regalo 1165 W Easy Step Extra Wide Safety Gate Instruction Manual
- October 27, 2023
- regalo
Table of Contents
regalo 1165 W Easy Step Extra Wide Safety Gate
- READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE.
KEEP INSTRUCTIONS FOR FUTURE USE.
Before Assembly
PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS:
- A 4″ Extension (1)
- B Gate Frame (1)
- C 4″ Extension (1)
- D Wall Cups (4)
- E 1” Wall Mount Screws (4)
- F Threaded Spindle Rods (4)
BEFORE USING PRODUCT
Read and follow all instructions carefully to ensure that your gate and
extensions are properly installed. Improper installation could result in the
gate becoming unstable or dislodged from the doorway. Always make sure the
extension is securely attached to the gate before using. The safety of your
child is your responsibility. Please keep these instructions for your
reference.
IMPORTANT
- Never use more than two extensions per side of gate.
- If hardware mounting to a surface other than drywall or wood, please consult with a professional about installation.
- Base locks are to be used at all times, on both sides of the gate.
- MODEL NO. MAX SIZE
REMOVING YOUR GATE FROM THE WALL
To remove your gate from the wall, rotate the adjustment wheels on each of the
(4) threaded spindle rods to depressurize the gate from its doorway or
opening. Then, gently pull or push the gate free from its doorway or opening.
CARE AND MAINTENANCE
Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged. Check the gate regularly to ensure all the hardware and mountings are tightened. Do not use abrasive cleaners or bleach. Clean by sponging with warm water and a mild detergent.
Assembling and Installing Your Gate
Locate the (4) threaded spindle rods (F) Rotate the adjustment wheels along
the threading, eliminating the gap between the adjustment wheel and the rubber
foot.
NOTE:
You will notice a slight gap between the gate door latch and the frame. This
is not a defect. Your gate is a pressure mounted gate and this gap will
disappear once you tighten your gate in its opening. Insert the (4) threaded
spindle rods into the holes at each of the four corners of the gate.
NOTE:
It may be necessary to hold the threaded spindle rods or rubber feet while
rotating the adjustment wheels to ensure the entire unit does not rotate.
Position the gate (B) so that it is level and centered within your doorway or
opening. Rotate the adjustment wheels on the threaded spindle rods in the
opposite direction as in Step 1, expanding the gap between the rubber foot and
the adjustment wheel. Expand each of the (4) threaded spindle rods until they
make contact with the doorway or opening. Do not fully tighten the threaded
spindle rods yet.
NOTE:
The gap between the gate and wall should not exceed more than 2.5 inches.
Make the appropriate adjustment to ensure you have installed your gate safely.
When you are satisfied with the general placement of your gate,
fully tighten the threaded spindle rods attached to the lower corners of the
gate by further rotating the adjustment wheels. Continue by tightening the
upper threaded spindle rods. As you tighten the threaded spindle rods, you
will notice the gap between the door frame and the secure lift latch begin to
narrow. In order for the gate to function properly, stop tightening the upper
threaded spindle rods just before the outer housing of the secure lift latch
and the receiving component touch.
NOTE:
There should be equal spacing among each of the (4) threaded spindle rods.
Make the appropriate adjustment to ensure you have installed your gate safely.
Operating the Door Latch
Pull the spring lock away from the secure lift latch while simultaneously
lifting the lock lever upwards. This will release the locking latch from the
gate frame and allow the door to push or pull open. To lock the door shut,
close the door completely, then push down on the lock lever to re-engage the
spring lock.
NOTE:
If your secure lift latch is not properly engaging with the receiving
component, ensure that your gate is level, mounted properly, and that you have
not over-tightened the threaded spindle rods.
At the bottom of the gate door, rotate the base lock to the horizontal
position to allow the door to swing open.
NOTE:
Place lock down on side occupied by the child.
Positioning and Attaching Wall Cups
After you have mounted your gate, and you are satisfied with its positioning,
draw a circle on the surface of your doorway or opening around the perimeter
of the (4) rubber feet. Next, completely remove the gate from the opening by
loosening each of the (4) threaded spindle rods to depressurize the gate. With
the gate fully removed, you can now use the circles you marked during Step 1
as guides for screwing in your (4) wall cups (D). Center each of the wall cups
within the guide circles and use the provided self-tapping 25mm screws (E) to
fasten them in place via the hole through the center of each wall cup.
Reinstall your gate in the doorway or opening according to the instructions,
using the newly installed wall cups as anchoring points for the (4) threaded
spindle rods.
WARNING
NOTE:
The gap between the gate and wall should not exceed more than 2.5 inches.
- INST ALL ACCORDING TO MANUFACTURER’S INSTRUCTIONS.
- TO PREVENT SERIOUS INJURY OR DEATH, SECURELY INSTALL GATE OR ENCLOSURE AND USE ACCORDING TO MANUFACTURER’S INSTRUCTIONS.
- CHILDREN HAVE DIED OR BEEN SERIOUSLY INJURED WHEN GATES ARE NOT SECURELY INSTALLED. ALWAYS INSTALL AND USE AS DIRECTED USING ALL REQUIRED PARTS.
- YOU MUST INSTALL WALL CUPS TO KEEP GATE IN PLACE. WITHOUT WALL CUPS, CHILD CAN PUSH OUT AND ESCAPE.
- NEVER STACK GATES ON TOP OF EACH OTHER TO FORM A TALLER BARRIER. THIS COULD RESULT IN SERIOUS INJURY OR DEATH.
- STOP USING WHEN A CHILD CAN CLIMB OVER OR DISLODGE THE GATE.
- USE ONLY WITH THE LOCKING MECHANISM SECURELY ENGAGED.
- TO PREVENT FALLS, NEVER USE AT TOP OF STAIRS.
- NEVER USE TO KEEP CHILD AWAY FROM POOL.
- INTENDED FOR USE WITH CHILDREN FROM 6 MONTHS THROUGH 24 MONTHS.
- ALWAYS ENSURE THE GATE IS RESTING AGAINST THE FLOOR BEFORE BEGINNING INSTALLATION.
- THIS PRODUCT WILL NOT NECESSARILY PREVENT ALL ACCIDENTS. NEVER LEAVE CHILD UNATTENDED.
- CHECK THE GATE REGULARLY TO SEE IF ALL THE HARDWARE AND MOUNTINGS ARE TIGHTENED.
- DO NOT USE IF ANY COMPONENT IS MISSING OR DAMAGED.
- ADULT ASSEMBLY REQUIRED.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>