alula RE703 Connect+ 1080p WiFi Video Doorbell Camera User Guide

alula RE703 Connect+ 1080p WiFi Video Doorbell Camera

Box Contents

Mounting Plate
(x2) Pick the one for best surveillance angle.

Plate Foam (x1)
Stabilize the mounting plate when installing it on the rough surface.

Doorbell (x1)

Tools You May Need:

Basics

• Name               Description

• LED Indicator: Red
  • Solid Red: Doorbell is starting up.
  • Fast-flashing Red: Doorbell exception (e.g. Micro SD card error).

• LED Indicator: Blue
  • Solid Blue: Doorbell is functioning properly.
  • Fast-flashing Blue: Doorbell is ready for Wi-Fi connection

• Micro SD Card(sold separately): Initialize the card in the Alula app before using it.

• Reset Button: Hold for 5 seconds to reset and enter to Wi-Fi configuration mode.

Get the Alula App

1. Connect your mobile phone to Wi-Fi (suggested).o Wi-Fi (suggested).
2.  SearSearch for “ch for “AlulaAlula” in App St” in App Store or Google Play or Google PlayTMTM..
3. Download and install the Alula app. Download and install the Alula app.
4.  Launch the app, sign it launch the app, and sign into a user account.o user account.

Wiring Overview

Alula doorbell with chimeAlula doorbell with chime
If you have a mechanical chime or electronic chime installed in your home, install the power kit and doorbell, and connect the wires as shown in the figure below.

Alula doorbell with no chimeAlula doorbell with no chime
If no chime is installed, skip power kit installation, install the doorbell, and connect the wires as shown in the figure below.

•  We recommend installing a new transformer to bring the output 12 to 24 volts.
•  Please refer to Quick Start Guide of your chime or transformer for the chime or transformer installing details.

Power Kit Installation

The power kit ensures that your doorbell gets the power it needs, so be sure to install it before you install your Doorbell.

• Shut off ff the electricity it at the barber that controls ls odorless car circuit.cut.

•  Insert one end of the wire harness into the power kit.

• Remove the cover from your mechanical chime.

•  RemoRemove ve the existing ting chime wires in the terminals named TRANS and FRONTTRANS and FRONT..

•  Connect the wire harness to the chimes the chime’s terminals named s terminals named TRANS and FRONTTRANS and FRONT..

•  InserInsert t the existing crime e write e and the other end of of the wire chains I into to three wi were con connector or add t that t tiny. Ry. Repeat this step with the other chime wire.this step with the other chime wire.

• Mount the power kit to the side of the chime. o the side of the chi

•  Put back the chime cut back the chime cover..

Doorbell Installation

• Shutt off the electricity y at he breaker that hat cols doorbell car circuit.cut.

• (Optional) When the wall is uneven, paste the plate foam to the mounting plate.

• Using your mounting plate as a template, mark the location of the two mounting holes on your wall, and insert anchors, then fix the mounting plate to the wall

• Recommended Hole Depth: 25 to 30 mm (1 inch to 1.2 inches).

If you have a chime installed, follow Option A; If not, follow Option B.

Option A Connect doorbell with your existing doorbell wires.

Option B Connect the fuse wire with your existing doorbell wire.

•  Install the doorbell to the mounting plate.

• Install the doorbell to the mounting plate. secure the doorbell

• Restore the electricity at the breaker.

• The doorbell is powered on when its indicator flashes blue quickly. If not, make sure your electricity is off and check the wiring. If yes, proceed to doorbell setup.

Doorbell Setup

•  Add your doorbell to Alula app.
  Remove the faceplate of the doorbell.

• Log in to your Alula account.

•  In the Cameras tab, tap “+” on the upper-right corner to go to the Scan QR Code interface.

•  Scan the QR code on the device or the cover of this quick start guide when the indicator flashes blue.

• start guide when the indicator flashes blue.

If you want to change the Wi-Fi which your doorbell has connected to, press and hold the reset button for 5s and repeat this part.

•  Put the faceplate back.

• Choose the corresponding chime type.
  In the Alula app, tap the Chime Type in the Device Settings interface to go to the Chime Type interface.
  Choose the chime type which you have installed in your home.

Install the Micro SD Card

• Remove the cover on the side of the doorbell with the screwdriver.
• Insert a micro SD card (sold separately) into the slot until a click.
• Place the cover back on, and tighten the screws with the screwdriver.

x

After installing the micro SD card, you should initialize the card in the Alula app before using it.

Initialize Micro SD Card

•  In the Alula app, tap the Storage Settings in the Device Settings interface to check the micro SD card status.
• If the card status displays as Uninitialized, tap to initialize it.
•  The status will then change to Normal and it can store videos.

Troubleshooting

1.  has installed my doorbell, but the chime in my home doesn’t function.
   Please confirm the following details.

2.  Make sure the right input voltage range (12V to 24V) has been used. Your doorbell is designed to work with at least 12 volts of AC power, which is in line with a majority of standard doorbell systems. Doorbell running at a lower voltage (or runs on DC rather than AC) may cause chime malfunction.

3.  Select the right chime type (same as the product label) in the Alula app.

4.  Power on the doorbell and wait for 10 minutes to 3 hours, and then try again.

I have failed to connect my doorbell to Wi-Fi.

1. Make sure your doorbell is not blocked by firewall or any limitation in your network.
2.  Do not connect too many devices to the router.
3.  Make sure the static IP setting is disabled and the router can distribute IP address to your device (DHCP is on).

My doorbell is offline frequently.

1.  Make sure the doorbell has received a strong and stable Wi-Fi signal.
2. Make sure your router and the internet is functional.
3.  The doorbell requires at least 2 Mbps uploading speed, please make sure the bandwidth of the network is sufficient, and do not have too many devices connected to the router.
4. If all the troubleshooting techniques listed above do not resolve the problem, please delete the device from your Alula account, reset and re-add.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>