OttLite CSAQXG00Z-CA LED Lamp with Extendible Wireless Charging Base Instructions
- June 6, 2024
- OttLite
Table of Contents
OttLite CSAQXG00Z-CA LED Lamp with Extendible Wireless Charging Base Instructions
CONGRATULATIONS!
You’ve purchased the finest in natural lighting technology with your new
OttLite® product.
WARNING: To prevent electric shock, make sure the lamp is not plugged in
until all steps are complete.
NOTE: THIS UNIT IS FULLY ASSEMBLED
- Remove lamp from packing, placing lamp body base (A) flat on a steady surface.
- Connect power adapter input (F) into connector (G) in the rear-bottom of the lamp.
- Plug the power adapter (E) into a standard household 120V AC outlet. Note: Only use with the supplied power adapter to avoid damage or fire.
- Turn the lamp ON & OFF using power switch in touch panel (B) located on top of base (A).
- Touch panel (B) includes multiple “touch” keys that control the lamp’s light colour mode and brightness within each colour mode. This lamp provides five levels of brightness. See Touch Key Panel Instructions section for operating instructions.
- Control panel (H) is used to set the lamp’s calendar, alarm setting and display screen light. See Calendar and Clock Setting section for operating instructions.
- To reposition the light, hold base (A) steady and grasp either lamp body (C) or shade (D) depending on needed adjustment
- Refer to Diagrams 1 and 2 for lamp maximum adjustment range. NOTE: DO NOT FORCE the shade or lamp body outside allowable adjustable range as excessive adjustment may cause damage.
TOUCH KEY PANEL INSTRUCTIONS:
To power lamp and operate LED settings, slightly touch required “key” to achieve the following:
- Turn lamp “ON/OFF”: touch key as needed.
- To adjust brightness: touch ∧ or ∨ key as needed.
- To adjust lighting colour mode: touch key to switch light colour mode; 2700K°, 4000K°, 5000K°.
CALENDAR AND CLOCK SETTING:
NOTE: Control Panel (H) to set Calendar and Clock is located on the backside of lamp body (C).
- To set time, push key and the “hour” will flicker, then touch ˆ (up) key and ˇ (down) key to adjust “hour,” after “hour” setting, touch key again to set the “minute,” “year,” “month” and “day.”
- In setting mode, touch M to exit function or operation will stop in one minute.
- When not in setting mode, touch ˆ (up) key to switch between “12h” and “24h” display.
ALARM & SNOOZE FUNCTION SETTING:
- To set the alarm time, press M button located on control panel (H) to activate alarm setting mode. In alarm mode, touch button to set alarm time sequence: “Hour,” “Minute,” “Snooze,” “Music”, then exit. NOTE: There are 8-music tones to select.
- Touch ˆ (up) key and ˇ (down) key to adjust alarm time sequence.
- To activate the alarm press M button to activate the alarm setting mode and then press ˆ (up) key and ˇ (down) key to turn ON/OFF alarm and snooze function. will light up on digital display to indicate alarm is set. will light up to indicate snooze is activated.
- When alarm time is reached, alarm will ring for 1-minute, then snooze and ring again. Touch key to turn off alarm or touch ˆ (up) key or ˇ (down) key to activate snooze.
NOTE: Snooze defaults to 60-minutes, if loss of power occurs.
TEMPERATURE SWITCH SETTING:
- In normal mode, touch ˇ (down) key to switch between ºF and ºC display.
To adjust display screen brightness, touch to choose suitable brightness setting. NOTE: Display screen defaults to “highest” brightness setting when power initially applied.
CONTROL PANEL (H) icon legend
WIRELESS CHARGING INSTRUCTIONS:
Wireless charging requires a Qi-certified device. To determine if your device
is
Qi-certified, please visit the Wireless Power Consortium website.
To wirelessly charge a device, perform the following:
- The wireless charging pad is adjustable for horizontal or vertical charging.
- To charge in horizontal position, simply place the device face up on the middle of the Qi wireless charging icon (J).
- To adjust the charging pad for vertical charging, lift the charging pad up from the lamp base, then adjust the pad up or down to align the Qi wireless charging icon with the center of your device, then place the device face up on the charging pad. See diagram 3.
- When the device is cantered on the Qi wireless charging icon (J), a solid RED light (K) will indicate the device is charging properly. NOTE: If RED light is blinking or is not illuminated, this indicates the device is not charging and needs to be properly cantered.
- Check the charge level on your device periodically to determine when device is fully charged. NOTE: Lamp DOES NOT provide any indication of when device is fully charged.
CAUTION! DEVICE MAY BECOME WARM DURING CHARGING. THIS IS NORMAL AND PART OF THE PROCESS. CHARGING TIMES VARY BY DEVICE
BATTERY REPLACEMENT
- This lamp uses a CR2032 battery. For battery replacement see diagram 4. Battery compartment is located on the backside of lamp body (C).
- To remove/install button cell battery: remove battery compartment door located in the lower half of body section (C) on back-side of lamp. Turn door counter clock-wise to remove and clock-wise to install. Button cell battery is to be installed with the “+” or flat side facing upward.
SAFETY WARNING:
- CAUTION: DO NOT INGEST BATTERY; CHEMICAL BURN HAZARD!
- This lamp contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just two hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
NOTE: Coin/button cell batteries are small, single cell devices having a diameter greater than their height.
SAFETY WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK,
OR INJURY TO PERSONS
- Turn lamp off and WAIT UNTIL LAMP HEAD (D) AND ADAPTER (E) ARE COOL before handling.
- The LED panel located in shade (D) might get hot after several hours of continuous use DO NOT place your hands directly on LED light panel.
- Never use with an extension cord unless the plug can be fully inserted into the receptacles in the extension cord.
- Do not alter the plug. 5. The lamp head included with this unit cannot be replaced by the consumer.
NOTE: The important safety instructions appearing in this instruction sheet are not meant to cover all possible conditions and situations that may occur. It must be understood that common sense, caution, and care must be used with any electrical product.
CAUTION! IF THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD. INDOOR USE ONLY.
CAUTION! THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE
LIGHT
SOURCE REACHES ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
FCC PART 15
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that of the receiver.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment. This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation
FCC/IC RF RADIATION EXPOSURE STATEMENT CAUTION: To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20cm from nearby persons.
IC CANADA
This device contains licence-exempt transmitter(s)/receiver that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: 1. This device may not
cause interference. 2. This device must accept any interference, including
interference that may cause
undesired operation of the device.
IC RF RADIATION EXPOSURE STATEMENT CAUTION: To maintain compliance with the RF exposure guidelines, place the product at least 10cm from nearby persons.
CAN RSS-216/CNR-216
CAN ICES-005 (B)/NMB-005 (B)
CAUTION: Any change or modification to product not expressly recognized by OttLite Technologies voids OttLite’s responsibility for proper function of product.
POWER ADAPTER SPECIFICATION:
Input: AC 100-240V, 50/60 Hz, 0.9A
Output: 12V DC, 2.5A with a Male DC Plug
Qi CHARGER SPECIFICATION:
Output: up to 5 Watts depending on device
The “Qi” symbol is a trademark of the Wireless Power Consortium
THIS LAMP CONTAINS a 5V, 2,1A USB output port (L) located on the bottom rear of lamp. USB port can charge items such as tablets, cellular phones, etc.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>