truelife BELLE IPL E5 Pianless Long Lasting Hair Removal Device User Manual

truelife BELLE IPL E5 Pianless Long Lasting Hair Removal Device

BOX CONTENTS

• TrueLife Belle IPL E5
• HR lamp, AC lamp, SR lamp
• Charging base
• Safety glasses
• Manual

PRODUCT DESCRIPTION

1. Treatment button
2. Cooling mode button
3. Power button
4. Level button
5. LCD display
6. Indicators
7. Replaceable lamp head
8. Treatment window
9. Charging base
10. Base cable input

SAFETY PRECAUTIONS

• To ensure your own safety, do not use the controls on this unit while driving.
• The device must always be used with safety goggles.
• Always keep the device and the adapter dry.
• To reduce the risk of electric shock, do not touch any parts if the unit is broken.
• Do not use the device in a humid environment – for example with running water or a full bath.
• The device may be used by children and persons with reduced physical, sensory or mental capabilities, provided they have been given supervision or instruction concerning use of the device and understand all risks associated with the use of the device.
• The device must not be used by children under 15 years of age. Persons aged 15-18 only under the supervision of a guardian.
• The device is equipped with a transformer and can only be used with the original one supplied.
• Always check the device before use. Do not use the device if any part is damaged.
• If the adapter is damaged, do not use it. There is a risk of electric shock.
• The light emitting treatment lamp/window may be very hot after use. Do not touch the inside of the window immediately after application.
• Before using the device, you should clean the skin and ensure that it is completely hairless, dry and free of greasy substances.
• Make sure that nothing obstructs the flow of air from the vents of the device.
• Never subject the device to shocks, shake it or drop it.
• If you move the device from a very cold environment to a very warm environment or vice versa, wait about 3 to 4 hours before using it.
• Store the device in a dry place where it will not get covered in dust.
• Do not expose the device to direct sunlight or UV radiation, otherwise it may be damaged.− Never leave the device unattended when it is switched on. Always switch off the device after use.
• For hygienic reasons, the device is intended for one user.
• The device is only intended for removing unwanted hair from parts of the body from the face and neck down. Do not use it for any other purpose.
• The device is not washable. Never immerse the device in water or wash it under the tap.
• The device is not intended for children. It is not a toy and children should not use it.
• Do not mark the treated areas with a pencil or pen. It could cause skin burns.
• Use only with settings that are appropriate for your skin type. When used with settings other than those recommended, the risk of skin reactions and side effects may increase.− Never leave the device unattended when it is switched on. Always switch off the device after use.
• Do not use the device if any of the cases listed in the contraindications section apply to you.− Do not treat the same area of skin more than once during one session. This does not increase the effectiveness of the treatment but increases the risk of skin reactions.
• Hair removal using lasers or intense pulsed light sources can cause increased hair growth in some individuals. According to available data, the highest risk of this reaction is in women of Mediterranean, Middle Eastern, and South Asian descent treated on the face and neck.
• The box contains small pieces that can be dangerous for children. Always keep the product out of the reach of children. The bags can cause suffocation if placed on the head and the pieces they contain are a choking hazard.

Contraindications

• Never use the device if you have skin type VI (for type V at your own discretion). In this case, you are at high risk of skin reactions, such as excessive or insufficient pigmentation, significant redness or burns. For a list of skin types, see page 3.
• Never use the device if you are pregnant or breastfeeding. The device has not been tested on pregnant or lactating women.
• Never use the device if you have any active implant, such as a pacemaker, neurostimulator, insulin pump, etc.
• Do not use the device if you are taking any of the following medicines:
  • if your skin has been treated in the last week with alpha-hydroxy acids (AHA), beta hydroxy acids (BHA ), topical isotretinoin, and azelaic acid.
  • if you have taken any form of isotretinoin Accutane or Roaccutane in the last six months. This treatment thins the skin so that it can then be more prone to cracks, injuries and irritation.
  • If you are taking photosensitive products or medicines, check the package leaflet of the medicine and never use the device if the medicine causes photoallergic reactions, photo-toxic reactions or if you should avoid the sun while taking this medicine.
  • if you are taking anticoagulants (including large doses of aspirin).
  • if you are taking analgesics that reduce your skin‘s sensitivity to heat.
  • if you are taking immunosuppressive medicines.
• Never use the device:
  • if you have received radiation therapy or chemotherapy in the last 3 months.
  • if you have undergone surgery in the last three weeks in the areas you want to treat.
• Do not use the device if you have or have had the following illnesses:
  • if you have diabetes or other systemic or metabolic diseases.
  • if you have had heart failure.
  • if you have a light-sensitive disease such as polymorphic light flare (PMLE), solar urticaria, porphyria, etc.
  • if you have had a collagen disorder, including keloid scarring or poor wound healing.
  • if you suffer from light-sensitive epilepsy.
  • if you have light-sensitive skin that easily get a rash or have an allergic reaction.
  • if you have a skin condition, such as active skin cancer, a history of skin cancer, or any other localized outbreak of cancer in the areas you want to treat.
  • if you have a history of a venous disorder, such as varicose veins or spider veins in the areas you want to treat.
  • if you have any bleeding disorder.
  • if you have a history of the immunosuppressive disease (including HIV infection or AIDS).
• Do not use the device:
  • if you have inflammation, eczema, burns, inflamed hair follicles, open wounds, abrasions, herpes simplex virus, injuries or lesions and hematomas in areas you want to treat.
  • If you have irritation (redness or cuts), sunburn, recent sunburn or artificially tanned skin.
• Do not use the device on the following places/areas:
  •  birthmarks, freckles, dilated veins, darker pigmented areas, scars, skin irregularities without consulting a doctor. Application to these areas can lead to burns and skin disco-loration, which could potentially make it more difficult to identify skin diseases.
  •  warts, tattoos or permanent makeup.
  •  around or near the eyes and eyebrows.
  •  on the face, lips, nipples, areolas, small labia, vagina, anus and inside the nose and ears.
  •  men must not use the device on the face and neck, including all areas where beards grow, or the entire genital area.
  •  in areas where you use long-acting deodorants. Skin reactions may occur.
  •  on or near artificial objects, such as silicone implants or piercings.

HOW DOES THE EPILATOR WORK

IPL technology
Epilation is performed using intense pulsed light. The whole process is painless, leaving your skin smooth for up to several months.
Using IPL technology, the epilator emits gentle pulses of light in the wavelength range of 510 to 1100 nm below the surface of the skin. This targets the melanin in the hair follicle and helps break the cycle of hair re-growth. Light pulses create heat that warms the hair follicle, destroying it which leads to the hair falling out.
What can you expect?
After application
You should not see any significant side effects of the treatment immediately after application. During the first weeks of use, hair growth will still be visible. These are probably hairs that were not in their growth phase during application when IPL technology is most effective.
6th to 12th week of use
You should already see a reduction in hair growth. However, many hairs will still not have be treated in their growth phase. It is important to continue weekly treatment.
After 12 weeks of use
Approximately after completing the 12-week plan, you should already notice a significant re-duction in hair in the treated area. The remaining hairs should be finer and lighter. Continued monthly treatment or treatment as needed should keep your skin hair-free.

HOW TO USE THE EPILATOR? Before using for the first time

Recommended skin colour
TrueLife IPL epilators work effectively and safely on different skin tones. In general, IPL epilators are not recommended for dark skin and light hair. To determine if an IPL epilator is right for you, use the Fitzpatrick scale, which distinguishes 6 degrees of skin colour, and determine if an IPL epilator is right for you.

Preparing the skin
Before use, make sure that your skin is in good condition without injury. It must also be shaved, clean and dry (without any residue such as creams, make- up, antiperspirants or deodorants).
Before the first epilation, we recommend performing a patch test on a small area of skin. Per-form the test 24 hours before epilation to check for any side effects.
How to test

1. Choose an area of skin close to the area you want to epilate.
2. Switch on the device and select level 1.
3. Place the device on the skin, press the treatment button and the device will emit a flash. Emit two flashes like this, corresponding to two treatment windows on the surface.
4. Increase the setting by one level and repeat the flashes. Repeat for the other levels until the flashes are uncomfortable. Once you reach a level that is uncomfortable for you, end the test. Use the last level, which is pleasant for you, during the subsequent epilation.
5. After the test, wait 24 hours and check for a skin reaction. If the skin looks normal, you can proceed with the first epilation. A patch test should be performed on all areas you are going to treat.

Preparing the device

1. Remove the device and its accessories from the box.
2. Before starting treatment, make sure that the device is clean, dry and undamaged. You can clean the epilation window.
3. Connect the charging base to an electrical outlet and then the device to the charging base.
4. The device is now ready for use.

Note: Before switching on, make sure that the lamp head is installed correctly.

EPILATION
If the patch test is successful and your skin is prepared, you can start epilating.

1. Press the power button for 3 to 5 seconds to turn on the device.
2. The LED indicator starts flashing blue and white. When the device is ready for use, the indica-tor lights up white only.
3. On the display you can see: the type of lamp, the number of flashes remaining, the light in-tensity level, the cooling mode icon, the auto mode icon and the overheating warning icon.
4. Press the level button to set your desired light level (level 1 lowest, level 5 highest), which you determined during the patch test.
5. When you have everything ready, touch the skin where you want to epilate. As shown in the picture. The indicator lights up blue and the device is ready to emit light.
6. Press the treatment button to emit a flash. The flash should make you feel warm.
7. Place the device on the next area you want to epilate. After each flash, it takes up to 3 seconds for the device to be ready for the next flash. You can emit a flash when the blue indicator lights up again.
8. To ensure complete treatment of all areas, emit flashes close together. Effective light comes only from the light-emitting treatment window, so the treated areas need to overlap. Howe-ver, always be sure to send the flash to the same area only once. Irradiation of the same area does not double the effectiveness of the treatment, but increases the risk of skin reactions.
9. When you have finished epilating, hold down the power button for 3 to 5 seconds and the device will switch off.
10. Disconnect the device from the power supply.

Note: The device may enter overheat protection mode after a long period of operation. The device cannot be used in this mode until its temperature drops. The device can be used again as soon as the overheating warning icon disappears.
Note: If redness or burning occurs for several minutes, soothe the skin by applying a coolant or a cotton pad.
Note: If you notice any discoloration on the skin (such as fading or darkening), stop using the device immediately and undergo a medical examination to determine the cause.
Modes
The device offers two epilation modes for convenience. In addition to the standard single flash mode, it is also possible to use automatic mode.
Standard mode
Standard mode is suitable for treating small and hard-to-reach areas. These include the face, armpits, bikini area, knees, shins and ankles.
Auto mode
Auto mode offers convenient and fast use on larger areas such as feet. Hold down the level button for 3 seconds. The device switches to automatic mode. Move the device slowly and smoothly from the bottom to the top of the epilated area. Make sure that the device is in constant contact with the skin so that it can emit flashes at all times.
Cooling mode
Cooling mode is automatically switched on. During epilation, the skin is cooled at the same time making the treatment less painful. If you want to turn off the automatic cooling when epilating, press the cooling mode button. Pressing the button again to switch it on. The cooling mode can also be used on it own. Press the cooling mode button for 3-5 seconds. You can then place the device on the area and slowly slide it to cool the area. To turn off cooling mode, press the cooling mode button again for 3-5 seconds.
Treatment plan
The hair growth cycle varies from person to person. It ranges around 16 months depending on which part of the body. Due to the fact that only hairs in the growth phase respond to the epila-tion, several treatments are needed to achieve permanently smooth skin. For these reasons, we recommend the following plan.
Initial phase
For the first 4 to 12 weeks, we recommend epilating once a week. If hair growth stops before, it is not necessary to continue treatment until the end of week 12. In this case, you can move on to the next stage.
Maintenance phase
After the initial phase, we recommend treatments every 4 to 8 weeks when you notice hair growth. This phase helps to preserve the results achieved and maintain smooth skin for many months. The time between treatments may vary with regard to individual hair growth and also to each specific area of the body.

Lamp head types
The device can be used with three different lamp heads. Each lamp has a different function.

• HR lamp – The HR lamp is designed for hair removal.
• SR lamp – The SR lamp is designed to rejuvenate the skin.
• AC lamp – The AC lamp is designed to remove acne.

Replacing the lamp head
The device allows you to remove and replace the lamp head. Follow the instructions below.

AFTERCARE

• After epilating, you can safely apply lotion, cream, deodorant, moisturizer or other cosmetic products to the treated area.
• If you experience skin irritation or redness after treatment, wait until these symptoms have disappeared before applying any product to the skin. If you notice skin irritation or redness after applying the product, rinse it with water.
• After epilating, we recommend not exposing the epilated area immediately to sunlight, or to protect it with a product with a protective factor. It is also not advisable to visit tanning booths and solariums within 24 hours after epilation.

DEVICE MAINTENANCE

• Maintaining this device ensures trouble-free operation and reduces the risk of damage.

• Keep the device away from extreme humidity and temperatures and do not expose the device to direct sunlight or ultraviolet light for extended periods of time.

• Never use compressed air, scouring pads, abrasive or aggressive cleaning agents such as petrol or acetone to clean the device.

• Do not expose the device to sudden and extreme changes in temperature. This can cause moisture to condense inside the device, which could damage the device. In the event of moisture condensation, allow the device to dry completely before using it again.

• Never attempt to disassemble, repair or modify the device in any way. Disassembly, modification or any attempt at repair will void the warranty and may result in damage to the device or even injury or property damage.

• Do not store or carry flammable liquids, gases, or explosive materials in the same place as the
  device, its parts, or accessories.

• Overheating can damage the device.

CLEANING AND STORAGE

• After epilation, switch off the device and let it cool down. Be sure to unplug it. Inspect all parts for damage and then wipe them with a cloth or other lint-free material – it can be slight-ly damp. Do not wash or immerse the device in water or other liquids.
• Store the device in a dry place where it will not collect dust, at a temperature from 0°C to 40°C. Protect the treatment window and skin sensor from damage.

SIDE EFFECTS

• Depending on your skin type, using the device may be slightly uncomfortable. It may cause some heat or reddening of the skin. This is a normal.
• Adverse reactions usually occur immediately after application or within 24 hours. In rare cases, they may appear later. If you get an unusual reaction, talk to your doctor.

TROUBLESHOOTING

contact with the skin properly and that the lights are blue.
Constant blue indicator light.| Make sure that the lamp is not located in an area where there are metal parts or the effects of inductive capacity.
Device does not work in small areas.| Use the correct lamp head for small areas or areas that are difficult to access. It is necessary to ensure that the skin sensors are in contact with the skin.
Device is broken, cracked or does not visually look right.| If you have any doubts about the safe use of the devi- ce or damage to the device, do not use it and contact the manufacturer.
The LCD display shows E0.| Something happened to the fan. After the device cools down, turn it off and on again.
The LCD display shows E1.| Voltage problem. Contact the manufacturer.
The LCD display shows E2.| Improperly installed lamp head. Remove the lamp and

__replace it according to the manual.

If a malfunction occurs while using the device, follow the instructions below to find a solution. If you do not find the answer to your problem here, please contact the manufacturer‘s customer service.

TECHNICAL SPECIFICATIONS

_
_Frequency_| 50/60 Hz
_Operating temperature_| 5 – 35°C
_Storage temperature_| 0 – 40°C
_Storage humidity_| 25% – 75% RH
Operating pressure| 860 – 1060 Pa
_Emitted wavelengths_| 510 – 1100 nm
_Optical light_| 2.8 – 4.8 J/cm² according to the selected setting
_Maximum optical energy_| 14.88 J
_Pulse duration_| 1 – 3 ms
Number of levels| 1 – 5
Number of flashes| 600 000

FURTHER INFORMATION

1. For households: The symbol (crossed-out wheelie bin) on the product or in the accompa-nying documentation means that used electrical and electronic products must not be disposed of along with your other household waste. In order to dispose of the product properly, please return it to a designated collection point, where it will be accepted free of charge. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in penalties in accordance with nati-onal regulations. Information for users on disposal of electrical and electronic equipment (cor-porate and business use): For proper disposal of electrical and electronic equipment, please contact your dealer or supplier for detailed information. Information for users on disposal of electrical & electronic equipment in other countries outside the European Union: The above symbol (crossed-out wheelie bin) is only valid in European Union countries. For proper disposal of electrical and electronic equipment, request detailed information from your authorities or equipment dealer. Everything is expressed by the crossed-out wheelie bin symbol on the pro-duct, packaging, or printed materials.
2. Apply for warranty repairs of the device at your dealer. In case of technical problems and questions, contact your dealer, who will inform you about the further steps to be taken. Follow the rules for working with electrical equipment. The user is not authorized to disassemble the device or replace any part of it. There is a risk of electric shock when opening or removing covers. You also run the risk of electric shock if the device is incorrectly assembled and reconnected. The warranty period for the products is 24 months, unless otherwise stated. The warranty does not cover damage caused by non-standard use, mechanical damage, exposure to aggressive conditions, handling contrary to the manual and normal wear and tear. The manufacturer, importer or distributor are not liable for any damage caused by installation or improper use of the product.

DECLARATION OF CONFORMITY

The company elem6 s.r.o. hereby declares that all TrueLife devices are in compliance with the essential requirements and other relevant provisions of Directives 2014/30/EU and 2014/35/EU. The products are intended for sale without restriction in Germany, the Czech Republic, Slovakia, Poland, Hungary and other EU member states. The declaration of conformity can be downloaded from the web at www.truelife.eu/support/doc.

Manufacturer:
elem6 s.r.o., Braškovská 15, 16100 Prague 6, Czech Republic Printing errors and changes to the manual reserved.

References

• Declaration of Conformity – TrueLife.eu

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>