EBECO Multiflex 27 Snowmelt Instruction Manual
- June 12, 2024
- EBECO
Table of Contents
- EBECO Multiflex 27 Snowmelt
- Product Information
- General instructions for Multiflex 27 and Ebeco Snow Melt
- Product Specifications
- Warranty Information
- Product Usage Instructions
- Laying Instructions for Ebeco Snow Melt
- Specifik laying for Multiflex 27, ground heating – snow melting
- Terms of Warranty
- Test report (Snowmelt, Snowmat, MI-60 and Multiflex 27)
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
EBECO Multiflex 27 Snowmelt
Product Information
The Snowmelt Multiflex 27 is a high voltage system designed for melting snow. It is available in different power options, ranging from 630W to 4250W, and comes in various widths. The system is resistant to different temperatures, with resistance values ranging from 12.5 to 85.
Welcome
Thank you for choosing Ebeco. For the warranty to be valid, the product must
be installed and handled as indicated in this manual. It is therefore
important that you read the manual. If you have any questions, please contact
us at Ebeco. Call +46 31-707 75 50 or send an e-mail to
support@ebeco.se. Feel free to visit
ebeco.com for more information.
Important
The system is a high voltage system and must thus be installed according to
applicable regulations and under the supervision of an authorised electrician.
For the warranty to apply, the guarantee certificate must be correctly and
completely filled in, and signed by an authorised electrician.
- The mat is normally laid about 30-70 mm under the finished surface. If it is laid deeper, the system will react slower.
- The heating cable and mat have a built-in return conductor. This means that connections are made at one end only.
- Multiflex 27 heating cable and Ebeco Snow Melt is delivered with a 5 m cold cable.
- The heating cable and mat are intended to be installed in a bed of sand under an asphalt or stone surface. It can also be laid in a fine mix over a concrete slab or fixed to reinforcing steel for embedding in concrete.
- If the mat is laid in a sand bed or on top of a concrete slab in accordance with these instructions, the depth to the underside of the surface finish must be 30 mm.
- The mat/cable can be laid deeper but it will make the system react slower, and this is particularly undesirable where control using temperature and humidity sensors is concerned.
- If the installation is controlled by a thermostat, the sensor must be installed in a VP conduit midway between two runs of cable.
- For larger installations (>5 kW) we recommend temperature- and humiditybased control. This type of control can give an energy saving of up to 75 %.
Always follow the general instructions first, before you move on to the specific instructions for the product you are using.
General instructions for Multiflex 27 and Ebeco Snow Melt
- Check that the hardware supplied agrees with the details on the delivery note.
- Measure the insulation of the heating cable/mat. It should be at least 10 MΩ. Measure the resistance of the cable/mat; see the figures in the table below. The readings may vary by ±10%. Enter the readings in the test report.
- The cold cable splice must be laid in the sand/concrete. The heating cable must not be cut. You may only shorten the cold cable.
- The cable runs must be separated and must not cross. Minimum spacing 70 mm.
- The cable must not cross expansion joints.
- The insulation and resistance of the cable must be measured before and after embedding in concrete/surface finishing. This ensures that any damage to the cable during laying is detected. Enter the readings in the testreport.
- Fill in and set up the heating cable signs at the relevant junction boxes. There must be a sketch of the heating cable/mat layout at the distribution board. For other documentation, see Swedish Standards.
Riding your bike is only a few steps away.
For your convenience, your n+ Mercedes Formula E Team eBike is delivered to
you mostly assembled. This User Manual contains a few steps in completing the
assembly of your bike. Make sure you read your User Manual prior to commencing
assembly and riding. If you need support with assembly, please scan the below
QR code for our global service centers or head to nplusbikes.com to search for
a center near you. Make sure you read your n+ Mercedes Formula E Team eBike
User Manual prior to commencing assembly and riding. For peace of mind, your
n+ Mercedes Formula E Team eBike comes with a 5 year frame warranty, and 2
year warranty on parts. You can find your warranty outline in section 6.
WARNING: This warranty does not cover incorrect assembly or installation of parts. To find a recommended service center near you, please head to nplusbikes.com, or alternatively a local reputable bike shop.
Product Specifications
Article Number | Description | Power | Width | Resistance |
---|---|---|---|---|
89 607 58 | Multiflex 27 | 630 W | 23.5 m | 85 |
89 607 60 | Multiflex 27 | 1000 W | 37 m | 52 |
89 607 62 | Multiflex 27 | 1300 W | 46 m | 41 |
89 607 64 | Multiflex 27 | 1500 W | 55 m | 35 |
89 607 66 | Multiflex 27 | 1850 W | 68 m | 29 |
89 607 68 | Multiflex 27 | 2150 W | 79 m | 25 |
89 607 70 | Multiflex 27 | 2700 W | 99 m | 20 |
89 607 72 | Multiflex 27 | 3200 W | 120 m | 16 |
89 607 74 | Multiflex 27 | 3650 W | 132 m | 14.5 |
89 607 76 | Multiflex 27 | 4250 W | 156 m | 12.5 |
Warranty Information
The Snowmelt Multiflex 27 is covered by a warranty. To ensure the warranty is valid, the product must be installed and handled according to the instructions provided in the manual. The warranty certificate must be correctly filled in and signed by an authorized electrician.
Product Usage Instructions
General Instructions
Before using the Multiflex 27 or Ebeco Snow Melt system, it is important to follow these general instructions:
- The system should be installed according to applicable regulations and under the supervision of an authorized electrician.
- Ensure the guarantee certificate is correctly and completely filled in and signed by an authorized electrician for the warranty to apply.
- Read the entire manual carefully before proceeding with the installation.
Laying Instructions for Ebeco Snow Melt
Follow these specific laying instructions for installing the Ebeco Snow Melt system:
Laying in sand or on a concrete slab:
- Determine if the mat needs to be stretched and mark on the ground how it will be laid.
- Calculate how the mat should be cut based on the stretch required.
- Prepare the bed on which the mat will be laid, ensuring there are no sharp stones or objects sticking up.
- Start at the connection end and roll out the mat.
- Cut the rubber tapes and roll the mat back.
- If the mat is stretched, apply loads to the ends until it is covered with sand or concrete.
Laying in sand or similar:
Place 1×4 inch boards on the mat, three on each length (1 metre mat width)
to keep the mat in place. Cover the mat with sand, crushed stone or similar,
levelling off the sand to the boards. Remove the boards and fill the gaps. This
will give about 20 mm of covering. If a thicker covering is needed, use
thicker boards.
Laying on reinforcing steel:
Determine the c/c distance. Lay reinforcing at that spacing. Roll out the
mat, stretch it if necessary and secure the cable to the reinforcing. If
necessary, cut the rubber tapes, roll back the mat and secure the cable to the
reinforcing. The cable must be supported by reinforcing steel along its entire
length to protect the cable during pouring of the concrete.
Specifik laying for Multiflex 27, ground heating – snow melting
To facilitate placement of the cable, the package contains a plastic drum holder. Place the drum holder in the perforated hole underneath the bottom of the package. Lift the drum on to the drum holder and place a weight on the lid of the package. When you pull the cable, the drum is spinning. The normal centre-to-centre (c/c) distance is about 100 mm. To obtain the exact c/c distance, measure the surface where the cable is to be laid and divide it by the length of the cable. When laying in a sand bed or similar
- Check that there are no sharp stones or other objects sticking up from the bed. The cable must be laid in a sand bed, in crushed stone or similar fine material so that it is covered to a depth of about 20 mm. This is to give the cable both mechanical and thermal protection. When steel spacers (89 350 35, 10 m) are used, fix them at right angles to the run of the cable (c/c 600 mm). Roll out the cable starting at the junction box. Secure the cable to the steel spacers.
- When embedding in concrete, secure the cable to the reinforcing. The cable must be supported by reinforcing steel along its entire length to protect the cable during pouring of the concrete. Check that the cable will be at least 30 mm below the finished surface. Put the cable to the reinforcing steel with cable ties, for instance. When the cable is lashed, it must be lashed loosely so that it is not damaged.
Snowmelt
Snowmelt|
---|---
Art. no| Description| Power| Width| Length| Area 300 W/m2| Area 250 W/m2| Area
200 W/m2| Resistance
89 602 90| Snowmelt| 2200 W| 0,5 m| 14–22 m| 7 m²| 9 m²| 11 m²| 25 W
89 602 92| Snowmelt| 2700 W| 1 m| 9–13,5 m| 9 m²| 11 m²| 13,5 m²| 20 W
89 602 94| Snowmelt| 3600 W| 1 m| 12–18 m| 12 m²| 14,5 m²| 18 m²| 14,5 W
89 602 96| Snowmelt| 4250 W| 1 m| 14–21,5 m| 14 m²| 17 m²| 21,5 m²| 12,5 W
Delivered with a 5 m cold cable. Voltage: 230V. The sign ” Heating cable system” is included in the package.
Multiflex 27
Art. no| Description| Power| Length| Area 300 W/m2
c/c 90 mm
| Area 250 W/m2
c/c 110 mm
| Area 200 W/m2
c/c 130 mm
| Resistance
---|---|---|---|---|---|---|---
89 607 58| Multiflex 27| 630 W| 23,5 m| 2,1 m²| 2,6 m²| 3,0 m²| 85 W
89 607 60| Multiflex 27| 1000 W| 37 m| 3,5 m²| 4 m²| 5 m²| 52 W
89 607 62| Multiflex 27| 1300 W| 46 m| 4,5 m²| 5 m²| 6,5 m²| 41 W
89 607 64| Multiflex 27| 1500 W| 55 m| 5 m²| 6 m²| 7,5 m²| 35 W
89 607 66| Multiflex 27| 1850 W| 68 m| 6 m²| 7,5 m²| 9 m²| 29 W
89 607 68| Multiflex 27| 2150 W| 79 m| 7 m²| 8,5 m²| 11 m²| 25 W
89 607 70| Multiflex 27| 2700 W| 99 m| 9 m²| 11 m²| 13,5 m²| 20 W
89 607 72| Multiflex 27| 3200 W| 120 m| 11 m²| 13 m²| 16 m²| 16 W
89 607 74| Multiflex 27| 3650 W| 132 m| 12 m²| 14,5 m²| 18 m²| 14,5 W
89 607 76| Multiflex 27| 4250 W| 156 m| 14 m²| 17 m²| 21,5 m²| 12,5 W
Delivered with a 5 m cold cable. Voltage: 230V. The sign ” Heating cable
system” is included in the package.
Delivered with a 5 m cold cable. Voltage: 230V. The sign ” Heating cable system” is included in the package.
Terms of Warranty
**Snowmelt, Snowmat, MI-60 and Multiflex 27***
Ebeco AB provides a 10 year guarantee for defective materials in Snowmelt, Snowmat, MI-60 and Multiflex 27. The guarantee only becomes valid under condition that the installation is carried out by a qualified electrician according to the applicable regulations and in accordance with installation instructions issued by Ebeco. This guarantee certificate, inclu-ding the test record below, must be completed in its entirety and, along with the materials specification or invoice, must be signed by the electrician who carried out the installation. Furthermore, there must be photographs/sketches that show the mat in its entirety after laying but before covering. If defects should arise during the guarantee period, Ebeco AB undertakes to repair or alternatively replace Snowmelt/Snow mat/Multiflex at no cost to the purchaser. Ebeco AB also undertakes to restore the surface coating to its original condition after the repair or replacement has been completed. In order to be able to remedy the fault, the purcha-ser must have saved or have access to 1 m² of the existing surface material. For any controls (timer/panelboard), where defects occur after 3 years, Ebeco AB will supply a new control. The guarantee does not apply to installations that have been carried out by an unqualified electrician or alternatively if an unqualified electrician has carried out modifications or repairs. Nor does the guarantee apply if the defect has arisen as a re-sult of using incorrect materials and construction or as a result of incorrect installation. Nor is damage covered that is a result of vandalism, fire, lightning, water damage or damage caused by negligence, abnormal usage or as a result of an accident. In the event of a material defect that is covered by the guaran-tee Ebeco AB must be notified. In the event of the guarantee being invoked, this guarantee certificate with accompanying invoice of installation, material specification plus completed and signed test record must be presented.
EBECO AB
Martin Larsson, CEO
*Applies only under condition that the product is installed together with Snowmat timer, E 18 970 77, or Ebeco’s panelboard.
Test report (Snowmelt, Snowmat, MI-60 and Multiflex 27)
Before laying | After fixing | After surface coating/ embedding | |
---|---|---|---|
Mat/Cable no. 1-6 | Resistance value | Insulation value | Resistance value |
Insulation value | Resistance value | Insulation value | |
No. 1, Art.no: ……………. | |||
No. 2, Art.no: …………… | |||
No. 3, Art.no: …………… | |||
No. 4, Art.no: …………… | |||
No. 5, Art.no: …………… | |||
No. 6, Art.no: …………… |
Min. insulation value 10 MΩ.
The system is documented with photos/drawings
Electrical installation carried out by:
Date: ………………………………………………………………. ……………………………………………………………………….
Signature: ………………………………………………………… according to the attached materials
specification.
EBECO AB
Lärjeågatan 11
SE-415 02 Göteborg, SWEDEN
Phon e +46 31 707 75 50
ebeco.com
info@ebeco.se
Manual Snowmelt MF27 220323
For any further questions or assistance, please contact Ebeco at +46 31-707 75 50 or send an email to support@ebeco.se. Visit ebeco.com for additional information.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>