truelife AquaFloss Lite Effective Interdental Cleaning Instruction Manual
- June 6, 2024
- truelife
Table of Contents
truelife AquaFloss Lite Effective Interdental Cleaning
Box contents:
- TrueLife AquaFloss Lite
- 2× Standard nozzle heads
- USB charging cable
- Manual and safety instructions
Product description:
- Nozzle head
- Decorative ring
- On/Off button
- Mode change button
- Mode indicator
- Charging indicator
- Handle
- Water tank
- Button to release nozzle head
- Charging socket
- Water tank cap
Warning: There may be residual water in the device. This is distilled water used during quality control testing.
Directions for use:
Before the first use, remove all packaging material. If the water flosser has been stored in a low-temperature environment during transport, leave it at room temperature for at least two hours before use.
- Attach the head to the water flosser. You will hear a clicking sound when it is correctly attached.
- Remove the water tank cap and fill the tank with water; the temperature of the water should not exceed 40 °C. The capacity of the water tank is 200 ml. Then replace the cap, ensuring that water does not spill.
- Press the „mode change“ button and select the desired flossing mode. You can also change the mode while flossing. You can choose between 3 modes:
- “Daily” mode – suitable for regular everyday flossing
- “High” – suitable for deep cleaning of teeth
- “Pulse” mode – suitable for gently massaging teeth and gums
- Leave your mouth slightly open to allow water to rinse from your mouth into the sink. Press the On / Off button to start the flosser. Direct the water jet at a 90 ° angle to the teeth and gums. Slowly run the stream of water around your teeth. Direct the stream of water onto the gums and into the space between the teeth. If you have braces, you can direct the water between the joints of the braces.
- When you have finished flossing, switch off the device using the On / Off button. Open the water tank cap and pour out any remaining water. Switch the device on again with the On / Off button to drain the water from the pump. Press the On / Off button to turn off the device and close the water tank cap.
Warning: To prevent the build-up of bacteria, ensure that no water remains in the device. If you do not intend to use the device for a longer time, make sure that it is thoroughly dried before storing it.
Charging:
The water flosser is not supplied with a fully charged battery. Before using
for the first time, fully charge the water flosser.
Plug one end of the USB cable into the charging socket at the rear of the
water flosser. Plug the other end of the USB cable into an adapter (adapter
not included). Insert the adapter into the plug socket. During charging, the
charging indicator will light up red. When fully charged, the charge indicator
will change to green. It takes approximately 6 hours to fully charge the water
flosser.
Warning: If the charging indicator flashes red during or after use, this
indicates that the battery is low.
Warning: To ensure maximum battery life, we recommend charging the water
flosser once a week.
Inserting and replace the nozzle head
Insert the nozzle head into the hole at the top of the water flosser. You will
hear a click when the nozzle head has been correctly attached.
To remove the nozzle head from the main body, press and hold the release
button and then detach the nozzle head from the water flosser.
The nozzle head rotates 360 °.
Warning: Only insert and remove the nozzle head when the water flosser is
switched off.
Warning: Nozzle heads are items of personal hygiene and are not covered
by warranty.
Maintenance:
Use only water and neutral detergents to clean the device. Never use caustic or abrasive clea-ners as they may damage the device. Do not use water whose temperature exceeds 50 ° C. Keep the device away from high temperatures and avoid direct sunlight.
-
The device
Remove dirt by wiping with a towel or cloth with liquid soap and water, then ensure all water is rinsed off and wipe dry. Do not immerse the device in water.
Warning: Water must not enter the USB socket. -
Water tank
Wash the tank with water and wipe with a dry cloth. Dry the tank thoroughly if you do not intend to use it for a longer time.
Warning: For greater ease of cleaning, the water tank can be removed from the body of the water flosser. -
Nozzle head
Wash the nozzle head with water and wipe with a cloth. Replace the nozzle head regularly, at least once every three months, or more often depending on wear.
Troubleshooting:
| Problem __ | Possible cause | Solution |
|---|
Water pressure is very low
| The nozzle head is unclean / battery is low| Replace the nozzle head with a
new one / recharge the water flosser
No water at all emits from the water flosser| Water tank is empty / The device
is tilted at the wrong angle| Refill the water tank / Move the device to the
correct position (i.e., vertical)
Nozzle head cracks| Nozzle head has been used for too long| Replace the
nozzle head with a new one
Water tank leaks| Water tank cap is damaged| Contact the manufacturer to
replace the water tank
Product liability:
TrueLife products are guaranteed to be free from manufacturing defects. In the
event of such defects, elem6 s.r.o. will repair or replace the defective part
or product with a comparable part or product at its sole discretion. The
warranty will be deemed void if the device is altered or tampered with. The
warranty does not cover damage resulting from use, accident or normal wear and
tear. elem6 s.r.o. assumes no responsibility for any accident, injury, death,
loss, or other claims related to or resulting from the use of this product.
elem6 s.r.o. shall in no event be lia-ble for incidental or consequential
damages in connection with or arising from the use of this product or any of
its components. Return or exchange of spare parts and / or products may be
subject to shipping, handling, and replacement or replenishment fees.
This product should be stored out of the reach of children. Use by children
should take place only under the direct supervision of an adult.
SAFETY ADVICE WHEN OPERATING THE DEVICE:
- Read the enclosed safety instructions carefully.
- The latest version of the manual, including instructions for operating the device, can be downloaded at: www.truelife.eu
- Printing errors reserved.
Manufacturer: elem6 s.r.o., Braškovská 15, 16100 Prague 6, Czech Republic
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>