Shenzhen Ktc Commercial Display Technology PW.3.15000.0155 KTC Commercial Display Technology CO.,LTD User Manual

: June 5, 2024
: Shenzhen Ktc Commercial Display Technology

Table of Contents

Product Descrition：
Product Specification
FCC Statement
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KTC Commercial Display Technology CO.,LTD.
WIFI Module
Model Number: PW.3.15000.0155

Product Descrition：

This document is to specify the product requirements for 802.11a/b/g/n/ac and Bluetooth USB Module. This Card is based on REALTEK RTL8822BU chipset It is a complete dual-band(2.4GHz and 5GHz)WIFI 2 2 MIMO MAC/PHY/Radio System- on-a-Chip. This module provides a high level of integration with a dual-stream IEEE 802.11ac MAC/ baseband /radio and Bluetooth 4.1 and 4.2LE. The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 866.7Mbps. It is also backward complied with IEEE 802.11a standard from 5.15-5.825GHz wideband and IEEE 802.11b/g standard from 2.4-2.5GHz. It can be used to provide up to 54Mbps for IEEE 802.11a and IEEE 802.11g, 11Mbps for IEEE 802.11 b, and 300Mbps for IEEE 802.11 n.

Product Specification

For 2.4 GHz ISM Band of Wi-Fi

Frequency Band:| 2400 MHz to 2483.5 MHz
Frequency Range:| 2412 MHz to 2462 MHz
Support Standards:| IEEE 802.11b, IEEE 802.11g, IEEE 802.11n-HT20, IEEE 802.11n-HT40
Type of Modulation:| IEEE 802.11b: DSSS(CCK, DQPSK, DBPSK)
IEEE 802.11g: OFDM(64-QAM, 16-QAM, QPSK, BPSK)
IEEE 802.11n-HT20: OFDM(64-QAM, 16-QAM, QPSK, BPSK)
IEEE 802.11n-HT40: OFDM(64-QAM, 16-QAM, QPSK, BPSK)
Data Rate:| IEEE 802.11b: Up to 11 Mbps
IEEE 802.11g: Up to 54 Mbps
IEEE 802.11n-HT20: Up to MCS15
IEEE 802.11n-HT40: Up to MCS15
Number of Channels:| IEEE 802.11b: 11
IEEE 802.11g: 11
IEEE 802.11n-HT20: 11
IEEE 802.11n-HT40: 7
Channel Separation:| 5 MHz
Antenna Type:| Chain 0| External Antenna
Chain 1| External Antenna
Antenna Gain:| Chain 0| 2.06 dBi
Chain 1| 2.06 dBi
For 5 GHz U-Nll Bands of Wi-Fi

Frequency Bands:| 5150 MHz to 5250 MHz (U-NII-1)
5250 MHz to 5350 MHz (U-NII-2A)
5470 MHz to 5725 MHz (U-NII-2C)
5 725 MHz to 5 850 MHz (U-NII-3)
Frequency Ranges:| 5180 MHz to 5240 MHz
5260 MHz to 5320 MHz
5500 MHz to 5700 MHz
5 745 MHz to 5 825 MHz
Support Standards:| IEEE 802.11a/n/ac
TPC Function:| Not Support
DFS Operational mode:| Slave without radar Interference detection function
Type of Modulation:| IEEE 802.11a: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11n: OFDM(64QAM, 16QAM, QPSK, BPSK)
IEEE 802.11ac: OFDM(256QAM, 64QAM, 16QAM, QPSK, BPSK)
Channel Spacing:| IEEE 802.11a/n-HT20/ac-VHT20: 20 MHz
IEEE 802.11n-HT40/ac-VHT40: 40 MHz
IEEE 802.11ac-VHT80: 80 MHz
Data Rate:| IEEE 802.11a: Up to 54 Mbps
IEEE 802.11n-HT20: Up to MCS15
IEEE 802.11n-HT40: Up to MCS15
IEEE 802.11ac-VHT20: Up to MCS8
IEEE 802.11ac-VHT40: Up to MCS9
IEEE 802.11ac-VHT80: Up to MCS9
Number of Channels:| 5150 MHz to 5250 MHz:
4 for IEEE 802.11a/n-HT20/ac-VHT20 2 for
IEEE 802.11n-HT40)/ac-VHT40
1 for IEEE 802.11acVHT80
5250 MHz to 5350 MHz:
4 for IEEE 802.11a/n-HT20/ac-VHT20
2 for IEEE 802.11n-HT40)/ac-VHT40
1 for IEEE 802.11acVHT80
5470 MHz to 5725 MHz:
11 for IEEE 802.11 a/n-HT20/ac-VHT20
5 for IEEE 802.11n-HT40/ac-VHT40
2 for IEEE 802.11ac-VHT80
5725 MHz to 5850 MHz:
5 for IEEE 802.11a/n-HT20/ac-VHT20 2 for
IEEE 802. 11n-HT40/ac-VHT40
1 for IEEE 802.11ac-VHT80
Antenna Type:| Chain 0| External Antenna
Chain 1| External Antenna
Antenna Gain:| Chain 0| 5150 MHz to 5250 MHz: 1.67 dBi
5250 MHz to 5350 MHz: 1.75dBi
| | 5470 MHz to 5725 MHz: 2.8 dBi
---|---|---
5725 MHz to 5850 MHz: 1.12 dBi
Chain 1| 5150 MHz to 5250 MHz: 1.67 dBi
5250 MHz to 5350 MHz: 1.75 dBi
5470 MHz to 5725 MHz: 2.8 dBi
5725 MHz to 5850 MHz: 1.12dBi
For BT LE

Frequency Band:| 2400 MHz to 2483.5 MHz
Frequency Range:| 2402 MHz to 2480 MHz
Bluetooth Version:| Bluetooth V4.2 LE
Type of Modulation:| GFSK
Number of Channels:| 40
Channel Separation:| 2 MHz
Antenna Type:| External Antenna
Antenna Gain:| 2.06 dBi
For BT EDR

NOTICE:
◆please keep this product and accessories attached to the places which children can’t touch;
◆do not splash water or other liquid onto this product, otherwise it may cause damage;
◆do not put this product near the heat source or direct sunlight, otherwise it may cause deformation or malfunction;
◆please keep this product away from flammable or naked flame;
◆please do not repair this product by yourself. Only qualified personnel can be repaired.

FCC Statement

– List of applicable FCC rules This device complies with FCC part 15C: 15.247&15.407
– Summarize the specific operational use conditions
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. And the module should be installed at a minimum distance of 20 cm away from a person nearby. The host product manufacturer should state this information to the host instruction manual.

– Trace antenna designs
Not applicable.

– RF exposure considerations
This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This modular must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

– Antennas
Antenna Type: External Antenna
Antenna Gain:
2.4G WIFI：2.06 dBi
5.2G WIFI：1.67 dBi
5.3G WIFI：1.75 dBi
5.6G WIFI：2.8 dBi
5.8G WIFI：1.12 dBi
B T:：2.06 dBi

– Label and compliance information
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: 2AQ5RWRTL8822BU Or Contains FCC ID: 2AQ5RWRTL8822BU”.

– Information on test modes and additional testing requirements
Any final host product with the modular transmitter installed should be under test according to the guidance given in KDB 996369 D04. To enter test mode for the module, RTLWlanU_WindowsDriver_1030.38.0803.2018_Drv_3.00.0031 production kit software and command is necessary. When something wrong happens in configuring test modes for host products with modules, the host product manufacturer should coordinate with the module manufacturer for technical support. It is recommended that some investigative measurements should be taken to confirm that the host product with the module installed does not exceed the spurious emissions limits or band edge limits.

– Additional testing, Part 15 Subpart B disclaimer
The modular transmitter is only FCC authorized for the specific rule parts (FCC Part 15.247&15.407) list on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed when contains digital circuity.

Canada Statement

This device complies with Industry Canada’s license-exempt RSS. Operation is subject to the following two conditions:

This device may not cause interference; and
This device must accept any interference, including interference that may cause undesired operation of the device.

The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems