
The product supports Bluetooth wireless connection (BT-OUT). It can be connected with external Bluetooth-compatible headphones (not included) and Bluetooth speakers (not included).
- When playing your vinyl record, press the BT OUT button.
- The “ ” icon flashes on the Display Screen.
- Turn ON your external Bluetooth receiver device (such as Bluetooth headphones and Bluetooth Speakers) and set to pairing mode.
- Wait for 5-20 seconds, they will make connections to each other automatically.
- The ” * ” icon stops flashing once successfully paired.
- Control the playback from your BT speaker. (You can only adjust the volume from your external Bluetooth device.)
• Place the Bluetooth device within lm (3.3′) of the product to perform pairing correctly.
• The product stays in the pairing mode for about 30 seconds. If pairing is not properly completed, follow the above steps again from the beginning after turning all devices OFF. • “BT OUT” is only compatible with vinyl record playback.
MAINTENANCE/PROPER HANDLING
Handling Vinyl Records
- Do not touch the record’s grooves. Only handle records by the edges or the label with clean hands. Touching the record surface will cause your record’s quality to deteriorate.
- To clean a record, use a soft anti-static cloth to gently wipe the record surface.
- Keep records in their protective sleeves when not in use.
- Always store records upright on their edges.
- Avoid placing records in direct sunlight, close to a heat source (radiators, stoves, etc.), or in a location subject to vibration, excessive dust, heat, cold or moisture.
How to Replace the Turntable Stylus (Replacement Stylus # ATN3600L)
Removing the Stylus from the Cartridge
- Place your fingers at the tip of the stylus and push down to the direction “A”. WARNING: When applying force to stylus, too much may damage or break the cartridge.
- Pull the stylus out toward the direction “B”.
Install the Stylus
- Hold the tip of the stylus and insert the other edge by pressing toward direction “C”.
- Push the stylus up toward direction “D” until it locks at the tip.
Caution :
- Do not remove or bend the stylus needle.
- Do not touch the needle to avoid injury to your hand.
- Turn off the unit’s power before you replace the stylus.
- Keep out of reach of children.
Please note: The stylus should last about 300 hours under normal use. It is recommended that the stylus be replaced as soon as you notice a change in sound quality. 78 RPM records may accelerate stylus wear and may have to be changed sooner
SPECIFICATIONS
GENERAL
Power adapter—————— 9V/1. 5A Power Consumption ———— 13.5W
Power Output ——————-2 x 5W Size—————————–12.7″ (322mm) W x 12.3″ (312mm) D x
5.2″ (131mm)
H Weight ————————–4.5 lbs (2kg) Operating Temperature ——— 5°C – + 40°C
RECORD PLAYER
Speeds ————————-33-1/3 RPM, 45 RPM and 78 RPM
BLUETOOTH Bluetooth Version—————V5.1
Bluetooth Profiles —————A2DP,
AVRCP Bluetooth Frequency range —–2.402GHz-2.480GHz
Operating Distance————– 10 meters (33 ft.)
ADAPTOR
Manufacturer——————– DONGGUAN HP-POWER
TECHNOLOGY.LIMITED Model —————————HP18A-0901500-AU
Auto Standby mode
After 15 minutes without any audio input, the device will automatically switch
into standby mode. Please follow up the instruction manual to resume the
operations.
TROUBLESHOOTING GUIDE
| Symptom| Possible Cause| Solution
---|---|---|---
BLUETOOTH| •No sound| •The unit is not switched to Bluetooth mode,
•Your device’s and/or your unit’s volume is not turn up.
•Your device is too far from the unit or there’s some obstacle between your
device and your unit.| •Ensure the unit is switched to BT mode.
•Move your Bluetooth device closer to the unit.
•Turn up the volume on your portable device and/or the unit.
•Turn OFF your Bluetooth device and unit. Then power them both back ON.
•Sound has a lot of static| •Your device is too far away.| •Bring your device
closer to the turntable.
•Unable to pair with a Bluetooth device| •Your device doesn’t have Bluetooth
connectivity.
•The Bluetooth pairing is not successful| •Confirm that your device is
Bluetooth compatible.
•Re-pair the unit and device again.
BT-OUT| •The connection takes too long| •The time of connection depends on the
connecting device| •Wait for a moment
•Turn OFF your Bluetooth device and unit. Then power them both back ON.
ONOHd| •Decline in turntable
audio performance| •The turntable stylus is worn out.| •Replace the stylus.
GENERAL| •Unit will not power on| •Unit is unplugged.| •Connect the DC power
adapter to the jack.
•No sound output from speakers| •The volume level is set too low.
•The input selector does not match the playback source.| •Adjust the volume.
•Select the correct input source.
•Noise/Distortion in sound output| •The unit is too close to a TV set or
another interfering device,| •Turn off the TV or other appliance, and relocate
the unit.
•Unit fails to respond| •It might result from external factors such as ESD
(Electro-static discharge).| •Disconnect the power cord and external audio
device. Re-plug the power cord after one minute.
FCC STATEMENTS
Caution : The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment. This device complies with Part 15
of the FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE : This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radiofTV technician for help.
FCC& IC Radiation Exposure Statement: This equipment complies with FCC and
Canada radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with a minimum distance of
20cm between the radiator and your body. This transmitter must not be co-
located or operating in conjunction with any other antenna or transmitter.
WARRANTY INFORMATION
Victrola is a registered trademark of Innovative Technology Electronics LLC.
Innovative Technology Electronics LLC. (IT) warrants the product to be free
from “Defects” in materials under normal use for a period of “One Year from
the date of the original purchase. The Warranty is “Not” transferable. IT
agrees, within the initial “One Year” period, to replace the product if it is
determined to be defective at “No Charge’ or offer a merchandise credit if
proof of purchase is provided or if the original product is no longer in
stock. It is further agreed that IT will cover the cost to repair or replace
damaged “Parts” only for a total period of “One Year” from the date of the
original purchase. The warranty does not cover cosmetic damage, antennas, AC
cords, cabinets, headbands, ear pads, or damage due to line power surges,
connection to an improper voltage supply or setting, misuse, mishandling,
accident, acts of God or attempted repair by an unauthorized service agent.
Repair or Replacement as provided under this warranty is the exclusive remedy
of the customer, (IT) shall not be liable for any incidental or consequential
damages for breach of any implied warranty on this product except to the
extent prohibited by applicable law. Any implied warranty of merchantability
or fitness for a particular purpose on this product is limited in duration to
the duration of this warranty.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty lasts,
so the above exclusions or limitations may not apply to you. This warranty
gives you specific legal rights and you may also have other rights, which vary
from state to state.
Contact Website: www.victrola.com/support
Phone: 877-483-2497
(Monday – Friday, 10am – 6pm, EST)