TAYAMA TGS-300 Butane Gas Portable Stove Instruction Manual

: June 6, 2024
: TAYAMA

Table of Contents

IMPORTANT CAUTIONS
INSTALLING THE FUEL CARTRIDGE
HOW TO IGNITE AND ADJUST THE FLAME
HOW TO TURN OFF THE FLAME & TAKE THE CARTRIDGE OUT
HOW TO RESET THE SAFETY DEVICE
TROUBLE SHOOTING
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

INSTRUCTION MANUAL
BUTANE GAS
PORTABLE STOVE

(*) High safety function with direct gas cut-off device
Use new standard governor as Japan technology, automatically cut-off gas inside, Anti Explosion Safety Device
Materials & Accessories are used by prime grade as export standard JAPAN standard burner head system with the optimal capacity, low CO concentration (< 800PPM)
TAYAMA®
Tayama Appliance USA Inc www.tayama-usa.com
Before operating this unit, please read these instructions completely.

IMPORTANT CAUTIONS

FOR SAFE & EFFICIENT USE, READ THE INSTRUCTION MANUAL CAREFULLY AND FOLLOW MANUFACTURER’S INSTRUCTIONS.

Use only butane gas cartridges with low pressure (3-5 kg/cm2), do not use refilled, old, rusty, or deformed fuel cartridges.
Do not use fuel cartridges that exposure to sunlight or store at a temperature above 40°C.
Do not use the appliance in a windy place (Fig. 1)
Place the appliance on a stable and flat surface (Fig. 2)
Do not use an oversize pot with a diameter of bottom > 24cm (Fig. 3)

INSTALLING THE FUEL CARTRIDGE

Make sure the cartridge is not empty and follow article No. 3 to use the appropriate fuel cartridge.
Open the bomb cover, make sure the ignition knob is in OFF position (Fig. 4)
Put the fuel cartridge in the right position: locate the notch collar on top of fuel cartridge, align the notch collar with the fuel cartridge index arm (Fig. SA – SEI)
Press down the lock lever knob until it is in the LOCK position (Fig. 6) and close the bomb cover.
When the fuel cartridge is in the right position, the appliance is ready to ignite.

Attention: while installing the fuel cartridge, if you hear a hissing sound, take the cartridge out and reinstall. Do not ignite the appliance when the cartridge is not in the right position.

HOW TO IGNITE AND ADJUST THE FLAME

Turn the ignition knob to IGNITE position (Fig. 7) until you hear a “click”, the flame will ignite automatically.
If there is no flame, turn the ignition knob to the OFF position and repeat the ignition procedure.
If there is no flame after 4-5 attempts, follow article No. 8.
Turn the ignition knob from High to Low to adjust the flame from strong to small (Fig. 8).

Attention: After the first time ignition, the flame may not spread to the heated burner, after 10-15 seconds use or put the pot on the appliance, the flame is adjusted automatically and steady burn.

HOW TO TURN OFF THE FLAME & TAKE THE CARTRIDGE OUT

Turn the ignition knob to the OFF position (Fig. 9).
Lift up the lock lever knob to UNLOCK position to disengage the fuel cartridge from the governor (Fig. 10).
Open the bomb cover and remove the cartridge from the appliance.

Attention:

When interrupting use, turn the ignition knob to OFF position and switch lever knob to UNLOCK position to extinguish the flame and disengage the cartridge out of the governor.
After use, take the fuel cartridge out of the appliance.

HOW TO RESET THE SAFETY DEVICE

When using a fuel cartridge with high pressure (normally refilled cartridge) safety device will automatically close, refuse fuel flow into the governor –> no flame although ignite.

Follow article No. 4 to take the cartridge out of the appliance.
Turn the ignition knob to HIGH position to release fuel out of the governor (Fig. 11).
Press the reset knob (red color) until you hear a loud click to set the governor on the default setting (Fig. 12).
Replace a new fuel cartridge with acceptable pressure and follow article No. 2 to install.

Attention: Do not change the frame of the governor & other components of the appliance in any situation.

TROUBLE SHOOTING

If fail to ignite the burner after 4-5 attempts –> follow the below steps:
A) Check the fuel cartridge: If it is empty –> replace a new cartridge.
B) If there is fuel in the cartridge, a common problem is the pressure in a cartridge is too high (especially with refilled cartridge), safety shut-off device closed automatically, refuse fuel into the governor, see article No.5
C) If there is fuel in the cartridge & the pressure is acceptable (brand-new cartridge) –> Check the position of spark plug: the gap between the plug and the head burner is 3–>4 mm (Fig. 13)
D) If still cannot ignite, contact the supplier agent, store.

Do not change the frame of the governor in any situation.