anslut 006251 Energy Meter Instruction Manual

Table of Contents

anslut 006251 Energy Meter

Only intended for indoor use.
Do not connect appliances that need a current of more than 16 A.
Do not connect appliances with an output of more than 3600 W.
The energy meter must not be used for voltages higher than specified in the technical data.
Always check that the plug on the connected appliance is fully inserted into the socket on the energy meter.
If the energy meter needs cleaning, unplug it from the mains and wipe it with a dry cloth.
Do not immerse the energy meter in water or any other liquid.

| Approved as per applicable directives
---|---
| Recycle discarded product as electrical waste.

Measures the power consumption of connected appliances. Shows total cost, power consumption and power saving.
The memory stores the values for cost, tariff and kWh if there is a power failure.
Can synchronise consumption of kWh with electricity meter in home for calculation.
Shows up to 14 values:
– time
– total cost
– cost 1
– cost 2
– tariff
– total consumption (kWh)
– consumption 1 (kWh)
– consumption 2 (kWh)
– active output (W)
– apparent output (VA)
– voltage (V)
– current (A)
– frequency (Hz)
– power factor.

MENU

When MENU is pressed in normal display mode the information is shown on the top half of the display.
When MENU is pressed in settings mode the settings are saved and settings mode ends.

SET

When SET is pressed in normal display mode it switches to settings mode.
In settings mode SET is used for the settings.
When pressed in normal display mode the information is shown on the bottom half of the display.
Switch on or off the blue display light by pressing for three seconds.
Press and+ at the same time for three seconds to switch off the energy meter.
In settings mode it is used to change the set va I ues

+

When+ is pressed in normal display mode the clock switches from 12 to 24 hour displaying.
When + is pressed for more than 3 seconds in normal display mode the display of accumulated consumption of energy and cost is reset.
When + is pressed at the same time for ionger than 3 seconds in normal display mode the energy meter switches off.
In settings mode the set value increases one step every time+ is pressed.

RST

Press RST to reset the energy meter. The values for cost, tariff and consumption of energy are kept.

Time – Tariff 1- Start time tariff 1- End time tariff 1-Tariff 2- Start time tariff 2- End time tariff 2.

When using the energy meter for the first time the display may be indistinct or the shown values incorrect. This is usuallybecause the battery is flat. Plug the energy meter into a power point for at least 5 hours, with the backlight off, to charge the built-in battery. Then press RST to start using the energy meter. Leave the energy meter plugged into a power point for at least 48 hours, with the backlight off, to charge the battery if the energy meter is not going to be used for some time.
Switch off the energy meter by pressing and+ at the same time for longer than 3 seconds if the energy meter is not going to be used for some time.

Press SET in normal display mode to switch to settings mode and press repeatedly to go to tariff settings. Now press EEi to select the figure to set.
The selected figure flashes. Press+ to increase the value by 1. The settings range is 00.00 to 99.99.
Two different tariffs can be set. Set tariff 2, or press MENU to save the setting and exit settings mode.
The standard setting for both tariffs is 00.00.

Press SET in normal display mode to switch to settings mode and press repeatedly SET to go to tariff period setting as per the sequence. Now press EEi to select the figure to set.
The selected figure flashes. Press+ to increase the value by 1. The settings range is from 00:00 to 23:59.
wo tariff periods can be set. Set tariff period 2, or press MENU to save the setting and exit settings mode
The standard setting for tariff period 1 is 00:00 to 08:00, for tariff period 2 it is 09:00to 23:00