Atomi Smart Coffee Maker with Grinder

Smart Coffee Maker with Grinder

Introduction

Overview

The Atomi Smart Coffee Maker with Grinder lets you brew your next cup of coffee from your phone anytime, anywhere! Set weekly schedules, turn your Smart Coffee Maker on and off automatically, and much more.

Cleaning your Smart Coffee Maker before first use

Make sure your first cup of coffee is as good as it can be by cleaning your Smart Coffee Maker before its first use. Just follow these simple steps:

1. Wash the carafe, carafe lid, and the filter basket in a mixture of mild detergent and water. Rinse each thoroughly.
2. Run a brew cycle with water only, without adding coffee and coffee filter.
3. When brewing is complete,  turn your Smart Coffee Maker off, discard the water in the carafe and rinse the carafe, lid, and filter basket.

Before you begin

1. Know your Wi-Fi network and password
2. Make sure your mobile device is running iOS® 8 or higher or Android™ 4.1× or higher
3. Make sure you’re connected to a 2.4GHz Wi-Fi network (Atomi Smart can’t connect to 5GHz networks).

Connecting Your Device

Step 1: Download App

Download the Atomi Smart app from the App Store or Google Play and create an account. If you already have the app installed, please make sure to check for any updates as they will improve your experience with the Atomi Smart app.

Step 2: Adding Your Device

1.  Select “Add Device” or click (+) at the top right corner of your device screen.

2.  Select Smart Coffee Grinder Maker from the device list.

Step 3: Connecting to Wi-Fi

1.  Enter your Wi-Fi network (2.4 GHz only) and password

2.  Press ‘Continue’

Step 4: Plug In

Plug your Atomi Smart Coffee Maker into any standard outlet

Step 5: Connecting Your Device

1.  Confirm that the Wi-Fi icon is flashing.

If the icon is not flashing, press and hold the ‘Wi-Fi’ button for 10 seconds or unplug and plug the device again.

2.  Press ‘Continue’

3. Read the instructions on your phone screen and press ‘Go to Connect’

4. On your phone’s Wi-Fi screen, select ‘atomi-smart-xxxx’

5. Once it connects, return to the Atomi Smart app and wait for the installation to be completed

iOS:  After connecting to the atomi-smart-xxxx, return to the app by pressing ‘Atomi Smart’ on the top left part of the screen, or by switching back to the atomi smart window

Android: After connecting to the atomi-smart-xxxx, some devices may display a message informing that you are “Connected without internet”. Please ignore this message and return to the app by pressing the back button on the bottom navigation bar (Do not press the back button on the top left part of the screen as this may bring you back to the ‘Settings’ page instead of the Atomi Smart app)

Your device is now connected!

IMPORTANT:  If you cannot see the ‘atomi-smart-xxxx’, press and hold the Wi-Fi button again for another 10 seconds and refresh your Wi-Fi list. The ‘atomi-smart-xxxx’ network should appear after a few seconds.

Controlling your Smart Coffee Maker

General

Brew ON/OFF – Start brewing and stop brew.

Brew Strength- Select coffee strength (Mild, Medium, Strong)

Schedule – Set a brewing schedule

Coffee Beans – Brew coffee using beans (Grinder will be activated)

Coffee Powder  – Brew coffee using powder

Schedule

1. Choose between “Coffee Beans” or “Coffee Powder”
2. Choose the  Brew Strength (Mild, Medium, Bold)
3. Select the time of the day to start brewing
4. Choose the days of the week to Repeat the schedule (if desired)
5. Turn on the “Enable this Schedule” switch to activate your schedule

Press “Save Changes” to save your schedule.

For more scheduling options, you can use the ‘Smart Scenes’ feature which allows you to create additional schedules, triggers and automations.

1. Open the Atomi Smart app
2. Select the ‘Smart Scenes’ tab and press the ‘+’ button
3. Select ‘Schedule’, enter the time/days of the week to repeat and ‘Continue’
4. Press ‘Execute Device Action’ and select your Coffee Maker. Choose the actions for the schedule (Example: Power ON, Brew Strength Strong) and press ‘Continue’
5. Review your schedule, enter a name (optional) and press ‘Save’.

You can create additional schedules for your coffee maker by repeating the steps above.

For more ‘Smart Scenes’ instructions visit  Triggers & Automations

Tip: The Atomi Smart Coffee Maker will keep your coffee warm for up to 4 hours.

You can also customize and set it to keep the coffee warm for a shorter period by following the steps below:

• Open the Atomi Smart app and press the ‘Smart Scenes’ tab

• Press the ‘+’ button and select ‘Device Status’

• Select your Coffee Maker, then press ‘Status’ and choose ‘Brewing Completed’

• Now press ‘Set next Action in’ and enter the amount of hours/minutes (less than 4 hours) that you want the coffee maker to stay in “Keeping Warm’ mode. Then, press ‘Continue’

•  Now press the ‘+’ button on the ‘Action’ section and select ‘Execute Device Action’

• Select your Coffee Maker, then press ‘Power’ and choose ‘Off’. Press ‘Save’ and ‘Continue’

• Review your Automation details and press ‘Save’

Measuring your Coffee

For best results, use a level tablespoon for ground coffee measurement. Make sure you use medium grind coffee for a perfect brew

Adding Water and Coffee beans / powder:

1 –  Open the top lid of the Smart Coffee Maker.

2 –  Place a 10-12 cup paper basket-style filter or the included reusable filter into the removable filter basket.

Note: If using paper filters, it is important that the sides of the filter fit flush against the side of the filter basket. If filter collapse occurs, dampen the filter before placing it in the filter basket. Add the desired amount of coffee and gently shake to level the coffee.

3 –  Fill the water reservoir with cold, fresh water to the desired capacity. For easy and accurate filling, the water markings on the water reservoir show the amount of water needed to make the corresponding desired number of cups. The LCD panel and app also indicate the current water level. DO NOT  fill past the “12 cup MAX line” or water will flow out of the Smart Coffee Maker.

4 –  Add coffee beans / powder to your Coffee Maker

Note: The amount of coffee brewed will always be slightly less than the amount of water poured into the water reservoir. This is due to the absorption of water by the coffee grounds.

Using your Smart Coffee Maker without the Atomi Smart app

1 –  Turn the Smart Coffee Maker on by pressing the POWER button once. If there’s enough water, the POWER button light will turn on to signal that the Smart Coffee Maker is ON and brewing.

Note:  Brew can be stopped by pressing the POWER button a second time.

2 –  After the used coffee grounds have cooled, carefully remove the filter basket and discard them.

Note:  The brew basket drawer is hot after brewing. Always allow the Smart Coffee Maker to cool down before cleaning.

3 –  Make sure the Glass Coffee Carafe is empty and in place before starting to brew coffee.

4 –  Be sure to turn your Smart Coffee Maker off when no longer using it.

Cleaning and Maintaining your Smart Coffee Maker

Daily Cleaning –  Always unplug the Smart Coffee Maker and allow it to cool before cleaning.

• Remove and wash the filter basket, permanent filter, carafe, and carafe lid in a solution of hot water and mild liquid soap.
• Never use abrasive cleaners, steel wool pads, or other abrasive materials.
• CAUTION:  Never immerse the Smart Coffee Maker itself in water, in any other liquid or place the machine in the dishwasher.

1 – Fill the carafe with a solution of equal parts water and vinegar and let the solution stand in the carafe for approximately 20 minutes.

2.  Discard the solution, then wash and rinse the carafe. Do not use harsh abrasive cleaners that may scratch the carafe.

The glass carafe is dishwasher safe ✓

Note: Leaving the carafe on the hot plate with a low amount of coffee for longer than 2 hours may cause the water to evaporate and make the coffee bitter/burnt. It’s recommended to turn off the machine once the carafe has less than 2 cups of coffee.

You  MUST  clean your Atomi Smart WiFi Coffee Maker with Grinder from time to time. If the grinder is not cleaned, bean particle and oil accumulation will eventually start clogging the mechanism and it will stop working. By cleaning your device, you will keep it working well and properly.

The  frequency of cleaning depends on how often you use the grinder. It also depends on the type of beans that you use, because some are very oily. Atomi recommends that you clean your Atomi Smart WiFi Coffee Maker with Grinder at least once a month. The more often you clean the grinder, the less the accumulation.

Cleaning instructions (Grinder)

CAUTION: ALWAYS unplug the electrical supply cord prior to cleaning the grinder and allow it to cool. NEVER clean the grinder using running water. NEVER use abrasive cleaners or chemical solvents.

1 – Remove the 4 screws from the bean compartment

2 –  Remove the screw from the grinder.

3 –  This is the part that must be cleaned. You cannot remove any other piece. Use a coffee grinder cleaning brush, toothbrush, paper towel, or a tweezer to remove excess beans particles and oils. You can also use blown air to dislodge anything remaining.

FAQ & Troubleshooting

What are the available voice commands?

Alexa

“Alexa, turn on [device name]”

“Alexa, turn off [device name]”

“Alexa, set the [device name] to mild”

“Alexa, set the [device name] to medium”

“Alexa, set the [device name] to strong”

“Alexa, what is the [device name] brew strength? “

__Google Assistant

“Hey Google, turn on [device name]”

“Hey Google, turn off [device name]”

“Hey Google, what is the status of the [device name]?”

I’m having issues to connect. Why do I need to connect to a 2.4GHz

network?

In order to successfully connect Atomi Smart devices, a 2.4GHz connection is required.

The 2.4GHz frequency waves travel further than the 5GHz. This means that if your device is in another room or far from your phone, you will have a better signal reception (compared to 5Ghz) which is essential for your smart device to function correctly and stay online.

All modern routers come with 2.4GHz and 5GHz. Depending on your router type, these bands may appear as separate WiFi networks (Example: Name-2.4GHz and Name-5GHz) or combined. If you only have one WiFi network, you should still be able to connect since the Atomi Smart app automatically finds the 2.4GHz frequency when connecting to your router.

However, if you experience any issues, please follow the points below:

• Make sure that you are connecting to a 2.4GHz network
• Keep your mobile device close to the router during connection
• If you have two SSID for your WiFi (Example: Name-2.4GHz / Name-5GHz), please temporarily disable “Auto-Join” on your Name-5GHz network)
• If you have two SSID for your WiFi, make sure that your 2.4GHz and 5GHz WiFi have different names
• If your router gives the option to disable the 5GHz network, please disable it temporarily
• Disable any VPN apps/services in order to connect successfully
• If you are having issues to connect, turn on Airplane Mode (Keep only WiFi activated when connecting your smart device)
• Make sure that you’ve entered the correct password for your 2.4GHz WiFi on the “Select 2.4GHz Wi-Fi Network” screen (Case sensitive, and make sure that there are no extra spaces)
• If you have too many devices connected to your 2.4GHz (more than 10), please turn off some of them temporarily and retry connecting your smart device to the app
• If you have a Mesh router, you may not be able to manually switch to a 2.4GHz frequency. Since this frequency travels further than the 5GHz, you can force your device to connect to it by moving your phone far from the router
• If you are still experiencing issues to connect, delete the app and reinstall it
• If the issue persists, restart your router

How to share my device with other users?

Please  click hereto learn more about device/group sharing

How to disable the beep?

Press and hold the ‘Brew Strength’ button (3 beans) on the coffee maker panel for 3 seconds.

In order to enable it, press and how the ‘Brew Strength’ button again for 3 seconds.

When I press the ‘Power’ button, it doesn’t start brewing

Make that the carafe is correctly placed on the hot plate. Also, confirm that the water tank has at least 2 cups of water.

I can’t find the atomi-smart-XXXX network in my Wi-Fi list

Make sure your atomi smartdevice is plugged in and the Wi-Fi light (or clock) is blinking. If not, unplug your Atomi Smart device and plug it back in to reboot. If you still cannot see the ‘atomi-smart-xxxx’, press and hold the “Coffee scoop” button for 10 seconds. The atomi-smart-XXXX should appear on your network list after a few seconds.

My Wi-Fi network doesn’t appear in the Atomi Smart app

Use your smartphone to confirm that you have at least two Wi-Fi bars in the vicinity of your Atomi Smart device. If not, move your Atomi Smart device closer to your router. (The list will refresh every 10 seconds).

Cannot connect to your WiFi network

Make sure you entered the correct WiFi password during the WiFi setup. Check if there are problems with your internet connection. If the WiFi signal is too weak, reset your WiFi router and try again.

My Atomi Smart device appears as “Unavailable” in the app

Refresh the device list.

My Atomi Smart app is frozen

Force quit and re-launch the Atomi Smart app.

How to reset my device

Press and hold the Wi-Fi button for 10 seconds.

I’m still having trouble!

Wi-Fi networks come in a lot of shapes and sizes with many quirks of their own. It doesn’t mean your Atomi Smart device is malfunctioning.

If problems persist, please try these steps, in this order:

1. Force quit and re-launch the Atomi Smart app. Check to see if this fixes the issue.

2. Unplug your Atomi Smart device and plug it back in. Check to see if this fixes the issue.

3. Unplug your router and plug it back in. Check to see if this fixes the issue.

4. Delete and reinstall the Atomi Smart app. Check to see if this fixes the issue.

Is this Smart Coffee Maker compatible with Alexa and Google Assistant?

Yes, the Atomi Smart Coffee Maker works with Alexa and Google Assistant

The Coffee is not brewing

1.  The Smart Coffee Maker is unplugged;  plug the Smart Coffee Maker back into the wall outlet.

2.  There’s a power outage; wait for power to be restored.

3.  The filter basket is not properly inserted; insert filter basket correctly.

4.  Carafe is not placed all the way on the warming plate; place carafe correctly on the warming plate.

The Smart Coffee Maker only brews water

There are no coffee beans/grounds in the machine; please add the desired amount of coffee

There are grounds in the coffee

The filter is not properly placed in the basket. Seat the filter properly within the filter basket.

The coffee is too bitter or burnt

Leaving the carafe on the hot plate with a low amount of coffee for longer than 2 hours may cause the water to evaporate and make the coffee bitter/burnt. It’s recommended to turn off the machine once the carafe has less than 2 cups of coffee.

Download User Guide

The Atomi Smart AT1489 Coffee Maker with Grinder User Guide -[ Download PDF ]

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>