StarTech RKCONS1701 1-Port VGA Rackmount LCD Console User Guide

: June 6, 2024
: StarTech

Table of Contents

Product Design
Package Contents
Requirements
Installation
Installation Depth
Connect the Console
Operation
Safety Measures
FCC Compliance Statement
Industry Canada Statement
Warranty Information
Limitation of Liability
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Quick-Start Guide
SKU #: RKCONS1701

1-Port VGA Rackmount LCD Console |17 in | 1U

Product Design

The actual product may vary from photos

Front View

1 Handle
2 Rails
3 Mounting Brackets (Installed)| 4 Keyboard LEDs
5 Display Menu Buttons
6 Release Switch
---|---

Rear View

1 Power Connection Port
2 Power Switch| 3 Ground Connection Screw
4 Host Port
---|---

Package Contents

LCD Rack Console x 1
KVM Cables x 1
M5 Cage Nuts x 8
M5 Screws x 8
Regional Power Cords (NA, JP, EU, UK, ANZ) x 5
Mounting rails x 2
Quick-Start Guide x 1

Requirements

1U of Rack Space
Grounding Wire
Power Source
Computer, Server, or KVM
Phillips Type Screwdriver

Requirements are subject to change. For the latest requirements, please visit www.startech.com/RKONS1701.

Installation

Caution! Double pole / neutral fuse. Disconnect mains before
Always ground the unit before connecting/disconnecting the Power Cord.

Mounting the LCD Rackmount Console

Note: It’s easier to install the LCD Rackmount Console if another person helps you with the installation.

Warning: Use caution and proper lifting techniques when installing the LCD Rackmount Console.

Based on the mounting depth of the server rack that you are using, select the appropriate length of Mounting Rails.
Decide where in the server rack you want to install the LCD Rackmount Console.
Insert the MS Cage Nuts (two per Mounting Post) into the square Mounting Holes on the Mounting Posts.
Align the rear Mounting Bracket Rails with the MS Cage Nuts on the corresponding Mounting Post.
Insert an MS Screw (two per Mounting Post) through the rear Mounting Bracket Rail and into the MS Cage Nut. Do not tighten the MS Screws.
With assistance, slide the LCD Rackmount Console into the server rack guiding the rear Mounting Bracket Rails into the Rail Assembly.
Insert an MS Screw (two per Mounting Post) through the front Mounting Bracket Rail into the MS Cage Nut.
Use a Phillips Type Screwdriver to tighten the MS Screws.
Ensure that the rear Rails are properly aligned.
Use a Phillips Type Screwdriver to tighten the MS Screws. Grounding the LCD Console

Notes: Grounding wires are typically green or green with a yellow stripe, and should be at least 18 AWG.

Grounding is recommended in all environments and essential in environments with high levels of electromagnetic interference (EMI), or frequent electrical surges.

Using a Phillips Head Screwdriver, loosen the Grounding Connection Screw.
Attach the Grounding Wire to the shaft of the Grounding Connection Screw.
Tighten the Grounding Connection Screw, making sure not to over-tighten.
Attach the other end of the Grounding Wire (not connected to the LCD Rackmount Console) to a proper earth-ground

Installation Depth

Connect the Console

Important Considerations

If you’re installing the device in a closed or multi-unit rack assembly, ensure that the environmental conditions are within the unit’s maximum and minimum specifications.
Installing this unit in a rack or cabinet may reduce airflow. Consider your airflow requirement when selecting a location for
The device should be installed with an even mechanical load.
It’s recommended that the device be connected to a power source with overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this concern.
The device should be grounded appropriately.

Connect a Grounding Wire to the Ground Connection Screw on the LCD Rackmount Console and to the earth-ground
Connect the KVM Cable to a Computer, Server or KVM and to the host ports on the console.
Connect the appropriate Power Cord for your region to the Power Connection Port on the LCD Rackmount Console and to a Power Source.
Use the Power Switch to turn on the LCD Rackmount Console.
Open the LCD Rackmount Console. For more information about how to do this, see the “Open the console” topic.
Turn on the connected Computer, Server or

Disconnect the Console

Power off the connected Computer, Server or
Close the LCD Rackmount Console. For more information about how to do this, see the “Close the console” section.
Use the Power Switch to turn off the LCD Rackmount Console.
Disconnect the Power Cord from the Power Connection Port on the LCD Rackmount Console.

Note: Always disconnect the Power Cord before disconnecting the Grounding Wire.

Disconnect the KVM Cable connected to a Computer, Server or
(Optional) Disconnect the Grounding Wire connected to the Ground Connection Screw on the LCD Rackmount Console.

Operation

Open the Console

Move the Release Switch to the unlocked position.
Use the Handle to pull the LCD Rackmount Console out towards you until you hear the LCD Rackmount Console click into place.
Pull the Display up and position it at the desired angle.

Close the Console

Lower the display until it’s flush against the
Slide the switches located on the sides of the console forward and push the LCD Rackmount Console in towards the rear of the rack.
Release the switches and continue pushing the LCD Rackmount Console the rest of the way into the rack.

Safety Measures

Wiring terminations should not be made with the product and/or electric lines under power.
Product installation and/or mounting should be completed by a certified professional.
Please note that the included power cables are for use with this product only and cannot be used with other electrical devices.

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.
CAN ICES-3 (B)/NMB-3(B)
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com.
Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.

Warranty Information

This product is backed by a two-year warranty. StarTech.com warrants its products against defects in materials and workmanship for the periods noted, following the initial date of purchase. During this period, the products may be returned for repair or replacement with equivalent products at our discretion. The warranty covers parts and labor costs only. StarTech.com does not warrant its products from defects or damages arising from misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees, or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.

StarTech.com Ltd.
45 Artisans Crescent
London, Ontario
N5V 5E9
CanadaFR: startech.com/fr
DE: startech.com/de
ES: startech.com/es
NL: startech.com/nl
IT: startech.com/it
JP: startech.com/jp| StarTech.com LLP
4490 South Hamilton
Road
Groveport, Ohio
43125
The U.S.A.| StarTech.com Ltd.
Unit B, Pinnacle 15
Gowerton Road
Brackmills,
Northampton
NN4 7BW
United Kingdom| StarTech.com Ltd.
Siriusdreef 17-27
2132 WT
Hoofddorp
The Netherlands
---|---|---|---