Veise VE33B Fingerprint Smart Lock User Guide

Veise VE33B Fingerprint Smart Lock

Product Information

Specifications

• Product Name : Bluetooth Fingerprint Keypad Deadbolt Smart Lock
• Features: Keypad, Fingerprint Sensor, Emergency Key Override, Auto Lock Mode
• Power Source : Four AA alkaline batteries (not included)
• Compatibility: Requires the use of a dedicated mobile App for operation

Product Usage Instructions

Quick Start Guide

1. Follow the installation instructions provided in the manual to install the smart lock.
2. Download the dedicated App by scanning the QR Code provided in the manual.
3. Register, login to the App, and add the device by scanning the QR Code on the Battery Cover.
4. Complete the Bluetooth setup within the App.

At a Glance

The smart lock consists of an exterior assembly with Keypad, Fingerprint Sensor, Battery Cover, and Emergency Key Override Button. The interior assembly includes a Reset Button, Multifunction Button, and Thumb Turn for manual locking/unlocking.

How to Lock/Unlock

Unlocking the door from outside:

• Master/User PIN Code
• Fingerprint via the App

Unlocking the door from inside:
Rotate the thumb turn to the unlock position.

Locking the door from outside:

• Manually by pressing any button on the keypad or using Auto
• Lock Mode for automatic locking after 2 seconds

Locking the door from inside:
Rotate the thumb turn to the lock position. In Auto Lock mode, the device will lock automatically.

Definitions

• Master PIN Code: Required for programming and feature settings, can also unlock the door in vacation mode.
• Auto Lock: Automatically locks the door after a set time delay.
• Wrong Entry PIN Code Limit: Unit shuts down after 10 invalid attempts for 3 minutes.
• Silent Mode: Keypad can be muted while low battery and wrong entry alarms still sound.
• Low Battery Alarm: Indicates when batteries need replacement.
• Unlock With Fake Code: Prevents PIN Code exposure by entering random digits before/after the correct code.

Code Format
The code format allows for a combination of numbers to be used for secure access to the smart lock.

Frequently Asked Questions (FAQ)

• Q: Do I need to change the default Master PIN Code?
  A: Yes, for security reasons, it is recommended to change the default Master PIN Code before programming the lock.

• Q: How can I enable/disable the Auto Lock feature?
  A: You can enable/disable the Auto Lock feature and set the time delay in both Master Mode and the App settings.

Bluetooth Fingerprint Keypad Deadbolt Smart Lock
User Guide / Installation Instruction

Thank you for purchasing our products. Please review this manual thoroughly before operating your device. All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.

IMPORTANT:
The App is required to operate the lock. After the lock is properly installed, the first account to bind the lock will be the administrator.

QUICK START GUIDE

1. Follow the installation instructions to install the smart lock.

2. Scan the QR Code to download the App.

3. Register and login to the App. Add the device to your account by scanning the QR Code found on the Battery Cover.

4. Complete the Bluetooth setup in the App.
   

At a Glance

1. Pull the exterior assembly  from the button.
2.  Rotate from the top to open it, insert the key and rotate to unlock.

How to Lock / Unlock

• Unlocking the door from outside
• Unlocking the door from inside

• Locking the door from outside

• Locking the door from inside

Definitions

Master PIN Code

• Required for programming and feature settings, the Master PIN Code can be used to unlock the door while in vacation mode. The default Master PIN Code needs to be changed  before programming the lock for security reasons.

Auto Lock

• If the Auto lock feature is enabled, the lock will lock the door 30 seconds after it has been unlocked. This feature is off by default. You can set the time delay for 30s, 60s, 120s and
• 180s in both Master Mode and the App.

Wrong Entry PIN Code Limit

• After 10 attempts of entering an invalid User PIN Code, the unit will shut down for 3 minutes.

Silent Mode

• The keypad will beep when pushed; but can be muted. Low battery and Wrong Entry User PIN Code Limit alarms will still sound in Silent Mode.
• Low Battery Alarm
  • If the battery indicator keeps flashing, the batteries are getting low. For the best performance replace with four new AA alkaline batteries.
• Unlock With Fake Code
  • Users can prevent PIN Code exposure from strangers by entering random digits before or after the correct PIN Code.

Code Format

1. Master PIN Code (4 to 10 digits): The default Master PIN Code is 12345678. Change the default Master PIN Code before programming other codes.
2. User PIN Code (4 to 10 digits): A total of 20 User PIN Codes (including One-Time PIN Code) can be programmed and stored in the lock.
3.  User Fingerprint: 50 fingerprints can be programmed and stored in the lock.
4. Both Master and User PIN Codes do not support the following combination of numbers.

• Forward number sequence
• Backward number sequence
• Repeat number sequence
• Contain existing code sequence

INSTALLATION INSTRUCTION

Parts List

STEP

Prepare the door and check dimensions

• Measure to confirm that the bore hole is　 1-1/2’’ or 2-1/8″ (38mm or 54mm).
• Measure to confirm that the bore hole is　 1-1/2’’ or 2-1/8″ (38mm or 54mm).
• Measure to confirm that the backset is either 2-3/8″ or 2-3/4″ (60 or 70mm)

• Measure to confirm that the door is 1-3/8″ to 2″ (35mm to  50mm) thick
• Make sure the hole in the door frame is drilled a minimum of 1’’ (25mm) deep, to leave enough space for the deadbolt to extend into the door frame when the door is locked.
• Notes:
  • Make sure the door frame is aligned with the door and there are no obstructions stuck in the door frame

Install the latch and strike

• Determine backset and adjust the latch

• Determine backset and adjust the latch

• Use a screwdriver to test if deadbolt works smoothly

• Install strike on the door frame.

• IMPORTANT:

  • Make sure the hole in door frame is drilled a minimum of 1″ (25mm) deep

• Install exterior assembly

• IMPORTANT:

  • Before installation, make sure the latch is fully retracted (in the unlocked position).

• Measure the diameter of the hole in the door

• With the latch fully retracted (in the unlocked position), route the cable below the latch, and insert the tailpiece through the slot in the latch

• Secure the mounting plate with the supplied screws. Do not overtighten screws

Install interior assembly

• Push the battery  cover up in the direction as illustrated.
• Insert the cable  into the connector. Push the connector in firmly until it is completely attached
• Keep the thumb turn in the vertical position and install the interior assembly.
• Attach interior assembly to mounting plate and tighten 3 screws
• Load 4 AA (1.5V) batteries (Not included) into the battery compartment

Door Handing

• IMPORTANT

  • This step is required and crucial for the lock after installation.

• While keeping your lock unlocked, insert 4 AA alkaline batteries into the battery pack

• Use the Reset Tool to press and  hold the Reset Button for more than 5 seconds until you hear a long “BEEP

• If the reset is successful, the latch bolt will extend on its own to learn the handing orientation of the door

Programming

• IMPORTANT:
  • The default Master Code is 12345678 . It is required that you change it to a code of your own before programming

Factory Default Settings

• How to Reset?
  • Resetting the device will delete all User PIN Codes and Master PIN Code stored in the lock.
• Step 1. Keep the door open and the lock unlocked (thumb turn will be vertical).
• Step 2. Using the Reset Tool, press and hold the Reset Button for 5 seconds until you hear the “BEEP” and the latch extends out automatically.

Troubleshooting

• Make sure the backset on the latch is set to the proper length. Refer to Installation Guide. Make sure prior to installation the latch bolt is retracted. Refer to Installation Guide.
• Please restore to factory default setting and enter the default Master PIN code to set up the lock. Refer to User Guide.

Lock does not smoothly lock or unlock while using the thumb turn.| Confirm the proper mounting screws are installed.
Lock set up failed.|

• Make sure the lock is installed correctly.
• Insert fresh batteries and make sure that the cable is properly connected, not pinched. After installation, reset the lock to the factory default settings.

**** Keypad not responding.|

• Make sure batteries are inserted correctly.
• **** If the battery indicator flashes continuously, the batteries are low. Replace them with four new AA alkaline batteries.
• Make sure that the cable is properly connected and has not been damaged during installation.

Master PIN Code cannot be changed.| Refer to the Quick Start Guide to reset the lock and reprogram all PIN Codes.
I forgot my Master PIN Code.| Perform a factory reset to clear all PIN codes. Once the reset is complete, all PIN Codes will be deleted and the Master PIN Code will be reset to the default Master PIN Code of 12345678.
Auto Lock is not working.| If the battery indicator blinks continuously, the batteries are weak. Replace them with four new batteries to get the best performance (alkaline batteries only). Refer to the Quick Set Up to activate the Auto Lock function.
Fingerprint can’t unlock.| Clean the fingerprint sensor and try again.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:

1. This device may not cause interference.
2.  This device must accept any interference, including interference that may cause undesired operation of the device.
   The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

Warnings

Failure to follow the below instructions could result in damage to the product and void the factory warranty. This manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense.

Product Care

• This lockset is designed to provide the highest standard of product quality and performance. Care should be taken to ensure a long-lasting finish. When cleaning is required, use a soft, damp cloth. Using lacquer thinner, caustic soaps, abrasive cleaners or polishes could damage the coating and result in tarnishing.
• Avoid exposure to direct sunlight. Long-term exposure to direct sunlight may damage the lock.
• Do not install batteries until the lock is completely installed on door.
• User PIN Codes: Can be 4-10 digits and can be set up in the App.
• Sharing Access: Sharing access to your lock means that you are allowing other users to control and track usage of the device. Please be aware of the potential risks it may cause.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>