HiKOKI DS36DA Multi Volt Cordless Driver Drill Instruction Manual

: October 27, 2023
: HiKOKI

Table of Contents

DS36DA Multi Volt Cordless Driver Drill
GENERAL POWER TOOL SAFETY WARNINGS
CORDLESS DRIVER DRILL / COMBI DRILL SAFETY WARNINGS
ADDITIONAL SAFETY WARNINGS
REGARDING LITHIUM-ION BATTERY TRANSPORTATION
SYMBOLS
STANDARD ACCESSORIES
SPECIFICATIONS
CHARGING
MOUNTING AND OPERATION
REACTIVE FORCE CONTROL
MAINTENANCE AND INSPECTION
TROUBLESHOOTING
Read User Manual Online (PDF format)
Download This Manual (PDF format)

DS 36DA・DV 36DA

DS36DA Multi Volt Cordless Driver Drill

HiKOKI DS36DA Multi Volt Cordless Driver Drill -

Handling instructions

HiKOKI DS36DA Multi Volt Cordless Driver Drill -fig1

HiKOKI DS36DA Multi Volt Cordless Driver Drill -fig2

HiKOKI DS36DA Multi Volt Cordless Driver Drill -fig3

HiKOKI DS36DA Multi Volt Cordless Driver Drill -fig4

HiKOKI DS36DA Multi Volt Cordless Driver Drill -fig5

GENERAL POWER TOOL SAFETY WARNINGS

WARNING
Read all safety warnings, instructions, illustrations and speciﬁcations provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, ﬁ re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the presence of ﬂammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodiﬁed plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
Personal safety
a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the oﬀ -position before connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your ﬁnger on the switch or energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jeweler. Keep your hair and clothing away from moving parts.
Loose clothes, jeweler or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and oﬀ . Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may aﬀect the power tools operation. If damaged, have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
Use of the power tool for operations diﬀerent from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
Battery tool use and care
a) Recharge only with the charger speciﬁed by the manufacturer.
A charger that is suitable for one type of battery pack may create a risk of ﬁ re when used with another battery pack.
b) Use power tools only with speciﬁcally designated battery packs.
Use of any other battery packs may create a risk of injury and ﬁre.
c) When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a ﬁ re.
d) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, ﬂ ush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
e) Do not use a battery pack or tool that is damaged or modiﬁed.
Damaged or modiﬁed batteries may exhibit unpredictable behavior’s resulting in ﬁ re, explosion or risk of injury.
f) Do not expose a battery pack or tool to ﬁre or excessive temperature.
Exposure to ﬁ re or temperature above 130°C may cause explosion.
g) Follow all charging instructions and do not charge the battery pack or tool outside the temperature range speciﬁed in the instructions. Charging improperly or at temperatures outside the speciﬁed range may damage the battery and increase the risk of ﬁre
Service
a) Have your power tool serviced by a qualiﬁed repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed by the manufacturer or authorized service providers.
PRECAUTION
Keep children and inﬁ rm persons away.
When not in use, tools should be stored out of reach of children and inﬁrm persons.

CORDLESS DRIVER DRILL / COMBI DRILL SAFETY WARNINGS

Safety instructions for all operations

a) Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss. b) Use the auxiliary handle(s). Loss of control can cause personal injury. c) Brace the tool properly before use. This tool produces a high output torque and without properly bracing the tool during operation, loss of control may occur resulting in personal injury. d) Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. Safety instructions when using long drill bits a) Never operate at higher speed than the maximum speed rating of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury. b) Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting in personal injury. c) Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

ADDITIONAL SAFETY WARNINGS

Make sure that the area to be drilled is absolutely free of any hidden obstructions including electrical wiring, water, or gas pipes. Drilling into the aforementioned may result in electric shock or short circuit, gas leak or other hazards that can cause serious accidents or injuries.
Make sure to securely hold the tool during operation. Failure to do so can result in accidents or injuries (Fig. 19).
When using the tool, make sure the side handle is attached and ﬁrmly secured.
If not ﬁrmly secured, the tool may jerk out of position when overburdened, resulting in injury.
During operation, make sure to ﬁrmly hold the tool’s handle and side handle with both hands. Failure to do so may result in injury.
Secure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.
Setting up and checking the work environment. Check if the work environment is suitable by following the precaution.
Do not allow foreign matter to enter the hole for connecting the rechargeable battery.
Never disassemble the rechargeable battery and charger.
Never short-circuit the rechargeable battery.
Short-circuiting the battery will cause a great electric current and overheat. It results in burn or damage to the battery.
Do not dispose of the battery in ﬁ re. If the battery is burnt, it may explode.
Bring the battery to the shop from which it was purchased as soon as the post-charging battery life becomes too short for practical use. Do not dispose of the exhausted
battery.
Do not insert object into the air ventilation slots of the charger. Inserting metal objects or inﬂammables into the charger air ventilation slots will result in electrical shock hazard or damaged charger.
When mounting a bit into the keyless chuck, tighten the sleeve adequately. If the sleeve is not tight, the bit may slip or fall out, causing injury.
When changing the rotational speed with the shift knob, conﬁrm that the switch is oﬀ . Changing the speed while the motor is rotating will damage the gears.
The clutch dial cannot be set between the numerals “1, 4, 7 … 22” or the dots, and do not use with the clutch dial numeral between “22” and the line at the middle of
the drill mark. Doing so may cause damage.
Always use this unit with clockwise rotation, when using it as impact drill.
Resting the unit after continuous work.
The power tool is equipped with a temperature protection circuit to protect the motor. Continuous work may cause the temperature of the unit to rise, activating
the temperature protection circuit and automatically stopping operation. If this happens, allow the power tool to cool before resuming use.
The motor may stop in the event the tool is overloaded. In this should occur, release the tool’s switch and eliminate the cause of the overload. Avoid touching the front case which can heat up during continuous operation.
The motor rotation may be locked to cease while the unit is used as drill. While operating the driver drill, take care not to lock the motor.
The use of the battery in a cold condition (below 0 degree Centigrade) can sometimes result in the weakened tightening torque and reduced amount of work. This, however, is a temporary phenomenon, and returns to normal when the battery warms up.
Install securely the hook. Unless the hook is securely installed, it may cause an injury while using. When electing to carry the tool hooked to your hip belt, make sure to detach the tool bit and side handle. Failure to do so may result in unexpected injury.
Do not look directly into the light. Such actions could result in eye injury.
Wipe oﬀ any dirt or grime attached to the lens of the LED light with a soft cloth, being careful not to scratch the lens.
Scratches on the lens of the LED light can result in decreased brightness.
Do not use the product if the tool or the battery terminals (battery mount) are deformed.
Installing the battery could cause a short circuit that could result in smoke emission or ignition.
Keep the tool’s terminals (battery mount) free of swarf and dust.
○ Prior to use, make sure that swarf and dust have not collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool from falling on the battery.
○ When suspending operation or after use, do not leave the tool in an area where it may be exposed to falling swarf or dust.
Doing so could cause a short circuit that could result in smoke emission or ignition.
Always use the tool and battery at temperatures between -5°C and 40°C.
Always charge the battery at an ambient temperature of 0–40°C.

To extend the lifetime, the lithium-ion battery equips with the protection function to stop the output.
In the cases of 1 to 3 described below, when using this product, even if you are pulling the switch, the motor may stop. This is not the trouble but the result of protection function.

When the battery power remaining runs out, the motor stops.
In such a case, charge it up immediately.
If the tool is overloaded, the motor may stop. In this case, release the switch of tool and eliminate causes of overloading. After that, you can use it again.
If the battery is overheated under overload work, the battery power may stop.
In this case, stop using the battery and let the battery cool. After that, you can use it again.
Furthermore, please heed the following warning and caution.

WARNING

In order to prevent any battery leakage, heat generation, smoke emission, explosion and ignition beforehand, please be sure to heed the following precautions.

Make sure that swarf and dust do not collect on the battery.
○ During work make sure that swarf and dust do not fall on the battery.
○ Make sure that any swarf and dust falling on the power tool during work do not collect on the battery.
○ Do not store an unused battery in a location exposed to swarf and dust.
○ Before storing a battery, remove any swarf and dust that may adhere to it and do not store it together with metal parts (screws, nails, etc.).
Do not pierce battery with a sharp object such as a nail, strike with a hammer, step on, throw or subject the battery to severe physical shock.
Do not use an apparently damaged or deformed battery.
Do not use the battery in reverse polarity.
Do not connect directly to an electrical outlets or car cigarette lighter sockets.
Do not use the battery for a purpose other than those speciﬁed.
If the battery charging fails to complete even when a speciﬁed recharging time has elapsed, immediately stop further recharging.
Do not put or subject the battery to high temperatures or high pressure such as into a microwave oven, dryer, or high pressure container.
Keep away from ﬁ re immediately when leakage or foul odor are detected.
Do not use in a location where strong static electricity generates.
If there is battery leakage, foul odor, heat generated, discolored or deformed, or in any way appears abnormal during use, recharging or storage, immediately remove it
from the equipment or battery charger, and stop use.
Do not immerse the battery or allow any ﬂuids to ﬂow inside. Conductive liquid ingress, such as water, can cause damage resulting in ﬁ re or explosion. Store your battery in a cool, dry place, away from combustible and ﬂammable items. Corrosive gas atmospheres must be avoided.

CAUTION

If liquid leaking from the battery gets into your eyes, do not rub your eyes and wash them well with fresh clean water such as tap water and contact a doctor immediately.
If left untreated, the liquid may cause eye-problems.
If liquid leaks onto your skin or clothes, wash well with clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
If you ﬁnd rust, foul odor, overheating, discolor, deformation, and/or other irregularities when using the battery for the ﬁrst time, do not use and return it to your supplier or vendor.

WARNING
If a conductive foreign matter enters in the terminal of lithium ion battery, the battery may be shorted, causing ﬁre. When storing the lithium ion battery, obey surely the rules of following contents.
○ Do not place conductive debris, nail and wires such as iron wire and copper wire in the storage case.
○ To prevent shorting from occurring, load the battery in the tool or insert securely the battery cover for storing until the ventilator is not seen.

REGARDING LITHIUM-ION BATTERY TRANSPORTATION

When transporting a lithium-ion battery, please observe the following precautions.
WARNING
Notify the transporting company that a package contains a lithium-ion battery, inform the company of its power output and follow the instructions of the transportation company when arranging transport.
○ Lithium-ion batteries that exceed a power output of 100 Whare considered to be in the freight classiﬁcation of Dangerous Goods and will require special application
procedures.
○ For transportation abroad, you must comply with international law and the rules and regulations of the destination country.

HiKOKI DS36DA Multi Volt Cordless Driver Drill -fig6

NAMES OF PARTS (Fig. 1–Fig. 17)

1	Shift knob	16	Housing
2	Rubber cap	17	Latch
3	Front case	18	Charge indicator lamp
4	Clutch dial	19	Protruding portion of the side handle
5	Sleeve	20	Drill mark
6	Trigger switch	21	Triangle mark
7	LED light	22	Hammer mark
8	Battery	23	Screw
9	Hook	24	Groove
10	Strap	25	Remaining battery indicator switch
11	Handle	26	Remaining battery indicator lamp
12	Push button	27	Display panel
13	Side handle	28	Rubber cover
14	Ventilation holes	29	USB port
15	Motor	30	USB cable

USB DEVICE CONNECTION PRECAUTIONS (UC18YSL3)

When an unexpected problem occurs, the data in a USB device connected to this product may be corrupted or lost. Always make sure to back up any data contained in the USB device prior to use with this product. Please be aware that our company accepts absolutely no responsibility for any data stored in a USB device that is corrupted or lost, nor for any damage that may occur to a connected device

WARNING

Prior to use, check the connecting USB cable for any defect or damage.
Using a defective or damaged USB cable can cause smoke emission or ignition.
When the product is not being used, cover the USB port with the rubber cover.
Buildup of dust etc. in the USB port can cause smoke emission or ignition.

NOTE

There may be an occasional pause during USB recharging.
When a USB device is not being charged, remove the USB device from the charger.
Failure to do so may not only reduce the battery life of a USB device, but may also result in unexpected accidents.
It may not be possible to charge some USB devices, depending on the type of device.

SYMBOLS

WARNING
The following show symbols used for the machine. Be sure that you understand their meaning before use.

| **** DS36DA: Cordless Driver Drill DV36DA: Cordless Combi Drill
---|---

| To reduce the risk of injury, user must read instruction manual.

| Only for EU countries
Do not dispose of electric tools together with household waste material!
In observance of European Directive 2012/19/EU on waste electrical and electronic equipment and its implementation in accordance with national law, electric tools that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

| Machine screw
---|---
| Wood screw
| Drill chuck capacity

| Weight* (According to EPTA-Procedure 01/2014)

| Drilling

| Impact drilling

| Switching ON

| Switching OFF

| Disconnect the battery

| Change rotation speed – High speed

| Change rotation speed – Low speed

| Clockwise rotation

| Counterclockwise rotation

| Lights ;
The battery remaining power is over 75%.

| Lights ;
The battery remaining power is 50%–75%.

| Lights ;
The battery remaining power is 25%–50%.

| Lights ;
The battery remaining power is less than 25%.

| Blinks ;
The battery remaining power is nearly empty. Recharge the battery soonest possible.

| Blinks ;
Output suspended due to high temperature. Remove the battery from the tool and allow it to fully cool down.

| Blinks ;
Output suspended due to failure or malfunction. The problem may be the battery so please contact your dealer.

| Warning

Depending on attached battery. The heaviest weight is measured with BSL36B18 (sold separately).

STANDARD ACCESSORIES

In addition to the main unit (1 unit), the package contains the accessories listed on page 252.
Standard accessories are subject to change without notice.

APPLICATIONS

Driving and removing of machine screws, wood screws, tapping screws, etc.
Drilling of various metals
Drilling of various woods
Drilling of brick and concrete block, etc.
Driving and removing of machine screws, wood screws, tapping screws, etc.
Drilling of various metals
Drilling of various woods

SPECIFICATIONS

The speciﬁcations of this machine are listed in the Table on page 251.

Existing batteries (BSL3660/3620/3626, BSL18xx and BSL14xx series) cannot be used with this tool.
NOTE
Due to HiKOKI’s continuing program of research and development, the speciﬁcations herein are subject to change without prior notice.

CHARGING

Before using the power tool, charge the battery as follows.

Connect the charger’s power cord to the receptacle. When connecting the plug of the charger to a receptacle, the charge indicator lamp will blink in red (At 1- second intervals).
Insert the battery into the charger.
Firmly insert the battery into the charger as shown in Fig. 3 (on page 2).
Charging
When inserting a battery in the charger, the charge indicator lamp will blink in blue.
When the battery becomes fully recharged, the charge indicator lamp will light up in green. (See Table 1)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as shown in Table 1, according to the condition of the charger or the rechargeable battery.

Table 1

HiKOKI -icon24

(2) Regarding the temperatures and charging time of the rechargeable battery The temperatures and charging time will become as shown in Table 2.

Table 2

Charger	UC18YSL3

Battery

min

| BSL1415S : 15

BSL1415 : 15

BSL1415X : 15

BSL1420 : 20

BSL1425 : 25

BSL1430C : 30

| ****

BSL1430 : 20

BSL1440 : 26

BSL1450 : 32

BSL1460 : 38

| BSL1815S : 15

BSL1815 : 15

BSL1815X : 15

BSL1820 : 20

BSL1825 : 25

BSL1830C : 30

| ****

BSL1830 : 20

BSL1840 : 26

BSL1850 : 32

BSL1860 : 38

| ****

BSL36A18 : 32

BSL36B18 : 52

USB| Charging voltage| V| 5
Charging current| A| 2

NOTE
The recharging time may vary according to the ambient temperature and power source voltage.
4. Disconnect the charger’s power cord from the receptacle.
5. Hold the charger ﬁrmly and pull out the battery.
NOTE
Be sure to pull out the battery from the charger after use, and then keep it.
Regarding electric discharge in case of new batteries, etc.
As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when
using them the ﬁrst and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2–3 times.

How to make the batteries perform longer.

Recharge the batteries before they become completely exhausted.
When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.
Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.

CAUTION

If the battery is charged while it is heated because it has been left for a long time in a location subject to direct sunlight or because the battery has just been used, the charge indicator lamp of the charger lights for 0.3 seconds, does not light for 0.3 seconds (oﬀ for 0.3 seconds). In such a case, ﬁrst let the battery cool, then start charging.
When the charge indicator lamp ﬂickers (at 0.2-second intervals), check for and take out any foreign objects in the charger’s battery connector. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your authorized Service Center.
Since the built-in micro computer takes about 3 seconds to conﬁrm that the battery being charged with UC18YSL3 is taken out, wait for a minimum of 3 seconds
before reinserting it to continue charging. If the battery is reinserted within 3 seconds, the battery may not be properly charged.

MOUNTING AND OPERATION

Action	Figure	Page
Removing and inserting the battery	2	2
Charging	3	2
Installing / Removing the side handle	4	2
Tightening torque adjustment	5	3
Selecting the drill position	6	3
Selecting the impact position	7	3
Change rotation speed	8	3
Removing and mounting the hook	9	3
Remaining battery indicator	10	4
How to use the LED light	11	4
Mounting the bit	12	4
Reversing the rotational direction	13	4
Switch operation	14	4
Charging a USB device from a electrical outlet	15-a	5
Charging a USB device and battery from a electrical outlet	15-b	5
How to recharge USB device	16	5
When charging of USB device is completed	17	5
Selecting accessories	―	253

REACTIVE FORCE CONTROL

This product features a reactive force control (RFC) to minimize the danger of twisting the operator’s arms when tool itself suddenly jerks during operation.
When the tool bit is suddenly overburdened, the tool itself may react to the motor’s force and twist in the opposite direction of the motor’s rotation, which could result in injury. (Fig. 19)
When the tool’s built-in control detects a reactive force, it stops the motor’s output before the entire tool jerks to lessen the twisting of the operator’s arms.
When this function activates, it will be indicated by the LED light blinking (0.1-second blinks/oﬀ 0.5 seconds) while the switch is pulled. (See “LED light warning signals”)
However, as the function may not activate depending on situations or conditions during operation, so care should be taken to avoid any sudden overburdening of the tool bit
when operating the tool.

Possible causes of sudden overburdening
1 Tool bit biting into material
2 Impact against nails, metal or other hard objects
3 Tasks involving prying or any excess application of pressure, etc.
Also, other causes include any combination of the aforementioned.
When the reactive force control (RFC) is triggered When the RFC is triggered and the motor stops, turn oﬀ the tool’s switch and remove the cause of the overburdening before continuing operation.

LED LIGHT WARNING SIGNALS (Fig. 20)

This product features functions that are designed to protect the tool itself as well as the battery. While the switch is pulled, if any of the safeguard functions are triggered
during operation, the LED light will blink as described in Table 3. When any of the safeguard functions are triggered, immediately remove your ﬁnger from the switch and follow the instructions described under corrective action.

HiKOKI DS36DA Multi Volt Cordless Driver Drill -fig8

Table 3

Safeguard Function	LED Light Display	Corrective Action
**** Overburden Protection	******** On 0.1 second/oﬀ 0.1 second
	If the operating with the shift knob set on HIGH, adjust to LOW and

continue operation. Remove the cause of the overburdening.
**** Reactive Force Control| Remove the cause of the overburdening. When operating the tool, firmly hold the tool to make sure it doesn’t jerk.
Temperature Protection| On 0.5 second/oﬀ 0.5 second
| Allow the tool and battery to thoroughly cool.

MAINTENANCE AND INSPECTION

Inspecting the tool
Since use of as dull tool will degrade eﬃciency and cause possible motor malfunction, sharpen or replace the tool as soon as abrasion is noted.
Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that they are properly tightened. Should any of the screws be loose, retighten them immediately. Failure to do so could
result in serious hazard.
Maintenance of the motor
The motor unit winding is the very “heart” of the power tool. Exercise due care to ensure the winding does not become damaged and/or wet with oil or water.
Inspection of terminals (tool and battery)
Check to make sure that swarf and dust have not collected on the terminals.
On occasion check prior, during and after operation.
CAUTION
Remove any swarf or dust which may have collected on the terminals.
Failure to do so may result in malfunction.
Cleaning on the outside
When the power tool is stained, wipe with a soft dry cloth or a cloth moistened with soapy water. Do not use chloric solvents, gasoline or paint thinner, for they melt plastics.
Storage
Store the power tool and battery in a place in which the temperature is less than 40°C and out of reach of children.

NOTE
Storing lithium-ion batteries.
Make sure the lithium-ion batteries have been fully charged before storing them.
Prolonged storage (3 months or more) of batteries with a low charge may result in performance deterio
However, signiﬁcantly reduced battery usage time may be recovered by repeatedly charging and using the batteries two to ﬁve times.
If the battery usage time is extremely short despite repeated charging and use, consider the batteries dead and purchase new batteries.

CAUTION
In the operation and maintenance of power tools, the safety regulations and standards prescribed in each country must be observed.

Important notice on the batteries for the HiKOKI cordless power tools
Please always use one of our designated genuine batteries. We cannot guarantee the safety and performance of our cordless power tool when used with batteries other than these designated by us, or when the battery is disassembled and modiﬁed (such as disassembly and replacement of cells or other internal parts).

GUARANTEE
We guarantee HiKOKI Power Tools in accordance with statutory/ country speciﬁc regulation. This guarantee does not cover defects or damage due to misuse, abuse, or normal wear and tear. In case of complaint, please send the Power Tool, dismantled, with the GUARANTEE CERTIFICATE found at the end of this Handling instruction, to a HiKOKI Authorized Service Center.

Information concerning airborne noise and vibration
The measured values were determined according to EN62841 and declared in accordance with ISO 4871.

Measured A-weighted sound power level:
91 dB (A) (DS36DA)
100.5 dB (A) (DV36DA)
Measured A-weighted sound pressure level:
80 dB (A) (DS36DA)
89.5 dB (A) (DV36DA)
Uncertainty K: 5 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined according to EN62841.
Drilling into metal:
Vibration emission value ah, D < 2.5 m/s2
(DS36DA, DV36DA)
Uncertainty K = 1.5 m/s2 (DS36DA, DV36DA)
Impact drilling into concrete:
Vibration emission value ah, ID = 10.3 m/s2 (DV36DA)
Uncertainty K = 1.5 m/s2 (DV36DA)

The declared vibration total value and the declared noise emission value have been measured in accordance with a standard test method and may be used for comparing one
tool with another.
They may also be used in a preliminary assessment of exposure.
WARNING

The vibration and noise emission during actual use of the power tool can diﬀ er from the declared total value depending on the ways in which the tool is used especially what kind of workpiece is processed; and
Identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched oﬀ and when it is running idle in addition to the trigger time).
NOTE
Due to HiKOKI’s continuing program of research and development, the speciﬁcations herein are subject to change without prior notice.

TROUBLESHOOTING

Use the inspections in the table below if the tool does not operate normally. If this does not remedy the problem, consult your dealer or the HiKOKI Authorized Service Center.
1. Power tool

Symptom	Possible cause	Remedy
Tool doesn’t run	No remaining battery power	Charge the battery.
Battery isn’t securely attached.	Push in the battery until a click is heard.
Tool suddenly stopped	Tool was overburdened	Remove the cause of the

overburdening. See “Reactive force control”.
Reactive force control was activated
Battery or tool overheated| Allow the tool and battery to thoroughly cool.
Tool bits

-can’t be attached

-fall oﬀ

| The shape of the attachment portion doesn’t match| The chucking diameter of the keyless chuck is 1.5 mm to 13 mm. Use a bit that falls within the stated range.
The lock of the keyless chuck is worn| Contact a HiKOKI Authorized Service Center and arrange to have the old keyless chuck replaced with a new one.
Switch can’t be pulled| Forward/reverse selector button is positioned halfway| Press the button firmly into position for the desired direction of rotation.
Screw head slips or comes loose.| Bit number doesn’t match with the screw size| Install a suitable bit.
The bit is worn| Replace with a new bit.
Holes can’t be smoothly drilled.| The drill is worn| Replace with a new drill.
Rotation speed isn’t appropriate| Adjust the rotation speed (HIGH/LOW) to match the material to be drilled.
The drill is rotating in reverse| Switch to forward rotation.
Battery cannot be installed| Attempting to install a battery other than that specified for the tool.| Please install a multi volt type battery.

2. Charger

Symptom	Possible cause	Remedy

The charge indicator lamp rapidly flickers purple, and battery charging doesn’t begin.| The battery is not inserted all the way.| Insert the battery firmly.
There is foreign matter in the battery terminal or where the battery is attached.| Remove the foreign matter.
The charge indicator lamp blinks red, and battery charging doesn’t begin.| The battery is not inserted all the way.| Insert the battery firmly.
The battery is overheated.| If left alone, the battery will automatically begin charging if its temperature decreases, but this may reduce battery life. It is recommended that the battery be cooled in a well-ventilated location away from direct sunlight before charging it.
Battery usage time is short even though the battery is fully charged.| The battery’s life is depleted.| Replace the battery with a new one.
The battery takes a long time to charge.| The temperature of the battery, the charger, or the surrounding environment is extremely low.| Charge the battery indoors or in another warmer environment.
The charger’s vents are blocked, causing its internal components to overheat.| Avoid blocking the vents.
The cooling fan is not running.| Contact a HiKOKI Authorized Service Center for repairs.
The USB power lamp has switched oﬀ and the USB device has stopped charging.| The battery’s capacity has become low.| Replace the battery with one that has capacity remaining.
Plug the charger’s power plug into an electric socket.
USB power lamp does not switch oﬀ even though the USB device has finished charging.| The USB power lamp lights up green to indicate that USB charging is possible.| This is not a malfunction.
It is unclear what the charging status of a USB device is, or whether its charging is complete.| The USB power lamp does not switch oﬀ even when charging is complete.| Examine the USB device that is charging to confirm its charging status.
Charging of a USB device pauses midway.| The charger was plugged into an electrical socket while the USB device was being charged using the battery as the power source.| This is not a malfunction.
The charger pauses USB charging for about 5 seconds when it is diﬀerentiating between power sources.
A battery was inserted into the charger while the USB device was being charged using a power socket as the power source.
Charging of the USB device pauses midway when the battery and the USB device are being charged at the same time.| The battery has become fully charged.| This is not a malfunction.
The charger pauses USB charging for about 5 seconds while it checks whether the battery has successfully completed charging.
Charging of the USB device doesn’t start when the battery and the USB device are being charged at the same time.| The remaining battery capacity is extremely low.| This is not a malfunction.
When the battery capacity reaches a certain level, USB charging automatically begins.
| DS36DA| DV36DA
---|---|---
V| V| 36| 36
n0| Ls| min-1| 0–500| 0–500
Hs| min-1| 0–2100| 0–2100

Bpm

| Ls| min-1| ―| 0–7500
Hs| min-1| ―| 0–31500
| mm| ―| 20
| mm| 102| 102
| mm| 16| 16
| mm| 6| 6
| mm| 12| 12
| mm| 1,5–13| 1,5–13
| kg| 2,7–3,0| 2,7–3,0
| DS36DA, DV36DA
---|---
(2XCP)| (2XCK)| (NNP)| (NN)
| 1| 1| 1| 1
| 1| 1| ―| ―
| 2| 2| ―| ―
| 1| 1| ―| ―
| 1| ―| 1| ―
| ―| 1| ―| ―
| 1| 1| 1| 1

HiKOKI DS36DA Multi Volt Cordless Driver Drill -fig9

GUARANTEE CERTIFICATE

Model No.
Serial No.
Date of Purchase
Customer Name and Address
Dealer Name and Address
(Please stamp dealer name and address)

Hikoki Power Tools (U.K.) Ltd.
Precedent Drive, Rooksley, Milton Keynes, MK 13, 8PJ,
United Kingdom
Tel: +44 1908 660663
Fax: +44 1908 606642
URL: http://www.hikoki-powertools.uk

EC DECLARATION OF CONFORMITY
We declare under our sole responsibility that Cordless Driver Drill / Cordless Combi Drill, identic ed by type and speciﬁc identic cation code
1), is in conformity with all relevant requirements of the directives 2) and standards 3). Technical ﬁ le at 4) – See below. The European Standard Manager at the representative oﬃce in Europe is authorized to compile the technical ﬁ le. The declaration is applicable to the product aﬃxed CE marking

1) DS36DA
DV36DA
C355240S
C355248S
2) 2006/42/EC, 2014/30/EU, 2014/35/EU, 2011/65/EU
*3) EN62841-1:2015
EN62841-2-1:2018
EN60335-1:2012+A11:2014
EN60335-2-29:2004+A2:2010
EN55014-1:2006+A1:2009+A2:2011
EN55014-2:1997+A1:2001+A2:2008

*4) Representative oﬃ ce in Europe
Hikoki Power Tools Deutschland GmbH
Siemensring 34, 47877 Willich, Germany
Head oﬃ ce in Japan
Koki Holdings Co., Ltd.
Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo, Japan
30. 6. 2021
Akihisa Yhagi
European Standard Manager
**** 30. 6. 2021

A. Nakagawa
Corporate Oﬃcer

Koki Holdings Co., Ltd.
106 Code No. 099723175 G
Printed in China